Search Results

Multicore processor are well established in classical and tablet personal computers for some year. Such processors use more then one central core for computation and allow to integrate more computational power with smaller costs. However more than 90% of all processors worldwide are not placed in classical IT but are empedded in bigger systems like in modern vehicles or airplanes. Such systems face a very high demand in terms of safety, security an reliability which hinders the use of multicores in such systems. The funded project ARAMiS faces these demands and has the goal to enable the usability of multicore systems in the domains automotive and avionics, as well as later also railway. ARAMiS is the basis for higher traffic safety, traffic efficiency and comfort.

In ride comfort as well as driving dynamics, the behavior of the vehicle is affected by several subsystems and their properties. When analyzing the suspension, especially the characteristics of the main spring and damper but also rubber bushings are of main importance. Still, the properties of the different components are dependent on the present operating conditions. Concerning rubber bushings, several effects have already been investigated, e.g. dependencies of the transfer function of frequency, amplitude or load history. In this context influences of changes in temperature are often neglected. However, in the following research, the focus specifically lies on determination and analysis of the temperature dependency of rubber bushings. For this purpose, initially the relationship between properties of pure rubber and rubber bushings is described, which serves as a basis for correlating respective temperature dependencies.

The open jet wind tunnel is a widespread test section configuration for developing full scale passenger cars in the automotive industry. However, using a realizable nozzle cross section for cost effective aerodynamic development is always connected to the presence of wind tunnel effects. Wind tunnel wall interferences which are not present under open road conditions, can affect the measurement of aerodynamic forces. Thus, wind tunnel corrections may be required. This work contains the results of a CFD (Computational Fluid Dynamics) approach using unsteady Delayed Detached Eddy Simulations (DDES) to evaluate wind tunnel interferences for open jet test sections. The Full Scale DrivAer reference geometry of the Technical University of Munich (TUM) using different rear end shapes has been selected for these investigations.

With the introduction of the ISO26262 automotive safety standard there is a burden of proof to show that the processing elements in embedded microcontroller hardware are capable of supporting a certain diagnostic coverage level, depending on the required Automotive Safety Integrity Level (ASIL). The current mechanisms used to provide actual metrics of the Built-in Self Tests (BIST) and Lock Step comparators use Register Transfer Level (RTL) simulations of the internal processing elements which force faults into individual nodes of the design and collect diagnostic coverage results. Although this mechanism is robust, it can only be performed by semiconductor suppliers and is costly. This paper describes a new solution whereby the microcontroller is synthesized into a large Field Programmable Gate Array (FPGA) with a test controller on the outside.

Aeroacoustics of road vehicles is becoming more and more important as it directly affects the comfort of the passengers. The tests made in the wind tunnel, in low-turbulence flow conditions, show results that are qualitatively different from those measured on the road. To get a better understanding of this, Audi and Pininfarina decided to carry out a test campaign on some cars, both on the road and in the wind tunnel, in various turbulent flow conditions. In the case of road measurements, some typical turbulent flow conditions, like those caused by atmospheric wind and those produced by the traffic, have been investigated. Wind tunnel measurements have been performed both in the base wind tunnel (in Audi and in Pininfarina) and in the presence of turbulent flows generated, in the Pininfarina wind tunnel, by the Turbulence Generator System, already described in previous SAE papers [1,3,5,7].

In open jet wind tunnels with high blockage ratios a sharp rise in drag is observed for models approaching the nozzle exit plane. The physical background for this rise in drag will be analyzed in the paper. Starting with a basic analysis of the dependencies of the effect on model and wind tunnel properties, the key parameters of the problem will be identified. It will be shown using a momentum balance and potential flow theory that interaction between model and nozzle exit can result in significant tunnel-induced gradients at the model position. In a second step, a CFD-based investigation is used to show the interaction between nozzle exit and a bluff body. The results cover the whole range between open jet and closed wall test section interaction. The model starts at a large distance from the nozzle, then moves towards the nozzle, enters the nozzle and is finally completely inside the nozzle.

The ever increasing use of electronics in modern vehicles has not stopped at comfort systems such as power seats and power windows. Every conventional system that requires operating force will eventually be replaced by a self-powered version. One such item is the electromechanical parking brake of the new Audi A8, offering a host of new features. Despite the many options for new functions, it is nevertheless important to keep the driver in mind. Being engineers, one tends to overlook that not all customers share our excitement for gadgets and overly complicated technical features.

In order to suppress the well-documented low frequency pressure fluctuations in open jet wind tunnels, termed ‘wind tunnel buffeting’, an Active Resonance Control (ARC) System was implemented in the Audi aero-acoustic wind tunnel several years ago. This ARC-Sys-tem reduces the periodic pressure fluctuations by up to 23 dB and completely eliminates the periodic velocity fluctuations using a simple feedback control scheme. To set up the ARC system in practice, the system's parameters are optimised once for each critical flow velocity, when the vortex shedding frequency coincides with an acoustic resonance mode of the wind tunnel. Due to the fact that both frequency and amplitude of the excited resonances not only depend on flow velocity but also on other parameters such as collector position and test-car geometry, the system has to be adjusted with regard to each of these cases.

The classical theory of wind tunnel corrections calculated from potential flow theory is revisited. In this context a flow model uniformly valid for all types of test sections is developed for the correction of drag in automotive wind tunnels. To define and size the singularities setting up the flow model only geometrical properties of the model and measured force coefficients will be used. To achieve a correct representation of the flow about a vehicle body a number of improvements to the classical approach are proposed. Based on the uniformly valid flow model, correction formulae for closed wall, open jet and slotted wall test sections are given. For the open jet and slotted wall case it is shown, that the presented formulae are still incomplete, whereas for the closed wall case the correction is ready to use. The correction approach is validated step by step by comparison with appropriate experimental data.

Optimization of ride comfort is becoming increasingly important in chassis development. Constantly rising traffic density and comfort-orientated customer preferences are mainly responsible for this. Comfort and its improvement are important, not only on bad road surfaces, but also on even surfaces. The complexity of analysis leads to a strong link between car testing and simulation. The testing itself is divided in to roadtests and test stands. It is of outstanding importance to analyze the vehicles vibrational behavior from road tests as it is a real life situation. In order to get meaningful results from the roadtest the vehicle has to be seen as a complete vibrational system. The vibrational behavior of a system is clearly defined by input and output of the system. Road tests are chosen in relation to the predicted car. The roads surface is the input of the system exciting the vibrational subsystems of a car. The ride tests are used for the evaluation of drive response behavior.

A region with floor boundary-layer suction upstream of the vehicle to remove the oncoming boundary layer is often used in automotive wind tunnels. These suction systems inevitably change the empty-tunnel pressure gradient. In this paper, the empty-tunnel pressure gradient created by the use of boundary layer suction and its effect on measured drag are investigated. By using excess suction - more suction than necessary to remove the floor boundary layer – it was possible to show experimentally that the major part of the drag increase due to boundary layer suction is created by unintended gradient effects. Only a minor part of the drag increase is due to the increased flow velocities at the lower parts of the vehicle, or in other words, due to the improved ground simulation. A theoretical model, using the concept of horizontal buoyancy to predict the gradient effect, is proposed. The model is compared to the experimental results as well as to CFD calculations.

The reference pressures are determined in automotive wind tunnels by measurement of pressures and pressure differences at upstream positions along the wind tunnel nozzle. For closed wall wind tunnels usually the so called nozzle method is used, where the volume flux is calculated from a pressure difference measured at the nozzle contour and a calibration factor determined in the empty test section. For open jet wind tunnels a choice is available between nozzle and plenum method. For the plenum method the reference static pressure is taken from the plenum chamber and the dynamic pressure also refers to the plenum conditions. The static reference pressure in closed wall tunnels is calculated by subtracting the dynamic pressure from the total pressure in the settling chamber. In this paper, the definitions and the differences between the two methods are discussed in detail.

With increasing levels of driving automation, the perception provided by automotive environment sensors becomes highly safety relevant. A correct assessment of the sensors’ perception reliability is therefore crucial for ensuring the safety of the automated driving functionalities. There are currently no standardized procedures or guidelines for demonstrating the perception reliability of the sensors. Engineers therefore face the challenge of setting up test procedures and plan test drive efforts. Null Hypothesis Significance Testing has been employed previously to answer this question. In this contribution, we present an alternative method based on Bayesian parameter inference, which is easy to implement and whose interpretation is more intuitive for engineers without a profound statistical education. We show how to account for different environmental conditions with an influence on sensor performance and for statistical dependence among perception errors.

The potential of determining the change of injury severity in the accident event taking passive as well as active measures into account at the vehicle (integral systems) are at present limited to pedestrian protective systems. Therefore, an extension of the existing methods for the application with common integral systems (front protection, side protection, etc.) is suggested. Nowadays the effectiveness of passive safety systems is determined in crash tests with very high accident severities. However, approximately 90% of real-world accidents have a lower accident severity as the required crash tests. Thus, this paper will present a method calculating the effectiveness of such an integral system based on real-world accident data. For these reasons, this paper is presenting a method for a more valid prediction of injury severity. The German In-Depth Database GIDAS allows clustering the accident event in relevant car-to-car scenarios.

ISO 26262 is the actual standard for Functional Safety of automotive E/E (Electric/Electronic) systems. One of the challenges in the application of the standard is the distribution of safety related activities among the participants in the supply chain. In this paper, the concept of a Safety Element out of Context (SEooC) development will be analyzed showing its current problematic aspects and difficulties in implementing such an approach in a concrete typical automotive development flow with different participants (e.g. from OEM, tier 1 to semiconductor supplier) in the supply chain. The discussed aspects focus on the functional safety requirements of generic hardware and software development across the supply chain where the final integration of the developed element is not known at design time and therefore an assumption based mechanism shall be used.

The present paper reveals the design concept as well as results of experimental investigations, which were conducted in the early design stage of the planned AUDI Aero-Acoustic Wind Tunnel. This low-noise open-jet facility, featuring a nozzle exit area of 11 m2 and a top speed of approximately 60 m/s, enables aerodynamic as well as acoustic testing of both, full-scale and model-scale ground vehicles. Ground simulation is provided by means of a moving-belt rig. The surrounding plenum is designed as a semi-anechoic chamber to simulate acoustic free-field conditions around the vehicle. Fan noise will be attenuated below the noise level of the open jet. The work reported herein, comprises 1/8-scale pilot-tunnel experiments of aerodynamic and acoustic configurations which were carried out at the University of Darmstadt.

This paper deals with the correction of aerodynamic interference effects taking place between the nozzle of an open jet wind tunnel and a test model. In order to deduce correct aerodynamic coefficients these interference effects have to be allowed for in the determination of the correct wind tunnel speed. In open jet wind tunnels basically two different methods are used to determine the tunnel speed. One is the so-called nozzle-method, utilizing the pressure difference down the nozzle to determine the nozzle exit velocity or tunnel speed. The other procedure is the so-called plenum-method, where the pressure difference between the settling chamber and the surrounding plenum chamber of the test section is measured and used. In this paper it is shown that both methods yield a systematic error, since the velocity distribution in the nozzle differs from the velocity distribution in an unbounded stream measured at the same distance from the model.

The increased pressure for power, space, and cost reduction in automotive applications together with the availability of high performance, automotive qualified multicore microcontrollers has lead to the ability to engineer Domain Controller ECUs that can host several separate applications in parallel. The standard automotive constraints however still apply, such as use of AUTOSAR operating system, support for legacy code, hosting OEM supplied code and the ability to determine warranty issues and responsibilities between a group of Tier 1 and Tier 2 vendors who all provide Intellectual Property to the final production ECU. Requirements for safety relevant applications add even more complexity, which in most current approaches demand a reconfiguration of all basic software layers and a major effort to redesign parts of the application code to enable co-existence on the same hardware platform. This paper outlines the conflicting requirements of hosting multiple applications.

For the aerodynamic development of an aircraft the induced drag is an important quantity and it has a significant impact on the design of the wing. The induced drag corresponds to the power requirement of the wing to generate the necessary lift. In many cases this is the dominant source of drag for aircraft. In ground vehicle aerodynamics the concept of induced drag up to now has attracted much less attention. This is partly due to the fact, that vehicle aerodynamicists usually optimize the vehicles to generate little or no lift. The second reason is that it is much more difficult for a ground vehicle to separate the total drag into the different contributions. During wind tunnel tests of vehicles with and without ground simulation some astonishing results were found, especially when comparing results for different rear end shapes.

Audi's new full scale aeroacoustic wind tunnel is under full operation now. The new facility is designed for full scale automotive testing of aerodynamics and aeroacoustics for vehicles up to 3 m2 frontal area at wind speeds up to 300 kph. The highlights are the unique ground simulation system with boundary layer suction and a 5-belt-system, and the extremely low background noise of only 60 dB(A) at 160 kph. First the background of the project is illustrated and the need for the special features of the tunnel is deduced form the industrial requirements. Then an overview of the facility design is given with a detailed description of the key technical components. The calibration of the self-correcting test section will be discussed and the physical background for it will be examined more closely. For the calibrated wind tunnel the results of two correlation tests including open jet as well as closed wall wind tunnels show a reasonable conformity.