Search Results

Transient and steady-state kinetic data are herein presented to analyze the inhibiting effect of ammonia on the NH₃-SCR of NO at low temperatures over a Fe-zeolite commercial catalyst for vehicles. It is shown that in SCR converter models a rate expression accounting for NH₃ inhibition of the Standard SCR reaction is needed in order to predict the specific dynamics observed both in lab-scale and in engine test bench runs upon switching on and off the ammonia feed. Two redox, dual site kinetic models are developed which ascribe such inhibition to the spill-over of ammonia from its adsorption sites, associated with the zeolite, to the redox sites, associated with the Fe promoter. Better agreement both with lab-scale intrinsic kinetic runs and with engine test-bench data, particularly during transients associated with dosing of ammonia to the SCR catalyst, is obtained assuming slow migration of NH₃ between the two sites.

Typical design challenges for Unmanned Aerial Vehicles (UAVs) require low aerodynamic drag and structural weight. Both of these requirements imply that these aircraft are considerably more flexible than conventional aircraft and their stability analyses are more complex since they require models unifying rigid body and elastic dynamics. This paper aims to built such a model for a generic UAV. The model is then used to address stability in terms of divergence and flutter.

It is estimated that operating continuously on a B20 fuel containing the current allowable ASTM specification limits for metal impurities in biodiesel could result in a doubling of ash exposure relative to lube-oil-derived ash. The purpose of this study was to determine if a fuel containing metals at the ASTM limits could cause adverse impacts on the performance and durability of diesel emission control systems. An accelerated durability test method was developed to determine the potential impact of these biodiesel impurities. The test program included engine testing with multiple DPF substrate types as well as DOC and SCR catalysts. The results showed no significant degradation in the thermo-mechanical properties of cordierite, aluminum titanate, or silicon carbide DPFs after exposure to 150,000 mile equivalent biodiesel ash and thermal aging. However, exposure of a cordierite DPF to 435,000 mile equivalent aging resulted in a 69% decrease in the thermal shock resistance parameter.

It is well known that the drilling industry is a diverse industry with huge power needs for drilling deep wells. This paper discusses the drilling industry in general and the future need for HT power electronics to enable such activities as tractor drive drilling of deep horizontal wells. The discussion is geared at applications for drilling within the earth at ambient temperatures of 150°C and above.

In the paper some methods are presented, with the corresponding practical examples, related to MonteCarlo (MC) techniques for thermal model/test correlation purposes. The MonteCarlo techniques applied to model correlation are intended to be used as an alternative to empirical ‘manual’ correlation techniques, gradients methods, matrix methods based on least square fit minimization. First of all, Design Of Experiments (DoE) tools are used to determine the model response to uncertain parameters and the confidence level of such a response. A sensitivity map is built, allowing the design of the test to maximize the response of the system to the uncertain parameters. Techniques derived from the extreme statistics are used to extrapolate data beyond test limits, with a sufficient confidence in the queue behaviour.

Future human exploration roadmaps involve the development of temporary or permanent outposts on Moon and Mars. The capability of providing astronauts with proper conditions for living and working in extraterrestrial environments is therefore a key issue for the sustainability of those roadmaps, and closed-loop Environment Control and Life Support Systems (ECLSSs) and bio-regenerative plants represent the necessary evolution of current technologies for complying with the challenging requirements imposed. This paper presents the architectural design of a terrestrial plant to be exploited to test and validate air and water management technologies for a biological life support system in a closed environment. The plant includes a crew area and a plant growth area. These two spaces can be considered as either a unique volume or two separated environments with reduced contact, e.g. for plant harvesting or other up-keeping activities.

The sustainability of Martian outposts development is strongly based on the capability of achieving a high level of autonomy both in terms of operations management and of resources availability. In situ production of consumables is a key point to allow humans to work and live on Mars avoiding or limiting the need for re-supplies of materials from Earth. Required consumables can be produced in situ exploiting the locally available resources, but also by means of green-houses and waste recycle systems. Dedicated robotic missions for in situ demonstration of this type of technologies are a fundamental step of the Martian In Situ Resources Utilization (ISRU) development roadmap. This paper is focused on the extraction of oxygen and fuels (e.g. methane) from the Martian atmosphere, and presents a feasibility study for a small technological demonstration plant.

The continued availability of leaded specialty aviation gasolines remains as an item of crucial importance in the near-term future of general aviation; however, the development of new piston engines capable of operation with other transportation fuels available in large pools is considered an indispensable element in the long-range survival of the industry. This paper offers a road map that while allowing the continued utilization of the current fleet of piston aircraft, sets the stage for a transition to new piston powerplants and associated aircraft, compatible with widely available transportation fuels such as motor gasoline based aviation fuels for the lower and some medium performance aircraft, and aviation turbine fuels for the balance of medium and high performance airplanes.

An experimental campaign is presented aiming at the characterization of thermal dissipation of batteries to be used on board of small satellites. A suitably designed device allows to manage automatically the orbital cycling simulation between battery cell charge and discharge. The cell thermal performance is characterized in various combinations of temperature, discharge current and Depth of Discharge. The gathered data are used for providing guidelines in the design of a family of Italian Small Satellites.

An outer loop guidance architecture was designed to control autonomous aerial refueling mission from the trail aircraft side. The design utilized bank, yaw rate, velocity and climb rate commands implemented using a previously developed adaptive trajectory concept. The concept was based on position error feedback that was used to control trail aircraft overshoot and tracking about the lead aircraft refueling point. To demonstrate this application, an open loop linear trail aircraft model at a given flight condition was selected. Inner loop control laws were designed using Linear Quadratic Regulator feedback controller and Balanced Deviation theory. The outer loop guidance architecture was then added to implement the application. The performance of the system was then evaluated for a selected position error, and disturbance.

In the paper several application techniques of MonteCarlo (MC) method applied to thermal analysis of space vehicles are presented. Although these methods are widely used in other engineering domains, their introduction to the thermal one is quite recent and not fully developed in the industrial practice. This paper aims at showing that, even without demanding computation resources (all what presented has been obtained with a single processor PC) MonteCarlo analysis techniques, in a preliminary design phase, can support and integrate engineering judgment of the thermal designer. In particular, it is exploited the applicability of the method to reduced thermal models, with a clear advantage in terms of computation time. An original approach is proposed, and results are shown. The papers shows the applicability of the MC method to the case when experimental data of the uncertain parameters are available, using the bootstrap re-sampling techniques.

The ideal internal-combustion crankshaft engine would burn all the fuel near top center without detonation, then expand the whole charge until exhaust Both events are impossible with current piston engines. The Hydrocycle Rocket Piston Engine concept employs a free piston in the head of a two-stroke-cycle engine. Combustion between the crank piston and the free piston allows direct conversion of combustion fluid expansion to hydrostatic fluid flow and accumulator gas compression with perfect timing and minimum thermal and mechanical losses. An infinitely variable, radial hydrostatic motor gives the driver smooth, gas-cushioned acceleration and stepless performance. Maximum economy is attained since the driver is forced to run the engine at optimum minimum speed to match road load oadin all traffic conditions.

In the future, it will be possible to manufacture very small, robust machines, which may be attached to the surface of a wing allowing the classic boundary condition of “no-slip” to be altered at will. It is also possible that the heat transfer through the wing surface can be controlled. This paper reports an investigation into the possible benefits to aerodynamics that will occur if such machines become available. It is found that imposing an isothermal wing surface can increase the lift drag ratio of wing at transonic cruise and allowing slip at the surface can have the same effect. Both these effects are additive. It is found that control of heat transfer on a wing at hypersonic wing can act as a control device, comparable to that due a moderate flap deflection.

This paper deals with a conceptual aircraft cargo loader “that can do everything” commonly referred to as The Super Loader. The Super Loader is intended for use at air terminals to transport loads such as palletized cargo, containers, wheeled vehicles, shelters, and airdrop platforms from the storage docks to the military and civil aircraft, and vice versa. The loader may be described as a self-propelled, air transportable (in a C-141, C-17, C-5) 60,000 lb lifting capacity, adjustable height vehicle that will load/off load all transport aircraft from a C-130 whose cargo deck is only 3 feet, 3 inches high to a B-747 whose main deck upper limit is about 18 feet high. The Super Loader must also service the lower lobes of wide-bodies and main decks of narrow-bodied aircraft like the DC-8 and B-707. In brief, this loader will be required to interface with both civil and military cargo systems, present and future.

Of the many research approaches investigated over the years to measure the lubrication properties of aviation turbine fuels, the Ball-on-Cylinder Lubricity Evaluator (BOCLE) has emerged as the most significant test. BOCLE was originally a lubricant research device modified for low viscosity jet fuel when the Air Force encountered fuel control problems in 1965 with JP-4. It proved to be capable of detecting the presence of additives such as corrosion inhibitors which improve boundary lubrication properties and also the absence of natural lubricity agents in highly refined jet fuel. The Coordinating Research Council carried out several programs to investigate test variables such as cylinder type, humidity control and load. A semi-automated version using Falex test rings has now been commercialized and is being used to test fuels from aircraft experiencing abnormal pump wear and fuel control hang-up.

The aerodynamics of the STOL aircraft can experience significant changes in proximity to the ground. A review of the existing data base and methodologies has been made and the results of that review are presented in this paper. The existing data show that in ground proximity the STOL aircraft will generally experience a reduction in the lift component regardless of the lifting configuration. Those configurations with integrated power and lift systems will have an additional effect of ground induced aerodynamic changes. This paper will discuss the existing data base and the deficiencies of that data base.

Wind turbines in cold climates are likely to suffer from icing events, deteriorating the aerodynamic performances of the blades and decreasing their power output. Continuous ice accretion causes an increase in the ice mass and, consequently, in the centrifugal force to which the ice shape is subjected. This can result in the shedding of chunks of ice, which can jeopardize the aeroelastic properties of the blade and, most importantly, the safety of the surrounding people and of the wind turbine structure itself. In this work, ice shedding analysis is performed on a quasi-3D, multi-step ice geometry accreted on the NREL 5MW reference wind turbine. A preliminary investigation is performed by including the presence of an ice protection system to decrease the adhesion surface of the ice on the blade. A reference test case with a simple geometry is used as verification for the correct implementation of the procedure.

This work presents a comprehensive numerical model for ice accretion and Ice Protection System (IPS) simulation over a 2D component, such as an airfoil. The model is based on the Myers model for ice accretion and extended to include the possibility of a heated substratum. Six different icing conditions that can occur during in-flight ice accretion with an Electro-Thermal Ice Protection System (ETIPS) activated are identified. Each condition presents one or more layers with a different water phase. Depending on the heat fluxes, there could be only liquid water, ice, or a combination of both on the substratum. The possible layers are the ice layer on the substratum, the running liquid film over ice or substratum, and the static liquid film between ice and substratum caused by ice melting. The last layer, which is always present, is the substratum. The physical model that describes the evolution of these layers is based on the Stefan problem. For each layer, one heat equation is solved.

This paper presents a novel fully-automatic remeshing procedure, based on the level-set method and Delaunay triangulation, to model three-dimensional boundary problems and generate a new conformal body-fitted mesh. The proposed methodology is applied to long-term in-flight ice accretion, which is characterized by the formation of extremely irregular ice shapes. Since ice accretion is coupled with the aerodynamic flow field, a multi-step procedure is implemented. The total icing exposure time is subdivided into smaller time steps, and at each time step a three-dimensional body-fitted mesh, suitable for the computation of the aerodynamic flow field around the updated geometry, is generated automatically. The methodology proposed can effectively deal with front intersections, as shown with a manufactured example.

This study examines the impact of slip in aero-thermal conditions of supercooled large droplets (SLD) produced in an Icing Wind Tunnel (IWT) on the ice accretion characteristics. The study identifies potential biases in the SLD model development based on IWT data and numerical predictions that assume the SLD to be in aerothermal equilibrium with the IWT airflow. To obtain realistic temperature and velocity data for each droplet size class in the test section of the Braunschweig Icing Wind Tunnel (BIWT), a Lagrangian droplet tracking solver was used within a Monte Carlo framework. Results showed that SLDs experience considerable slips in velocity and temperature due to their higher inertia and short residence time in the Braunschweig IWT. Large droplets were found to be warmer and slower than the flow in the test section, with larger droplets experiencing larger aerothermal slips.