Search Results

Over 30 years ago, A. H. Vincent of Westland Helicopters demonstrated that if a structure is excited harmonically, the response at another position (at a fixed frequency) will trace a circle in the complex plane as a result of a dynamic stiffness modification between two points. As either the real or imaginary part of an introduced dynamic stiffness is varied from minus infinity to plus infinity, the structural or acoustic response on any position will map a circle in the complex plane. This paper reviews the basis for this little known principle for vibro-acoustics problems and illustrates the viability for a cantilevered plate example. The applicability of the method is then considered for strictly acoustic systems like intake and exhaust systems. Specifically, it is shown that the response traces a circle in the complex plane if either the real or imaginary parts of the source or termination impedance are varied from minus to plus infinity.

Noise concerns regarding snowmobiles have increased in the recent past. Current standards, such as SAE J192 are used as guidelines for government agencies and manufacturers to regulate noise emissions for all manufactured snowmobiles. Unfortunately, the test standards available today produce results with variability that is much higher than desired. The most significant contributor to the variation in noise measurements is the test surface. The test surfaces can either be snow or grass and affects the measurement in two very distinct ways: sound propagation from the source to the receiver and the operational behavior of the snowmobile. Data is presented for a known sound pressure speaker source and different snowmobiles on various test days and test surfaces. Relationships are shown between the behavior of the sound propagation and track interaction to the ground with the pass-by noise measurements.

Micro-perforated (MPP) panels are acoustic absorbers that are non-combustible, acoustically tunable, lightweight, and environmentally friendly. In most cases, they are spaced from a wall, and that spacing determines the frequency range where the absorber performs well. The absorption is maximized when the particle velocity in the perforations is high. Accordingly, the absorber performs best when positioned approximately a quarter acoustic wavelength from the wall, and larger cavity depths improve the low frequency absorption. At multiples of one half acoustic wavelength, the absorption is minimal. Additionally, the absorption is minimal at low frequencies due to the limited cavity depth behind the MPP. By partitioning the backing cavity, the cavity depth can be strategically increased and varied. This will improve the absorption at low frequencies and can provide absorption over a wide frequency range.

Partial enclosures are commonly utilized to reduce the radiated noise from equipment. Often, enclosure openings are fitted with silencers or louvers to further reduce the noise emitted. In the past, the boundary element method (BEM) has been applied to predict the insertion loss of the airborne path with good agreement with measurement. However, an alteration at the opening requires a new model and additional computational time. In this paper, a transfer function method is proposed to reduce the time required to assess the effect of modifications to an enclosure. The proposed method requires that the impedance at openings be known. Additionally, transfer functions relating the sound pressure at one opening to the volume velocity at other openings must be measured or determined using simulation. It is assumed that openings are much smaller than an acoustic wavelength. The sound power from each opening is determined from the specific acoustic impedance and sound pressure at the opening.

Helmholtz resonators are often used in the design of vehicle mufflers to target tonal noise at a few specific low frequencies generated by the engine. Due to the uncertainty of temperature variations and different engine speeds, multiple resonators may have to be built in series to cover a narrow band of frequencies. Double-tuned Helmholtz resonators (DTHR) normally consist of two chambers connected in series. Openings or necks are created by punching small slots into a thin-walled tube which provide a natural neck passage to the enclosing volume of the Helmholtz resonator. In this paper, numerical analyses using both the boundary element (BEM) and the finite element (FEM) methods are performed and simulation results are compared against one another. A typical real-world muffler configuration commonly used in passenger vehicles is used in a case study.

Intake, exhaust, and heating / air conditioning systems in automobiles consist of various common duct elements. Noise arises primarily due to the source and is attenuated using common elements like expansion chambers and resonators. This attenuation is straightforward to predict using plane wave simulation and more advanced numerical methods. However, flow noise is often an unexpected important noise source. Predictions require computer intensive analyses. To better understand the aeroacoustic sources in duct systems, a flow rig has been developed at the University of Kentucky. The flow rig consists of a blower, a silencer to attenuate blower noise, external noise sources, and then the test duct. The flow rig can be equipped with an anechoic termination to measure transmission loss or may be used to measure insertion loss directly. In the latter case, the sound power is measured from the pipe outlet inside of a hemi-anechoic chamber.

The insertion loss of louvered terminations positioned at the end of a rectangular duct is determined using acoustic finite element analysis. Insertion loss was determined by taking the difference between the sound power with and without the louvers at the termination. Analyses were conducted in the plane wave regime and the acoustic source was anechoic eliminating any reflections from the source. The effect of different louver configurations on insertion loss was examined. Parameters investigated included louver length, angle, and spacing between louvers. Based on the analyses, equations were developed for the insertion loss of unlined louvers.

Microperforated panel (MPP) absorbers are rugged, non-combustible, and do not deteriorate over time. That being the case, they are especially suitable for long term use in harsh environments. However, the acoustic performance is modified when contaminated by dust, dirt, or fluids (i.e. oil, water). This paper examines that effect experimentally and correlates the absorption performance with Maa's theory for micro-perforated panels. Transfer impedance and absorption coefficient are measured for different levels of aluminum oxide and carbon dust accumulation. The amount of dust contamination is quantified by measuring the luminance difference between clean and dirty panels with a light meter. The porosity and hole diameter in Maa's equation are modified to account for dust obstruction. The effect of coating the MPP with oil, water, and other appropriate viscous fluids was also measured. This effect was simulated by modifying the viscous factor in Maa's equation.

The sound attenuation performance of microperforated panels (MPP) with adjoining air cavity is demonstrated. First of all, simulated results are shown based upon Maa's work investigating the parameters which impact MPP performance [1]. It is shown that the most important parameter is the depth of the adjoining cavity. Following this, an experimental study was undertaken to compare the performance of an MPP to that of standard foam. Following this, two strategies to improve the MPP performance are implemented. These include partitioning the air cavity and having a cavity with varying depth. Both strategies show a marked improvement in MPP attenuation.

The objective of this study was to identify and gain an understanding of the origins of noise in a commercial excavator cab. This paper presents the results of two different tests that were used to characterize the vibration and acoustic characteristics of the excavator cab. The first test was done in an effort to characterize the vibration properties of the cab panels and their associated contribution to the noise level inside the cab. The second set, of tests, was designed to address the contribution of the external airborne noise produced by the engine and hydraulic pump to the overall interior noise. This paper describes the test procedures used to obtain the data for the signature analysis, operational deflection shapes (ODS), and sound diagnosis analysis. It also contains a discussion of the analysis results and an inside look into the possible contributors of key frequencies to the interior noise in the excavator cab.

Rear Window Buffeting (RWB) is the low-frequency, high amplitude, sound that occurs in many 4-door vehicles when driven 30-70 mph with one rear window lowered. The goal of this paper is to demonstrate that the mechanisms of RWB are similar to that of sun roof buffeting and to describe the results of several actions suspected in contributing to the severity of RWB. Finally, the results of several experiments are discussed that may lend insight into ways to reduce the severity of this event. A detailed examination of the side airflow patterns of a small Sport Utility Vehicle (SUV) shows these criteria exist on a small SUV, and experiments to modify the SUV airflow pattern to reduce RWB are performed with varying degrees of success. Based on the results of these experiments, design actions are recommended that may result in the reduction of RWB.

This paper describes a study to demonstrate the feasibility of developing an acoustic encapsulation to reduce airborne noise from a commercial diesel engine. First, the various sources of noise from the engine were identified using Nearfield Acoustical Holography (NAH). Detailed NAH measurements were conducted on the four sides of the engine in an engine test cell. The main sources of noise from the engine were ranked and identified within the frequency ranges of interest. Experimental modal analysis was conducted on the oil pan and front cover plate of the engine to reveal correlations of structural vibration results with the data from the NAH. The second phase of the study involved the design and fabrication of the acoustical encapsulation (noise covers) for the engine in a test cell to satisfy the requirements of space, cost and performance constraints. The acoustical materials for the enclosure were selected to meet the frequency and temperature ranges of interest.

The objective of this study was to utilize Statistical Energy Analysis (SEA) to simulate the effects of a variety of noise control treatments on the interior sound pressure level (SPL) of a commercial excavator cab. In addition, the effects of leaks on the SPL of the excavator cab were also investigated. This project was conducted along with various tests that were used to determine the inputs needed to accurately represent the loads that the cab experienced during operation. This paper explains the how the model was constructed, how the loads were applied to the model, the results that were obtained from application of treatments, and a study of the effects of introducing leaks to the cab structure in the SEA model.

The classical methods of measuring acoustic absorption coefficient using an impedance tube and a reverberation chamber are well established [1, 2]. However, these methods are not suitable for in-situ applications. The two in-situ methods; single channel microphone (P- probe) and dual channel acoustic pressure and particle velocity (Pu-probe) methods based on measurement of impulse response functions of the material surface under test, provide considerable advantage in data acquisition, signal processing, ease and mobility of measurement setup. This paper evaluates the measurement techniques of these two in-situ methods and provides results of acoustic absorption coefficient of a commercial artificial Astroturf, a Dow quash material, and a grass surface.

This paper documents an inverse visible element Rayleigh integral (VERI) approach. The VERI is a fast though approximate method for predicting sound radiation that can be used in the place of the boundary element method. This paper extends the method by applying it to the inverse problem where the VERI is used to generate the acoustic transfer matrix relating the velocity on the surface to measurement points. Given measured pressures, the inverse VERI can be used to reconstruct the vibration of a radiating surface. Results from an engine cover and diesel engine indicate that the method can be used to reliably quantify the sound power and also approximate directivity.

As noise concerns for snowmobiles become of greater interest for governing bodies, standards such as SAE J192 are implemented for regulation. Specific to this pass-by noise standard, and unlike many other pass-by tests, multiple non-standardized test surfaces are allowed to be used. Manufacturers must understand how the machines behave during these tests to know how to best improve the measured noise levels. Data is presented that identifies the contributions of different sources for different snowmobiles on various test surface conditions. Adaptive resampling for Doppler removal, frequency response functions and order tracking methods are implemented in order to best understand what components affect the overall measurement during the pass-by noise test.

The objective of this project was to model and study the interior noise in an Off-Highway Truck cab using Statistical Energy Analysis (SEA). The analysis was performed using two different modeling techniques. In the first method, the structural members of the cab were modeled along with the panels and the interior cavity. In the second method, the structural members were not modeled and only the acoustic cavity and panels were modeled. Comparison was done between the model with structural members and without structural members to evaluate the necessity of modeling the structure. Correlation between model prediction of interior sound pressure and test data was performed for eight different load conditions. Power contribution analysis was performed to find dominant paths and 1/3rd octave band frequencies.

Performing acoustic measurements on or near engines, transmissions, as well as in other circumstances where the environment is hazardous and harsh for microphones requires special precautions. Fluids inevitably leak, and the possibility of transducer damage can be very high without proper protection. Properly protecting microphones during testing allows for consistent data quality in these hazardous and difficult environments. While this paper will present the use of a 5 mil Nitrile cover which protects against many fluids within the scope of automotive testing, including water, hydrocarbons, and alcohols, as well as having good heat resistance and high strength, the concepts developed are applicable to other types of microphone protective mechanisms. Acoustic sensitivity was measured and used to calculate the change of the microphone's response after the treatment is applied, as well as after being exposed to various contaminants.

The source in an intake/exhaust system is commonly modeled as a source strength and impedance combination. Both the strength and impedance are normally measured and measurement accuracy depends on selecting an appropriate acoustic load combination. An incident wave decomposition method is proposed which is based on acoustic wave decomposition concepts instead of an electric circuit analogy providing a more straightforward approach to investigating the effect of acoustic load selection. Based on studying wave reflections in the system, the uncertainty for determining source impedance is estimated.

In recent years, Nearfield Acoustical Holography (NAH) has been used to identify stationary vehicle exterior noise sources. However that application has usually been limited to individual components. Since powertrain noise sources are hidden within the engine compartment, it is difficult to use NAH to identify those sources and the associated partial field that combine to create the complete exterior noise field of a motor vehicle. Integrated Nearfield Acoustical Holography (INAH) has been developed to address these concerns: it is described here. The procedure entails sensing the sources inside the engine compartment by using an array of reference microphones, and then calculating the associated partial radiation fields by using NAH. In the second part of this paper, the use of farfield arrays is considered. Several array techniques have previously been applied to identify noise sources on moving vehicles.