Search Results

On-road comparisons were made between a federal reference method mobile emissions laboratory (MEL) and a portable emissions measurement system (PEMS) to support validation of the engine “Not To Exceed” (NTE) emissions design and to evaluate the accuracy of PEMS. Three different brake specific emissions calculation equations (methods) were used as part of this research, with method one directly using engine speed and torque, and methods two and three including ECM fuel consumption and carbon balance fuel consumption. The brake specific NOx emissions for the particular PEMS unit utilized in this program were consistently higher than those for the MEL. The brake specific (bs) NOx NTE deltas were +0.63±0.31 g/kW-h (0.47±0.23 g/hp-h), +0.55±0.17 g/kW-h (0.41±0.13 g/hp-h), and +0.54±0.17g/kW-h (0.40±0.13g/hp-h) for methods one, two, and three respectively.

Low-temperature combustion of diesel fuel was studied in a heavy-duty, single-cylinder, optical engine employing a 15-hole, dual-row, narrow-included-angle nozzle (10 holes × 70° and 5 holes × 35°) with 103-μm-diameter orifices. This nozzle configuration provided the spray targeting necessary to contain the direct-injected diesel fuel within the piston bowl for injection timings as early as 70° before top dead center. Spray-visualization movies, acquired using a high-speed camera, show that impingement of liquid fuel on the piston surface can result when the in-cylinder temperature and density at the time of injection are sufficiently low. Seven single- and two-parameter sweeps around a 4.82-bar gross indicated mean effective pressure load point were performed to map the sensitivity of the combustion and emissions to variations in injection timing, injection pressure, equivalence ratio, simulated exhaust-gas recirculation, intake temperature, intake boost pressure, and load.

Lubricating oil affects the performance of friction materials in transmission, steering and brake systems. The TO-2 Test measured friction retention characteristics of lubricating oils used with sintered bronze friction discs. This paper introduces a new friction performance test for drive train lubricants that will be used to support Caterpillar's new transmission and drive train fluid requirements, TO-4, which measures static and dynamic friction, wear, and energy capacity for six friction materials, and replaces the TO-2 test. The new test device to be introduced is an oil cooled, single-faced clutch in the Link Engineering Co. M1158 Oil/Friction Test Machine.

It is estimated that operating continuously on a B20 fuel containing the current allowable ASTM specification limits for metal impurities in biodiesel could result in a doubling of ash exposure relative to lube-oil-derived ash. The purpose of this study was to determine if a fuel containing metals at the ASTM limits could cause adverse impacts on the performance and durability of diesel emission control systems. An accelerated durability test method was developed to determine the potential impact of these biodiesel impurities. The test program included engine testing with multiple DPF substrate types as well as DOC and SCR catalysts. The results showed no significant degradation in the thermo-mechanical properties of cordierite, aluminum titanate, or silicon carbide DPFs after exposure to 150,000 mile equivalent biodiesel ash and thermal aging. However, exposure of a cordierite DPF to 435,000 mile equivalent aging resulted in a 69% decrease in the thermal shock resistance parameter.

High-efficiency, clean-combustion strategies for heavy-duty diesel engines are critical for meeting stringent emissions regulations and reducing the costs of aftertreatment systems that are currently required to meet these regulations. Results from previous constant-volume combustion-vessel experiments using a single jet of fuel under quiescent conditions have shown that mixing-controlled soot-free combustion (i.e., combustion where soot is not produced) is possible with #2 diesel fuel. These experiments employed small injector-orifice diameters (≺ 150 μm) and high fuel-injection pressures (≻ 200 MPa) at top-dead-center (TDC) temperatures and densities that could be achievable in modern heavy-duty diesel engines.

Fuel is a significant portion of the operating cost for an on-highway diesel engine and fuel economy is important to the economics of shipping most goods in North America. Cat® ACERT™ engine technology is no exception. Ball bearings have been applied to the series turbochargers for the Caterpillar heavy-duty, on-highway diesel truck engines in order to reduce mechanical loss for improved efficiency and lower fuel consumption. Over many years of turbocharger development, much effort has been put into improving the aerodynamic efficiency of the compressor and turbine stages. Over the same span of time, the mechanical bearing losses of a turbocharger have not experienced a significant reduction in power consumption. Most turbochargers continue to use conventional hydrodynamic radial and thrust bearings to support the rotor. While these conventional bearings provide a low cost solution, they do create significant mechanical loss.

Homogeneous charge compression ignition (HCCI) offers the potential for significant improvements in efficiency with a substantial reduction in emissions. However, achieving heavy-duty (HD) HCCI engine operation at practical loads and speeds presents numerous technical challenges. Successful expansion of the HCCI operating range to include the full range of load and speed must be accomplished while maintaining proper combustion phasing, control of maximum cylinder pressure and pressure rise rates, and low emissions of NOx and particulate matter (PM). Significant progress in this endeavour has been made through a collaborative research effort between Caterpillar and ExxonMobil. This paper evaluates fuel effects on HCCI engine operating range and emissions. Test fuels were developed in the gasoline and diesel boiling range covering a broad range of ignition quality, fuel chemistry, and volatility.

Computational fluid dynamic (CFD) simulations that include realistic combustion/emissions chemistry hold the promise of significantly shortening the development time for advanced high-efficiency, low-emission engines. However, significant challenges must be overcome to realize this potential. This paper discusses these challenges in the context of diesel combustion and outlines a technical program based on the use of surrogate fuels that sufficiently emulate the chemical complexity inherent in conventional diesel fuel.

Transport Refrigeration Unit, or TRU, is an example of a diesel emission source that will be regulated in the future. The TRU is used to provide refrigerated space during the transport of fruits, vegetables, meat, pharmaceuticals, beverages, and any other product that needs a temperature controlled environment while being transported. TRUs are used in all modes of transport, on rail cars, on ocean going shipping containers, over the road truck trailers and even on airplane Unit Load Devices. Policy making bodies, understanding the adverse effects of diesel emissions, noise pollution, and fuel consumption have started to pass legislation in an effort to curtail transport diesel emissions. At the local level many states as well as some municipalities have instituted policy designed to eliminate these sources of pollution.

In this paper a model of Trailer Refrigeration Units, TRUs, has been developed to quantify the fuel economy and emissions benefits of alternative power systems. Trailer refrigeration units (TRUs) are refrigeration systems typically powered by a separate diesel engine, and they are used to deliver fresh and frozen food products. The products can be very sensitive to temperature variation and maintaining the proper environment is very important. The diesel engines currently used to power the refrigeration system can contribute to high amount of local emissions at the loading warehouse. A promising future alternative is the use of fuel cell auxiliary power units (APUs). In this paper we have developed a MATLAB/Simulink based modeling of TRUs, and we have used the model to quantify the benefits of alternative power systems. The simulation model consists of an unsteady thermal modeling of TRUs that is coupled to the APU.

The effects of thermal and chemical aging on the performance of cordierite-based and high-porosity mullite-based diesel particulate filters (DPFs), were quantified, particularly their filtration efficiency, pressure drop, and regeneration capability. Both catalyzed and uncatalyzed core-size samples were tested in the lab using a diesel fuel burner and a chemical reactor. The diesel fuel burner generated carbonaceous particulate matter with a pre-specified particle-size distribution, which was loaded in the DPF cores. As the particulate loading evolved, measurements were made for the filtration efficiency and pressure drop across the filter using, respectively, a Scanning Mobility Particle Sizer (SMPS) and a pressure transducer. In a subsequent process and on a different bench system, the regeneration capability was tested by measuring the concentration of CO plus CO2 evolved during the controlled oxidation of the carbonaceous species previously deposited on the DPF samples.

Today's engine and combustion process development is closely related to the intake port layout. Combustion, performance and emissions are coupled to the intensity of turbulence, the quality of mixture formation and the distribution of residual gas, all of which depend on the in-cylinder charge motion, which is mainly determined by the intake port and cylinder head design. Additionally, an increasing level of volumetric efficiency is demanded for a high power output. Most optimization efforts on typical homogeneous charge spark ignition (HCSI) engines have been at low loads because that is all that is required for a vehicle to make it through the FTP cycle. However, due to pumping losses, this is where such engines are least efficient, so it would be good to find strategies to allow the engine to operate at higher loads.

A cooperative program between the DOE Office of Heavy Vehicle Technology and Caterpillar is aimed at demonstrating electric turbo compound technology on a Class 8 truck engine. The goal is to demonstrate the level of fuel efficiency improvement attainable with an electric turbocompound system. The system consists of a turbocharger with an electric motor/generator integrated into the turbo shaft. The generator extracts surplus power at the turbine, and the electricity it produces is used to run a motor mounted on the engine crankshaft, recovering otherwise wasted energy in the exhaust gases. The electric turbocompound system also provides more control flexibility in that the amount of power extracted can be varied. This allows for control of engine boost and thus air/fuel ratio. The paper presents the status of development of an electric turbocompound system for a Caterpillar heavy-duty on-highway truck engine.

HEVs historically have had reduced performance at elevations higher than sea level. The effects of this loss of performance can be mediated with the use of a standard turbocharger; however, approximately 80-90% of the vehicle's operation is at altitudes where full boost from the turbocharger is not needed to maintain performance characteristics comparable to conventional vehicles of the same size. If the turbocharger is used to drive an electric generator, the power produced by the turbine section that is not needed to produce boost in the compressor section of the turbocharger can be used to charge the traction battery of HEVs. The Exhaust Gas Driven Generator converts the thermal energy, normally wasted through the exhaust of the ICE, to electrical energy stored in the traction battery of the HEV.

This paper focuses on the impact of proper thermal integration between two major components of the indirect methanol fuel cell vehicle fuel processor (reformer and burner). The fuel processor uses the steam reformation of methanol to produce the hydrogen required by the fuel cell. Since the steam reformation is an endothermic process, the required thermal energy is supplied by a catalytic burner. The performance of the fuel processor is very strongly influenced by the extent of thermal integration between the reformer and burner. Both components are modeled as a set of CSTRs (Continuous Stirred Tank Reactors) using Matlab/Simulink. The current model assumes no time lag between the methanol sent into the reformer and the methanol sent into the burner to generate the necessary heat for the reformer reactions to occur.

This paper compares the merits of operating a direct-hydrogen fuel cell (DHFC) system using a high-pressure air supply (compressor) versus one using a low-pressure air supply (blower). Overall, for the system modeled, it is shown that there is no inherent performance advantage for either mode of operation at the DHFC stack level. However, in practical applications, as will be shown in this paper, a systems analysis (stack and air supply) of power and efficiency needs to be performed. Equivalent PEM DHFC stack peak power values can be obtained using both high-pressure and low-pressure air supply systems. For each air supply configuration, air mass flow and pressure operating conditions can be found that result in an equal value of the oxygen partial pressure at the cathode catalyst layer surface. However, at the system level, the required air supply power needed to achieve the same DHFC stack performance values can be drastically different for high and low pressure operation.

This work presents a method to maximize the net power output of an indirect methanol PEM fuel cell system. This method establishes an operating strategy for the air supply based on the stack, air supply and water and thermal management (WTM) sub-system characteristics - holding anode conditions constant. It is shown that operating strategies based on individual components result in the inefficient operation of the overall system. Inclusion of the WTM modifies the optimal operating conditions for both low and high pressure systems. However the results for high pressure show an efficiency gain through reducing air pressure and increasing airflow, the opposite of what is expected. This work also outlines the components and issues not included and their importance in system operation.

Vehicle manufacturers claim that fuel cell vehicles are significantly more fuel-efficient and emit fewer emissions than conventional internal combustion engine vehicles /1/. A computer model can help to explore and understand the underlying reasons for this potential improvement. In previous published work, the UC Davis Vehicle Model for the case of a load-following Indirect Methanol Fuel Cell Vehicle (IMFCV) has been introduced and discussed in detail /2/. Because of possible technical barriers with load following vehicles, as well as near term cost issues, hybrid fuel cell vehicle concepts are widely discussed as another fuel cell vehicle option. For load following vehicles, the questions of fast start up and fuel processor dynamics in extreme transient situations, (e.g., during phases of hard acceleration) are not totally resolved at this time. For both of these performance issues, a hybrid design could offer at least an interim solution.

This paper describes two independent studies on γ-alumina as a plasma-activated catalyst. γ-alumina (2.5 - 4.3 wt%) was coated onto the surface of mesoporous silica to determine the importance of aluminum surface coordination on NOx conversion in conjunction with nonthermal plasma. Results indicate that the presence of 5- and 6- fold aluminum coordination sites in γ-alumina could be a significant factor in the NOx reduction process. A second study examined the effect of changing the reducing agent on NOx conversion. Several hydrocarbons were examined including propene, propane, isooctane, methanol, and acetaldehyde. It is demonstrated that methanol was the most effective reducing agent of those tested for a plasma-facilitated reaction over γ-alumina.

Near term (ca. 2005) Fuel Cell Vehicles (FCVs) will primarily utilize Direct-Hydrogen Fuel Cell (DHFC) systems. The primary goal of this study was to provide an analytical basis for including a realistic Compressed Hydrogen Gas (CHG) fuel supply simulation within an existing dynamic DHFC system and vehicle model. The purpose of this paper is to provide a tutorial describing the process of modeling a hydrogen storage system for a fuel cell vehicle. Three topics were investigated to address the delivery characteristics of H2: temperature change (ΔT), non-ideal gas characteristics at high pressures, and the maximum amount of hydrogen available due to the CHG storage tank effective “state-of-charge” (SOC) -- i.e. how much does the pressure drop between the tank and the fuel cell stack reduce the usable H2 in the tank. The Joule-Thomson coefficient provides an answer to the expected ΔT during expansion of the H2 from 5000 psi to 45 psi.