Search Results

Unlike the conventional bleed-air method, using electro-thermal anti-/de-icing methods to completely evaporate all of the supercooled water droplets that collide with the leading edge wing surface of aircraft flying in a freezing environment is not easy in terms of technical feasibility and energy efficiency[1]. If the leading edge is warm enough to stay free from frozen water droplets, the water moves backward while still maintaining the liquid phase. The droplets may freeze somewhere on an unheated surface after being halted for some reason and stick on the surface. Ice gradually accumulates as this process is repeated. Therefore, liquid water must be removed from the surface as soon as possible if the electrothermal method is employed for icing prevention. One answer to this problem is coating the surface with a superhydrophobic paint.

In this paper, emissions reduction technologies applied to high-speed direct injection (HSDI) diesel passenger car engines to meet the stricter exhaust emission legislation are described. To reduce smoke, the F.I.E. has been improved by using a radial-piston distributor pump which delivers fuel-injection-pressure up to 120MPa. Cooled exhaust gas re-circulation (EGR) system and increase in volume ratio of the combustion chamber has made it possible to increase EGR ratio and reduced nitrogen oxides (NOx) and smoke simultaneously. Furthermore, improvements in the oxidation catalyst activating temperature reduces PM at lower exhaust gas temperatures. As a result of applying these technologies, a clean and economical HSDI diesel engine for passenger cars, which complies with Japanese '98 exhaust emissions legislation and has better fuel economy than indirect injection (IDI) diesel engines (above 15%), has been developed.

A new state of the art DOC (Diesel Oxidation Catalyst) having superior light-off and exothermic activity for forced regeneration compared to conventional Pt base passive DOC, was investigated for LDD application. The DOC uses the latest Pt/Pd technology resulting cost effective DPF system. The newly developed DOC demonstrated improved catalytic activities from Pt only DOC in model gas or engine bench tests. In this study, DOC at early development stage showed excellent light-off activity in model gas and engine bench test compared to conventional Pt only DOC, however, it showed “extinction” phenomenon which is one of the deactivation mode while the post injection and it was observed when post injection operation was done at lower DOC inlet temperatures, e.g. below 250 C. Temperature profiles along diameter and length into DOC bed while active regeneration suggested extinction would be caused by fouling of supplied hydrocarbons derived from diesel fuel.

To apply a fuel economy performance to AT&CVT fluid for common use (hereinafter AT/CVT fluid) and manual transmission fluid, by optimizing fluid viscosity, a fundamental study was investigated. Generally, it is well known that the viscosity of polymer-added transmission fluids is gradually reduced, due to deterioration of the viscosity index improver caused by shear stress. An excessive viscosity reduction causes an operation failure or damage to the transmission. Considering above factor, the authors focused attention on the potential of a low viscosity formulation to improve fuel efficiency by reducing an internal stirring-resistance of the transmission. Also from the viewpoint of friction characteristics, the performance of a base oil was studied. Utilizing the EHL (Elast-Hydrodynamic Lubrication) tester [1] and vehicle tests, the performance of base oils was evaluated for the fluid development.

Flows around a forward facing step and a fence are simulated on structured grid to estimate aerodynamic noise by using direct simulation. Calculated results of sound pressure level show quantitatively good agreement with experimental results. To estimate aerodynamic noise from 3D complex geometry, a simplified side mirror model is also calculated. Averaged pressure distribution on the mirror surface as well as pressure fluctuations on the mirror surface and ground are simulated properly. However, calculated result of sound pressure level at a location is about 20dB higher than experiment due to insufficient spatial resolution. To capture the propagation of sound waves, more accuracy seems to be required.

It is well known that tire pressure lower than normal reduces the safety of the vehicle. In consideration of active safety, a new tire pressure warning system for Advanced Safety Vehicle (ASV) has been developed. This involves the four mechanical pressure sensors, a simple structure on each wheel. This system can independently detect pressure of each tire with a high degree of precision under a broad range of vehicle speeds, and requires no adjustment. This paper describes the principle and the performance of this system.

A simple real-time measurement system for the components of volatile organic compounds (VOCs) and polyaromatic hydrocarbons (PAHs) in automobile exhaust gas using a laser ionization method was developed. This method was used to detect VOCs and PAHs in the exhaust gas of a diesel truck while idling, at 60 km/h, and in the Japanese driving mode JE05. As a result, various VOCs and PAHs, such as xylene and naphthalene, were simultaneously detected, and real-time changes in their concentration were obtained at 1 s intervals.

For fuel economy improvement by lean-burn gasoline engines, extension of their lean operation range to higher loads is desirable as more fuel is consumed during acceleration. Urgently needed therefore is development of emission control systems having as high NOx conversion efficiency as three-way catalysts (TWC) even with more frequent lean operation. The authors conducted a study using catalysts loaded with potassium (K) as the only NOx trapping agent in an emission control system of a lean-burn gasoline engine.

The mixture formation by fuel spray impingement (OSKA system) was applied to a small direct-injection diesel engine in order to reduce the wall quenching- induced emissions, i.e., the emissions of THC and soluble organic fractions (SOF). Experiments were carried out using a single-cylinder engine, fitted with various piston cavity geometries, ran under a wide range of compression ratios and fuel injection specifications. The piston cavity was designed as a centrally located reentrant type. The combination of the high squish flow and the weak penetration of the OSKA spray was very effective in reducing harmful emissions. A short ignition delay, under the retarded fuel injection timing, was obtained because of the high compression ratio. The OSKA DI diesel engine showed reduced NOx, smoke, and THC emissions without deterioration of the fuel consumption compared to modern DI diesel engines used in automotive applications.

A new single-brick Ba + alkali metals NOx-Trap catalyst has been developed to replace a two-brick NOx-Trap system containing a downstream three-way catalyst. Major development efforts include: 1) platinum group metals selection for higher HC oxidation with potassium-containing washcoat, 2) alumina and ceria selection, and Rh architecture design for more efficient NOx reduction and 3) NiO to suppress H2S odor. Mitsubishi Motors' 1.8L GDI™ with this Delphi new NOx-Trap catalyst with H2S control achieves J-LEV standard with less cost and lower backpressure compared to the previous model. It is further discovered that incorporation of NiO into the NOx-Trap washcoat is effective for H2S control during sulfur purge but has a negative impact on thermal durability and sulfur resistance. Further study to improve this trade-off has been made and preliminary results of an advanced washcoat design are presented in this paper. Details will be reported in a future publication.

The purpose of this study is to explain the characteristics of homogeneous charge compression ignition. n-Heptane, which has the same cetane number as diesel fuel, was chosen for the fuel. A rapid compression machine was used to clarify the effects of air-fuel ratio, O2 concentration, and compression temperature on ignition delay and NOx emission. These investigations allowed the introduction of a formula for ignition delay.

With society demanding automobiles that provide higher fuel efficiency, safety of occupants in collisions and that at the end of their service life can be recycled with low environmental impact, the steel industry is tackling the needs of the automobile industry by developing ever-higher performance steel materials and simulation technologies that can demonstrate the performance of steel materials at the development stage without the need for costly prototype testing. In this paper, weight reduction of automobile body in Japan will be discussed. The main items will be as follows: (1) Development of Automobile Steel Sheets, (2) Materials for Automobile Bodies, (3) Materials and Technologies (Tailored Blanks, Hydroforming and Locally Quenching) for Reducing the Weight of Panels and Reinforcing members, (4) Future Prospects.

Considerable amounts (400 ∼ 600 thousand tons) of waste vegetable oil in Japan are still flushed down the drain every year. Utilization of waste vegetable oil for diesel fuel leads to two advantages for environmental protection, to reduce CO2 emission from engines and to avoid water pollution of rivers. In this study, combustion characteristics of waste vegetable oil methyl ester (WME) are investigated in detail by not only engine test run but also observation of burning flames in a visual engine. As results indicate, WME shows rather better combustion state in the visual engine and lower smoke emission from a high-speed DI test engine than gas oil. Moreover, by emulsifying WME with water, further improvement of combustion and more than 18 % reduction of NOx emission is carried out.

A method of fatigue life prediction of spot welded joint under multi-axial loads has been developed by fatigue life estimation working groups in the committee on fatigue strength and structural reliability of JSAE. This method is based on the concept of nominal structural stress ( σ ns) proposed by Radaj and Rupp, and improved so that D value is not involved in stress calculation. The result of fatigue life estimation of actual vehicle with nominal structural stress which was calculated through newly developed method had very good correlation with the result of multi-axial loads fatigue test carried out with test piece including high strength steel.

New 440MPa class high-strength steel, which had high r-value(1.6) and elongation(38%), was applied to outer-panel for the first time in the world. In this development FEM simulation was carried out to clarify the necessary steel properties, and the production conditions in strip mill were established. 10-kg weight reduction was realized by using this steel.

In the initial design stage, it is important to discuss what kind of body concept is effective from a viewpoint of environment burden reduction. This paper describes the importance of both weight reduction and recycling through conducting LCA (Life Cycle Assessment) for four kinds of body structures. In addition, using each software, DFMA (Design for Manufacture and Assembly), DFE (Design for Environment) and LCA to parts unit, each effectiveness was discussed through the assessment of the material-hybrid body.

In this paper the fatigue life of welded steel sheet structures is predicted by using FE-Fatigue, which is one of fatigue analysis software tools on the market, and these predicted results are evaluated by reference to corresponding experimental results. Also, we try to predict these structures by using two fatigue life prediction theories established by the JSAE fatigue and reliability committee to compare prediction results. It was confirmed that spot welds fatigue life predictions agree qualitatively with corresponding experimental results and arc welds fatigue life predictions are in good agreement with corresponding experimental results in cases where the SN curve database is modified appropriately.

In order to examine the compatibility of improvement of crashworthiness with weight saving of automobiles by using high strength steel, a combination analysis of Finite Element Method and Dynamic Mechanical Properties has been established. Material properties used in this analysis have been measured by “one bar method” high velocity tensile tests, which can examine the deformation behavior of materials at a bend crush speed range (∼55km/h). It was confirmed that the strength of steel measured by one bar method was raised remarkably after press and hydro forming of high strength steels. It was also confirmed by FEM analysis and load drop test that absorbed energy of bend crush was improved by pre-strain effect. Further, we proved that absorbed energy of bend crush was also improved by appropriate design of thickness and the ratio of bend span and plate length. These effects are applicable to respective high strength steels.

The influence of tensile strength on fatigue strength and the effect of strengthening mechanism on fatigue notch factor were investigated into conventional mild steels, HSLA steels, DP steels and TRIP steels. The grade of studied steels was altered from 440MPa to 780MPa. Not only smooth fatigue specimens with side surface ground and smooth fatigue specimens with laser-cut side surface but also fatigue specimens with a pierced hole were prepared for each of steel sheets. Fatigue tests were conducted in an axial load method. These experiments made it clear that the fatigue limits of smooth specimen increase along the tensile strength approximately independent of strengthening mechanism but those of notched specimen do not necessarily increase along the tensile strength. Namely, fatigue limits of DP steels and TRIP steels with notch increase in proportion to tensile strength although those of HSLA steels with notch do not increase.

For compliance with stringent exhaust emissions regulation, a lot of the world's Heavy Duty Diesel Engines (HDDE) have been recently equipped with electronically controlled components, such as the Fuel Injection Equipment (FIE), Exhaust Gas Recirculation (EGR) system, Variable Geometry Turbocharger (VG). Flexibility of engine control has been increasing more and more with electronic control for low exhaust emissions and good performance. However, determination of the optimum combination of engine control parameters is extremely tedious, because an engine has so many parameters to be optimized and their interactions are complicated. Therefore, a Design of Experiments (DOE) method was used to optimize the engine control parameters, which effect emissions and performance, in a shorter time. After using this method, it was recognized that it was an effective method to optimize various engine parameters, and was very convenient for engine development.