Search Results

Automotive manufacturers are working towards protecting the global environment by using filters to reduce particulate matter (PM) emissions from their vehicles. There is a growing demand for sensors that detect the small amounts of PM leaking through these filters, as they can aid in performing on-board diagnostics (OBD) and monitoring the function of these filters. Currently, vehicles predominantly use an electric resistance type PM sensor, which applies a voltage between electrodes, collects PM, and senses the generation of PM path. However, in response to tightening regulations on PM-OBD, the response time of the sensor needs to be optimized. Furthermore, the fast response time must not degrade the poisoning resistance in order to ensure durability. To shorten sensor response time, we have developed a 20 μm-gap electrode structure using a cross-section of laminated alumina sheets with printed electrodes, which can form PM paths at small PM amounts.

Many ICs are used in various electronic components in automotive applications, such as ECUs (electronic control units) and smart actuators. Automotive ICs required the following features: (1) high integration of analog, digital and output devices; (2) high breakdown voltage for analog devices standing the battery voltage; (3) highly accurate control for analog circuits; (4) susceptibility under harsh operating conditions, such as high ambient temperature and high humidity; and (5) high surge immunity such as ESD (electrostatic discharge) robustness. To meet these requirements, we developed analog and output devices with improved surge endurance based on SOI wafer and trench-dielectric-isolation technologies. Analog circuit applications, especially accurate power management or high-precision solenoid driving, demands stable temperature-compensated output. Load dump and battery-jumping also needs high voltage protection and high noise immunity for these devices.

In Japan, from the viewpoint of ozone layer protection, specified CFCs (Chlorofluorocarbons) phase-out started in 1992 and completed by 1995. HFC-134a (Hydro fluorocarbon-134a) is now dominant in the market. HFC-134a, the replacement, has zero ozone depleting potential, while it still has a higher global warming potential (GWP = 1430). In this paper, efforts of DENSO and the Japanese industry from aspects of refrigerant emission reduction and energy efficiency improvement are introduced.

At present, various efforts are being made in the industrial world to preserve the earth's environment. Automobile industry has to comply with the emission control regulations including NOx and PM and the requirement of reducing CO2 emission from the viewpoint of global warming protection and energy saving. In these situations, diesel engines having a high potential to reduce CO2 emission are attracting much attention. In order to enhance the potential of diesel to reduce CO2 while solving its problems (“slow, dirty, noisy”), common rail systems are vital. DENSO developed an advanced common rail system (CRS) that integrates fuel injectors capable of delivering up to five injection events per combustion cycle at 180MPa injection pressure. This paper describes the injection performance and effects of the 180MPa common rail system and then explains the next generation common rail system.

Increased interest in global warming issues requires rapid improvements in reduction of CO2 emissions. The automotive industry is placing high importance on improving fuel economy performance across their entire product lines. Charging Management System is a necessary element towards fuel economy improvement. Many of today's charging management systems perform at least two important functions: improving efficiency based on vehicle motion, and detecting battery state of charge. These systems become more complicated as more components (i.e. generators, current sensors and ECU) and software are added. Therefore, it is difficult to develop charging management systems for an entire product line and difficult to retrofit the system for vehicles already in production. A stand-alone charging management system solves these issues. This system is independent of the other vehicle systems. The software for improving fuel economy is installed in the generator or current sensor.

In a conventional soldering process, solvents, such as chlorofluorocarbons (CFCs), have been necessary to remove the flux-residue after soldering. A new CFC-free fluxless soldering process has been developed to obtain high sealing ability even in a small soldering area. This new process utilizes a reducing atmosphere with an appropriate load and assembly orientation to solder the parts. Under this fluxless condition, it is found that appropriate loading and good solder-wettability of the upper part increase the wettability of the lower part.

Increasing electric loads in a vehicle causes over-discharge of a battery and drag torque due to an alternator. This paper gives a system concept of vehicle electric power flow management to solve these issues. Its primary function includes preserving electricity in a battery, stabilizing electric bus voltage, interfacing with vehicle torque control system, and improving fuel economy. The key point to realize such a system is a unified structure. It offers ‘Plug and Play’ function for electric power management components. Newly developed Vehicle Electric Power Flow Management System (VEF ) totally controls electric power flow in a vehicle. VEF contains an Electric Power Manager and its functional sub-systems, and controls them with the key parameter ‘electric power’. The sub-system includes Generation, Storage, Conversion, and Distribution to the loads.

The direct injection diesel engine system was developed to solve the problems of conventional diesel engine systems: emissions of PM (Particulate Matter) and high emissions of NOx (nitrogen oxides). The common rail pressure sensor is a key sensor in the system, which requires high-pressure resistance of 160MPa and accuracy of ±1%. This paper discusses our development of a new generation of common rail system high-pressure sensors that are structurally simpler than conventional sensors, while meeting the above requirements.

Spark plugs with higher ignitability are continuously in great demand to realize high fuel efficiency and low emissions. To meet this demand, DENSO launched the Iridium Spark Plug in 1997, which realized the two characteristics that had been conventionally difficult to achieve concurrently-high ignitability and long life. The development of this product was enabled by miniaturizing the center electrode, produced using DENSO's original, highly wear-resistant iridium alloy (featuring a high melting point and excellent oxidation resistance). While spark plugs are now required to have a longer service life, they are also required to be higher in ignitability, as exhaust gas regulations have been tightened recently. However, the effort to miniaturize the center electrode is reaching a limit.

A response surface model of a diesel spray, parameterized by the internal geometries of a nozzle, is established in order to design the nozzle geometries optimally for spray mixing. The explanatory variables are the number of holes, the hole diameter, the inclined angle, the hole length, the hole inlet radius, K-factor and the sac diameter. The model is defined as a full second-order polynomial model including all the first-order interactions of the variables, and a total of 40 sets of numerical simulations based on D-optimal design are carried out to calculate the partial regression coefficients. Partial regression coefficients that deteriorate the estimate accuracy are eliminated by a validation process, so that the estimate accuracy is improved to be ±3% and ±15% for the spray penetration and the spread, respectively. Then, the model is applied to an optimization of the internal geometries for the spray penetration and the spray spread through a multi-objective genetic algorism.

Carbon brushes for automotive starters are used under severe conditions of high electric current density, high contact pressure and high sliding velocity. Therefore lead has traditionally been added to brushes to improve performance and durability. Lead is an environmental hazardous substance. In the EU, the law prohibits adding lead to brushes for electric motors which is installed on new automobiles in and after January 2005. In order to develop the lead free carbon brush for starters, we analyzed the effect and selected substitutive substance of lead. Adding lead to the brush reduces the electric resistance increase of the brush in high-temperature and high-humidity atmosphere and in high-temperature atmosphere. Furthermore lead reduces the wear amount of brush. We developed the lead free brush surpassing the lead addition brush in performance and durability by addition of lead alternatives silver and zinc.

A lot of electric components have been installed in a vehicle today for comfort, safety and environment. This tendency is said to be continued in the future. Therefore, additional power supplies such as exhaust gas electricity generation system and thermal electricity generation system have been developed in the world to supply additional electricity as well as an enlargement of an alternator. However, if these new electricity supply systems are installed in a present electric power system that is controlled based on a voltage feedback, each supply system cannot be controlled effectively, because it is difficult to control output power of each system independently. An electric power based control system, Vehicle Electric power Flow management system (VEF), has been developed to avoid this problem. Sum of required electric power is calculated based on electric loads power and battery charging power. This required power is allocated to each power supply system.

Spray characteristics such as spray shape and spatial distribution of droplet diameter remarkably influences on output and exhaust emissions of direct injection gasoline engines. Especially, spatial distribution of the droplet diameter after impingement of a spray against a piston cavity is one of the most important factors for output and exhaust emissions, but is not revealed sufficiently because of the difficulties of measurement. In this paper, a new laser holography method that can obtain spatial distribution of droplet diameter over the spray in a short time was developed. And with this method, differences of spatial distribution of Sauter mean diameter (SMD) of droplets between before and after impingement on a flat wall in a high-pressure chamber were revealed using a prototype injector. Effects of impinging angle and distance against the wall on spatial SMD distribution were also investigated.

A DPNR (Diesel Particulate-Nox Reduction) system is designed to simultaneously remove PM (Particulate Matter) and NOx from the exhaust of diesel engined vehicles. A DPF (Diesel Particulate Filter) is used in the DPNR system to reduce the PM. The DPF must have high PM filtering efficiency, while at the same time having low back pressure. However, filtering efficiency and back pressure have trade off relations. Therefore, it is necessary to optimize the pore distribution in the walls of the DPF to satisfy both characteristics. This paper will explain that optimized control of pore distribution enables both high PM filtering efficiency and low back pressure.

The challenge for the diesel engines today is to reduce harmful emissions, such as particulate matter (PM) and Nitrogen oxides (NOx), and enhance the fuel efficiency and power, which are its main advantages. To meet this challenge, DENSO has developed an advanced common rail system (CRS) that uses piezo actuated fuel injectors capable of delivering up to five injection events per combustion cycle at 180MPa, currently the world's highest commercially available diesel fuel injection pressure. The DENSO piezo injector incorporates an internally developed piezoelectric element that energizes quicker than its solenoid counterpart, thereby reducing the transition time for the start and end of the fuel injection event. The piezoelectric element and unique passage structure of the DENSO injector combine to provide a highly reliable and responsive fuel injection event.

Conventional methods of physicochemical models require various experts and a high measurement demand to achieve the required model accuracy. With an additional request for faster development time for diagnostic algorithms, this method has reached the limits of economic feasibility. Machine learning algorithms are getting more popular in order to achieve a high model accuracy with an appropriate economical effort and allow to describe complex problems using statistical methods. An important point is the independence from other modelled variables and the exclusive use of sensor data and actuator settings. The concept has already been successfully proven in the field of modelling for exhaust gas aftertreatment sensors. An engine-out nitrogen oxide (NOX) emission sensor model based on polynomial regression was developed, trained, and transferred onto a conventional automotive electronic control unit (ECU) and also proves real-time capability.

In general, automatic braking uses an electric stability control (ESC) hydraulic unit that can automatically increase the hydraulic pressure in the wheel cylinder (hereinafter called wheel pressure), independent of the driver’s braking operation. The hydraulic unit should have sufficient pressure response to apply autonomous emergency braking (AEB). It was necessary for the hydraulic unit to have a high flow rate for the pressure response. To satisfy the performance requirements of the AEB, a brushless motor, which has a high maximum rotational speed and good response, is adopted for the hydraulic unit. Furthermore, sensorless control, which does not require a rotation angle sensor, has been developed so that the motor size can be small and common to conventional units. The developed sensorless control can switch the driving methods in three states: pre-rotation, low speed, and high speed.

Fuel atomization is known as an effective means of reducing the exhaust emissions of internal combustion engines. We have focused on a multiple-hole nozzle as a cost-effective atomization method that does not require any auxiliary devices or an external energy source to carry out atomization. In this report, we will discuss the facts that 1) the primary factors of atomization with the multiple-hole nozzle lie in the flow upstream of the nozzle, and 2) the atomization characteristics such as spray droplet diameter and spray spatial distribution when the factors which effect atomization with the multiple-hole nozzle are changed. As a result, with our newly developed 12-hole nozzle injector in an actual engine, we found an HC reduction effect greater than that of a conventional air-assist injector.

This paper proposes an oil degradation sensor that informs the best time for oil replacement to achieve the right balance with oil conservation and engine protection. We found that free radicals in the engine oil generate by chain decomposition reactions of hydrocarbons by heat and the amount of them increases with an increase in running distance. Based on theoretical analysis and experiment results, the free radical concentrations have high correlations with pH and base number. The sensor using the principle of electron spin resonance (ESR) can measure the amount of free radical molecules in a non-contact method. The sensor successfully detected free radicals produced by the degradation of actual engine oil.

Diesel engines have smoke trade-offs with both NOx and combustion noise. Both the increment of air entrainment into the spray and deceleration of heat release rate slope which become quickly thanks to the increase of air entrainment are effective for overcoming the trade-off between smoke emission and combustion noise. In this study, effect of quick rising injection rate and pre-injection was focused as an enabler for the both. The mechanism of improvement in the trade-off caused by the quick rising injection rate and pre-injection was clarified by analyzing characteristics of spray and combustion, interaction of pre-injected spray to main-injected spray and behavior of smoke emission. Some visualization techniques were adapted to analysis of sprays and combustions. Spray momentum measurement was used for the air entrainment and mixture formation process analyzation.