Search Results

The general benefits of automation are well documented. Order of magnitude improvements are achievable in processing speeds, production rates, and efficiency. Other benefits include improved process consistency (inversely, reduced process variation), reduced waste and energy consumption, and risk reduction to operators. These benefits are especially true for the automation of the aerospace paint removal (or "depaint") processes. Southwest Research Institute® (SwRI®) developed and implemented two systems in the early 1990s for depainting full-body fighter aircraft at Robins Air Force Base (AFB) at Warner Robins, Georgia, and Hill AFB at Ogden, Utah. These systems have been in production use, almost continuously for approximately 20 years, for the depainting of the F-15 Eagle and the F-16 Falcon fighter aircraft, respectively.

A dynamometer test methodology was developed for evaluation of HMMWV axle efficiency with hypoid gearsets, comparing those having various degrees of superfinish versus new production axles as well as used axles removed at depot maintenance. To ensure real-world applicability, a HMMWV variant vehicle model was created and simulated over a peacetime vehicle duty cycle, which was developed to represent a mission scenario. In addition, tractive effort calculations were then used to determine the maximum input torques. The drive cycle developed above was modified into two different profiles having varying degrees of torque variability to determine if the degree of variability would have a significant influence on efficiency in the transient dynamometer tests. Additionally, steady state efficiency performance is measured at four input pinion speeds from 700-2500 rpm, five input torques from 50 - 400 N⋅m, and two sump temperatures, 80°C and 110°C.

There is growing interest in additive manufacturing technologies for prototype if not serial production of complex internal combustion engine components such as cylinder heads and pistons. In support of this general interest the authors undertook an experimental bench test to evaluate opportunities for cooling jacket improvement through geometries made achievable with additive manufacturing. A bench test rig was constructed using electrical heating elements and careful measurement to quantify the impact of various designs in terms of heat flux rate and convective heat transfer coefficients. Five designs were compared to a baseline - a castable rectangular passage. With each design the heat transfer coefficients and heat flux rates were measured at varying heat inputs, flow rates and pressure drops. Four of the five alternative geometries outperformed the baseline case by significant margins.

A recent study of engine sensitivity revealed that spark plugs used in conventional spark-ignited gasoline-fueled engines do not always fire in the intended fashion. Rather than firing to the ground strap during each ignition event, the arc frequently travels to the “rim” or “shell” of the spark plug. This behavior is termed rim-fire and although observed by other researchers in industry, its effects on engine performance are not widely reported. This paper addresses some of the quantitative effects of rim-fire on engine performance. Combustion data were recorded for various repeat conditions on a Ford 1.8L Zetec engine. The first set of engine tests used four, new, conventional, automotive spark plugs. The second set of engine tests used four modified spark plugs that induced 100% rim-fire when the ground strap was permanently removed. The study focused on part- and full-load engine performance, EGR tolerance, and step-transient characteristics.

The Port Fuel Injector (PFI) Deposit Test is a performance-based test procedure developed by the Coordinating Research Council and adopted by state and federal regulatory agencies for fuel qualification in the United States. To date, Southwest Research Institute (SwRI) has performed over 375 PFI tests between 1991 and 1998 for various clients. This paper details the analyses of these tests. Of the 375 tests, 199 were performed as keep-clean tests and 176 were performed as clean-up tests. The following areas of interest are discussed in this paper: Keep-clean versus clean-up test procedures Linearity of deposit formation Injector position effects as related to fouling Dirtyup / cleanup phenomena Seasonal effects This paper draws the conclusion that it is easier to keep new injectors from forming deposits than it is to clean up previously formed deposits. It was found that injector deposit formation is generally non-linear.

A novel urea evaporation and mixing device has been developed to improve the overall performance of a urea-SCR system. The device was tested with a MY2007 Cummins ISB 6.7L diesel engine equipped with an SCR aftertreatment system. Test results show that the device effectively improved the overall NO conversion efficiency of the SCR catalyst over both steady-state and transient engine operating conditions, while NH₃ slip from the catalyst decreased.

The equipment for collecting dilute exhaust samples involves the use of bag materials (i.e., Tedlar®) that emit hydrocarbons that contaminate samples. This study identifies a list of materials and treatments to produce bags that reduce contamination. Based on the average emission rates, baked Tedlar®, Capran® treated with alumina deposition, supercritical CO2 extracted Kynar® and supercritical CO2 extracted Teflon NXT are capable of achieving the target hydrocarbon emission rate of less than 15 ppbC per 30 minutes. CO2 permeation tests were also performed. Tedlar, Capran, Kynar and Teflon NXT showed comparable average permeation rates. Based on the criteria of HC emission performance, changes in measured CO2 concentration, ease of sealing, and ease of surface treatment, none of the four materials could be distinguished from one another.

In-cylinder ion sensing through sparkplug electrodes can be used to determine in-cylinder A/F ratio by using a modified production coil-on-plug ignition system having ion sensing capability. The in-cylinder ionization can be characterized by the height of the peak, location of the peak from ignition command and area under the ionization signal curve. The effects of A/F ratio on the in-cylinder ionization can be isolated from other affecting factors by conducting tests on a constant volume combustion device in which the initial pressure and temperature can be well controlled. This results in a parabolic correlation of the ionization characteristics with the mixture equivalence ratio. Additionally the ionization characteristics show strong dependence on engine load and speed. Equivalence ratio characteristics during engine cranking and warm up are investigated, and a method for on-line calibration of ionization detection is discussed.

A study was performed to develop optimum design strategies for a production V6 engine to maximize catalyst performance at minimum pressure loss and at minimum cost. Test results for an advanced system, designed to meet future emission limits on a production V6 vehicle, are presented based on FTP testing. The on-line pressure loss and temperature data serves to explain the functioning of the catalyst.

Real-time transient and steady-state oil consumption were measured on three SI-engines, applying two different ring-packs to each engine. Testing of multiple engines enables an assessment of the engine-to-engine variability in oil consumption. Testing of multiple ring-packs on each engine enables an assessment of the ring-pack-to-ring-pack variability in oil consumption. The oil consumption was measured by the Southwest Research Institute (SwRI) novel developed SO2-tracer technique, referred to as RTOC-III. An interesting finding is that the testing shows low engine-to-engine and ring-pack-to-ring-pack variability, in both steady-state, as well as in transient oil consumption. This suggests that the RTOC-III system did not introduce significant variability to the data. The testing results are experimental verification of a design and simulation exercise, in a field of scarcely published literature.

The current operation of the International Space Station (ISS) calls for the oxygen used by the occupants to be vented overboard in the form of CO2, after the CO2 is scrubbed from the cabin air. Likewise, H2 produced via electrolysis in the oxygen generator is also vented. NASA is investigating the use of the Sabatier process to combine these two product streams to form water and methane. The water is then used in the oxygen generator, thereby conserving this valuable resource. One of the technical challenges to developing the Sabatier reactor is transferring CO2 from the Carbon Dioxide Removal Assembly (CDRA) to the Sabatier reactor at the required rate, even though the CDRA and the Sabatier reactor operate on different schedules. One possible way to transfer and store CO2 is to use a mechanical compressor and a storage tank.

In off-highway applications the engine torque is distributed between the transmission (propulsion) and other accessories such as power steering, air conditioning and implements. Electronic controls offer the opportunity to more efficiently manage the control of the engine and transmission as an integrated system. This paper deals with development of a steepest descent algorithm for maximizing the efficiency of hydrostatic transmission along with the engine in the presence of accessory load. The methodology is illustrated with an example. The strategy can be extended to the full hydro-mechanical configuration as required. Applications of this approach include adjusting for component wear and intelligent energy management between different accessories for possible size reduction of powertrain components. The potential benefits of this strategy are improved fuel efficiency and operator productivity.

It has been shown within the catalyst industry that the emission performance with higher cell density technology and therefore with higher specific geometric area is improved. The focus of this study was to compare the overall performance of high cell density catalysts, up to 1600cpsi, using a MY 2001 production vehicle with a 4.7ltr.V8 engine. The substrates were configured to be on the edge of the design capability. The goal was to develop cost optimized systems with similar emission and back pressure performance, which meet physical and production requirements. This paper will present the results of a preliminary computer simulation study and the final emission testing of a production vehicle. For the pre-evaluation a numerical simulation model was used to compare the light-off performance of different substrate designs in the cold start portion of the FTP test cycle.

This paper describes the findings of a laboratory effort to demonstrate improved automotive exhaust emission control with a cold-start hydrocarbon collection system. The emission control strategy developed in this study incorporated a zeolite molecular sieve in the exhaust system to collect cold-start hydrocarbons for subsequent release to an active catalytic converter. A prototype emission control system was designed and tested on a gasoline-fueled vehicle. Continuous raw exhaust emission measurements upstream and downstream of the zeolite molecular sieve revealed collection, storage, and release of cold-start hydrocarbons. Federal Test Procedure (FTP) emission results show a 35 percent reduction in hydrocarbons emitted during the cold-transient segment (Bag 1) due to adsorption by the zeolite.

Various fire scenarios involving a hydrogen fuel system were simulated to evaluate their associated safety hazards. Scenarios included finite releases of hydrogen with delayed ignition as well as small hydrogen jet-fire releases. The scenarios tested resulted in minimal damage to the vehicle, minimal hazards to the vehicle's surroundings, and no observable damage or hazards within the passenger compartment.

Forty-eight materials from parts used inside and outside the passenger compartment of six motor vehicles were tested according to FMVSS 302. All samples passed the test although the FMVSS 302 test requirements do not apply to exterior materials. The same materials were also tested in the Cone Calorimeter (ASTM E 1354) at three heat fluxes. The FMVSS 302 performance diagram developed earlier on the basis of Cone Calorimeter data for 18 exterior materials from two vehicles appears to have more general validity for solid plastic parts, regardless whether they are taken from locations inside or outside of the passenger compartment. The previously-developed performance diagram is not applicable to plastic foams and fabrics. Additional criteria are proposed to predict whether a foam or fabric is likely to pass the FMVSS 302 test based on ignition time and peak heat release rate measured in the Cone Calorimeter at a heat flux of 35 kW/m2.

Comparative abuse tests were performed on commercially available 12 V and 36 V battery designs. Four methods were chosen from SAE J2464 standard, Electrical Vehicle Battery Abuse Testing, March 1999, and modified to apply them to typical-sized automotive batteries. The four tests included a Penetration Test, Crush Test, Radiant Heat Test, and Short Circuit Test. Both the 12 V and 36 V batteries showed minimal reactions to the tests, and there was no significant difference between results of the two designs with respect to the abuse tests performed. It should be stressed however, that this project was limited in scope and was not intended to be a thorough investigation in the batteries safety hazards.

Natural gas vehicle (NGV) fuel energy storage density is a key issue, particularly in many heavy-duty applications where compressed natural gas may have unattractively low energy density. For these uses, benefits can be derived by using liquefied natural gas (LNG). From a market perspective, LNG can play a role for transportation because it is available in various areas of the United States and throughout the world. This paper provides a general overview of LNG use for vehicles and specifically an analysis of factors governing the behavior of this cryogenic fluid in a confined vessel. This is intended to provide an understanding of the cause/effect relation between LNG fuel composition, tank heat influx, and rate of fuel usage or storage time.

Due to the serious need of the U.S. Army for a simple and rapid mobile fuel filtration system, a Filtration/Additive Unit (FAU) has been designed and fabricated. The primary use of the FAU is to aid in the cleanup of fuel in Army ground vehicles and equipment fuel cells and storage tanks. The FAU provides a simple and rapid means to remove gross quantities of particulate and water. The unit consists of a trailer-mounted filtration and additive system capable of dispensing three separate additives into the fuel. The FAU was designed to rapidly clean and additive-treat diesel or aviation-type fuels in volumes between 400 and 4500 liters. However, the FAU is capable of processing larger quantities, such as in storage tanks. The designed pump rate is 225 liters per minute (minimum) using diesel fuel at its maximum viscosity (4.1 cSt at 40°C).

The optical spark plug probe and ionization head gasket probe developed at Sandia Laboratories were applied to one cylinder of a production multicylinder automotive gasoline engine. The purpose of this application is to eventually study combustion phenomena leading to high emissions under cold start and cold idle conditions. As a first step in studying cold start combustion and emissions issues, diagnostic instrumentation was simultaneously applied to a production engine under steady state idle, road load and an intermediate load-speed condition. The preliminary application of such instrumentation is the subject of the present paper. The spark plug probe was redesigned for ease of use in production engines and to provide a more robust design. The two probes were geometrically oriented to obtain radial line-up between the optical windows and ionization probes. Data were taken simultaneously with both probes at the three load-speed conditions mentioned above.