Search Results

This paper presents a simulation of the cooling airflow and surface temperatures of a midsize truck. The simulation uses full detailed geometry of the truck. Performance of the under-hood cooling airflow is analyzed and potential design changes leading to better cooling airflow are highlighted. Surface temperature over certain under-hood part is studied. Possible optimizations using various material and configurations are proposed. It is shown that the presented simulation approach provides valuable information to evaluate cooling system and thermal protection performance. Fast design iterations can be achieved using this approach.

Integration of automatic engine Stop/Start systems in “conventional” drivetrains with 12V starters is a relatively cost-effective measure to reduce fuel consumption. Therefore, automatic engine Stop/Start systems are becoming more prevalent and increasing market share of such systems is predicted. A quick, reliable and consistent engine start behavior is essential for customer acceptance of these systems. The launch of the vehicle should not be compromised by the Stop/Start system, which implies that the engine start time and transmission readiness for transmitting torque should occur within the time the driver releases the brake pedal and de-presses the accelerator pedal. Comfort and NVH aspects will continue to play an important role for customer acceptance of these systems. Hence, the engine stop and re-start behavior should be imperceptible to the driver from both a tactile and acoustic standpoint.

One of the remaining challenges in the simulation of the aerodynamics of ground vehicles is the modeling of the airflows around the spinning tires and wheels of the vehicle. As in most advances in the development of simulation capabilities, it is the lack of appropriately detailed and accurate experimental data with which to correlate that holds back the advance of the technology. The flow around the wheels and tires and their interfaces with the vehicle body and the ground is a critical area for the development of automobiles and trucks, not just for aerodynamic forces and moments, and their result on fuel economy and vehicle handling and performance, but also for the airflows and pressures that affect brake cooling, engine cooling airflows, water spray management etc.

A cargo box is a key structure in a pickup truck which is used to hold various items. Therefore, a cargo box must be durable and robust under different ballast conditions when subjected to road load inputs. This paper discusses a Design for Six Sigma (DFSS) approach to improve the durability of cargo box panel in its early development phase. Traditional methods and best practices resulted in multiple iterations without an obvious solution. Hence, DFSS tools were proposed to find a robust and optimum solution. Key control factors/design parameters were identified, and L18 Orthogonal Array was chosen to optimize design using CAE tools. The optimum design selected was the one with the minimum stress level and the least stress variation. This design was confirmed to have significant improvement and robustness compared to the initial design. DFSS identified load paths which helped teams finally come up with integrated shear plate to resolve the durability concern.

The engineering process in the development of commercial vehicles is facing more and more stringent emission regulations while at the same time the market demands for better performance but with lower fuel consumption. The optimization of aerodynamic performance for reduced drag is a key element for achieving related performance targets. Closely related to aerodynamics are wind noise and cabin soiling and both of them are becoming more and more important as a quality criterion in many markets. This paper describes the aerodynamic and aero-acoustic performance evaluation of a Dongfeng heavy truck using digital simulation based on a LBM approach. It includes a study for improving drag within the design of a facelift of the truck. A soiling analysis is performed for each aerodynamic result by calculating the accumulation of particles emitted form the wheels on the cabin. One of the challenges in the development process of trucks is that different cabin types have to be designed.

Long haul tractor design in the future will be challenged by freight efficiency standards and emission legislations. Along with any improvements in aerodynamics, this will also require additional cooling capacity to handle the increased heat rejection from next generation engines, waste heat recovery and exhaust gas recirculation systems. Fan engagement will also have to be minimized under highway conditions to maximize fuel economy. These seemingly contradictory requirements will require design optimization via analysis techniques capable of predicting both the aerodynamic drag and engine cooling airflow accurately. This study builds on previous work [1] using a Lattice Boltzmann based computational method on a Volvo VNL tractor trailer combination. Simulation results are compared to tests conducted at National Research Council (NRC) Canada's wind tunnel.

An important metric in the vehicle brake design process, the cool-down time for a brake disk, strongly influences the durability and reliability of brakes. However, the brake cool-down time is a function of many vehicle and chassis factors, making it time consuming and expensive to evaluate and optimize in hardware testing. In this study, we investigate an alternative approach to hardware testing for evaluating brake design cool-down time by implementing a CFD (Computational Fluid Dynamics) simulation based methodology. The simulation cases were all compared with test data and good agreement was observed between test data and simulation over a wide range of design parameters. It is therefore demonstrated that accurate simulation is a promising new approach to the brake design process.

Interest in natural gas as a fuel for light-duty transportation has increased due to its domestic availability and lower cost relative to gasoline. Natural gas, comprised mainly of methane, has a higher knock resistance than gasoline making it advantageous for high load operation. However, the lower flame speeds of natural gas can cause ignitability issues at part-load operation leading to an increase in the initial flame development process. While port-fuel injection of natural gas can lead to a loss in power density due to the displacement of intake air, injecting natural gas directly into the cylinder can reduce such losses. A study was designed and performed to evaluate the potential of natural gas for use as a light-duty fuel. Steady-state baseline tests were performed on a single-cylinder research engine equipped for port-fuel injection of gasoline and natural gas, as well as centrally mounted direct injection of natural gas.

Brake disc materials are being utilised that have low noise/dust properties, but are sensitive to contamination by surface water. This drives large dust shields, making brake cooling increasingly difficult. However, brake cooling must be delivered without compromising aerodynamic drag and hence CO2 emissions targets. Given that front brake discs sit in a region of geometric, packaging and flow complexity optimization of their performance requires the analysis of thermal, aerodynamic and multi-phase flows. Some of the difficulties inherent in this task would be alleviated if the complete analysis could be performed in the same CAE environment: utilizing common models and the same solver technology. Hence the project described in this paper has sought to develop a CFD method that predicts the amount of contamination (water) that reaches the front brake discs, using a standard commercial code already exploited for both brake disc thermal and aerodynamics analysis.

A validation study was performed comparing the simulation results of the Lattice-Boltzmann Equation (LBE) based flow solver, PowerFLOW®, to cooling cell measurements conducted at Volvo Trucks North America (VTNA). The experimental conditions were reproduced in the simulations including dynamometer cell geometry, fully detailed under-hood, and external tractor geometry. Interactions between the air flow and heat exchangers were modeled through a coupled simulation with the 1D-tool, PowerCOOL™, to solve for engine coolant and charge air temperatures. Predicted temperatures at the entry and exit plane of the radiator and charge-air-cooler were compared to thermocouple measurements. In addition, a detailed flow analysis was performed to highlight regions of fan shroud loss and cooling airflow recirculation. This information was then used to improve cooling performance in a knowledge-based incremental design process.

The accuracy of the Lattice-Boltzmann based simulation method for prediction of aerodynamic drag on a heavy truck was evaluated by comparing results to twenty percent scale model wind tunnel measurements from the University of Washington Aeronautical Laboratory (UWAL). A detailed preproduction Kenworth T2000 tractor trailer was used as the scale model. The results include a comparison of normalized drag between simulation and wind tunnel as well as percentage drag change with the addition of a radius to the rear edge of the trailer. Significant effort was involved to model all of the wind tunnel details affecting the tractor-trailer drag. These are discussed along with the results of additional simulations which were performed to study the impact of the UWAL tunnel geometry relative to a tunnel with the same blockage and constant cross-sectional area, and a case with negligible blockage.

During the design process for a vehicle, the CAD surface geometry becomes available at an early stage so that numerical assessment of aerodynamic performance may accompany the design of the vehicle's shape. Accurate prediction requires open grille models with detailed underhood and underbody geometry with a high level of detail on the upper body surface, such as moldings, trim and parting lines. These details are also needed for aeroacoustics simulations to compute wall-pressure fluctuations, and for thermal management simulations to compute underhood cooling, surface temperatures and heat exchanger effectiveness. This paper presents the results of a significant effort to capitalize on the investment required to build a detailed virtual model of a pickup truck in order to simultaneously assess performance factors for aerodynamics, aeroacoustics and thermal management.

The engineering process in the development of commercial vehicles is facing more and more stringent emission regulations while at the same time the market demands for better performance but with lower fuel consumption and higher reliability. Respective targets require better utilization of existing or even higher engine cooling capacity and optimization of aerodynamic performance for reduced drag. In order to aid on achieving both goals, special attention should be paid on understanding both external and under hood flow structures. This paper describes an optimization study for reducing aerodynamic drag and increasing engine cooling performance conducted on a Light Truck at Jiangling Motors Corporation (JMC). The approach is using simulation based on a LBM solver coupled with a heat exchanger model. Such methodology was used to predict both aerodynamic and cooling characteristics and help highlighting potential areas for improvement.

The importance of fuel economy and emission standards has increased rapidly with high fuel costs and new environmental regulations. This requires analysis techniques capable of designing the next generation long-haul truck to improve both fuel efficiency and cooling. In particular, it is important to have a predictive design tool to assess how exterior design changes impact aerodynamic performance. This study evaluates the use of a Lattice Boltzmann based numerical simulation and the National Research Council (NRC) Canada's wind tunnel to assess aerodynamic drag on a production Volvo VNL tractor-trailer combination. Comparisons are made between the wind tunnel and simulation to understand the influence of wind tunnel conditions on truck aerodynamic performance. The production VNL testing includes a full range of yaw angles to demonstrate the influence of cross wind on aerodynamic drag.

Typical production vehicle development includes road testing of a vehicle towing a trailer to evaluate powertrain thermal performance. In order to correlate tests with simulations, the aerodynamic effects of pulling a trailer behind a vehicle must be estimated. During real world operation a vehicle often encounters cross winds. Therefore, the effects of cross winds on the drag of a vehicle–trailer combination should be taken into account. Improving the accuracy of aerodynamic load prediction for a vehicle-trailer combination should in turn lead to improved simulations and better thermal performance. In order to best simulate conditions for real world trailer towing, a study was performed using reduced scale models of a Sport Utility Vehicle (SUV) and a Pickup Truck (PT) towing a medium size cargo trailer. The scale model vehicle and trailer combinations were tested in a full scale wind tunnel.

Thermal performance of a brake system is one of the key attributes in a new vehicle development process. Adequate brake cooling characteristics are part of the vehicle performance and safety requirements. The design of a new brake system, however, can be a complex task from a thermal engineering perspective, particularly because of complex interactions between the brake component and the rest of the vehicle. Frequently, the vehicle integration issues are the most serious challenges for brake engineers. There are considerations on how much heat should be dissipated from a single and/or consecutive braking events vs. how much cooling can be provided to the brake corner. Design issues such as where to direct the cooling air to how much flexibility is allowed while complying with other requirements from the studio and aero teams. For a brake engineer, the priority is to maximize cooling to the brake corner and prevent system failure.

For a light duty truck, the frame is a structural system and it must go through a series of proving ground events to meet fatigue performance requirement. Nowadays, in order to meet stringent CAFE standards, auto manufacturers are seeking to keep the vehicle weight as light as possible. The weight reduction on the frame is a challenging task as it still needs to maintain the strength, safety, and durability fatigue performance. CAE fatigue simulation is widely used in frame design before the physical proving ground tests are performed. A typical frame durability fatigue analysis includes both the base metal fatigue analysis and seam weld fatigue analysis. Usually the gauges of the frame components are dictated by the seam weld fatigue performance so opportunities for weight reduction may exist in areas away from the welds. One method to reduce frame weight is to cut lightening holes in the areas that have little impact on the frame fatigue performance.

During development of new vehicles, CAE driven optimizations are helpful in achieving the optimal designs. In the early phase of vehicle development there is an opportunity to explore shape changes, gage reduction or alternative materials as enablers to reduce weight. However, in later phases of vehicle development the window of opportunity closes on most of the enablers discussed above. The paper discusses a simplified methodology for reducing the weight in design cycle for truck frames using parametric Design of Experiments (DOE). In body-on-frame vehicles, reducing the weight of the frame in the design cycle without down gaging involves introducing lightening holes or cutouts while still maintaining the fatigue life. It is also known that the lightening holes might cause stress risers and be detrimental to the fatigue life of the component. Thus the ability to identify cutout locations while maintaining the durability performance becomes very critical.

A detailed Design of Experiments (DOE) study is presented to understand the aerodynamic effects of exterior design features and shape parameters of a pick-up truck using Computational Fluid Dynamics (CFD). The goal of the study is to characterize several key design parameters and the interactions between them as related to overall drag of the vehicle. Using this data, the exterior shape is optimized to minimize drag within specified design constraints. An adaptive sampling methodology is also presented that progressively reduces errors in the design response surfaces generated. This combined with a Latin Hypercube based initial design space characterization yields computational efficiency. A trend-predictive meta-model is presented that can be used for early design development. Results from the meta-model are also correlated with experimental data from the wind tunnel.

The Los Angeles City Traffic (LACT) brake test is well known acclaimed procedure used by many vehicle manufacturers to assess the brake pad wear behavior and to investigate the Noise, Vibration and Harness (NVH) performance of the brake system. The LACT driving route consists of a set of real-world driving conditions, which has been considered representative of the US passenger vehicle market. The scope of this study is to mimic the LACT test using finite element analysis (FEA) to calculate the wear displacement based on Rhee’s theory. The Leading-edge and trailing edge of the brake pad’s wear tendency is also predicted from the simulation. The finite element model for wear simulation consists of brake system viz., Rotor, Knuckle, Pads, Anchor bracket, Piston, and Caliper.