Search Results

Over the last two decades, engine research was mainly focused on reducing fuel consumption in view of compliance with more stringent homologation cycles and customer expectations. As it is well known, the objective of overall engine efficiency optimization can be achieved only through the improvement of each element of the efficiency chain, of which mechanical constitutes one of the two key pillars (together with thermodynamics). In this framework, the friction reduction for each mechanical subsystem has been one of the most important topics of modern Diesel engine development. The present paper analyzes the crankshaft potential as contributor to the mechanical efficiency improvement, by investigating the synergistic impact of crankshaft design itself and oil viscosity characteristics (including new ultra-low-viscosity formulations already discussed by the author in [1]).

The paper describes the challenges and results achieved in developing a new high-speed Diesel combustion system capable of exceeding the imaginative threshold of 100 kW/l. High-performance, state-of-art prototype components from automotive diesel technology were provided in order to set-up a single-cylinder research engine demonstrator. Key design parameters were identified in terms boost, engine speed, fuel injection pressure and injector nozzle flow rates. In this regard, an advanced piezo injection system capable of 3000 bar of maximum injection pressure was selected, coupled to a robust base engine featuring ω-shaped combustion bowl and low swirl intake ports. The matching among the above-described elements has been thoroughly examined and experimentally parameterized.

A task group within the SAE Automotive Corrosion and Protection (ACAP) Committee continues to pursue the goal of establishing a standard test method for in-laboratory cosmetic corrosion evaluations of finished aluminum auto body panels. The program is a cooperative effort with OEM, supplier, and consultant participation and is supported in part by USAMP (AMD 309) and the U.S. Department of Energy. Numerous laboratory corrosion test environments have been used to evaluate the performance of painted aluminum closure panels, but correlations between laboratory test results and in-service performance have not been established. The primary objective of this project is to identify an accelerated laboratory test method that correlates with in-service performance. In this paper the type, extent, and chemical nature of cosmetic corrosion observed in the on-vehicle exposures are compared with those from some of the commonly used laboratory tests

When the designer's target is the optimization of a composite system, the analysis of the interactions between the different elements of the system becomes a crucial topic. As a matter of fact, in some cases, the effect of these interactions can become more important than the behavior of each individual component. In the area of fluid power, this problem is very common. In particular the case of hydraulic powered transmission for mobile applications can be considered a paradigm of these problems. This paper presents an original numerical approach to study and design of a hydrostatic transmission: the target is the optimization of the system as a whole, taking into account the characterization and the interaction among all parts. First, the system and the application are presented; the attention is focused on the analysis and modeling of its hydraulic parts (pumps, motors, valves).

In order to increase the efficiency of automotive turbochargers at low speed without compromising the performance at maximum boost conditions, variable geometry compressor (VGC) systems, based on either variable inlet guide vanes or variable geometry diffusers, have been recently considered as a future design option for automotive turbochargers. This work presents a modeling, analysis and optimization study for a Diesel engine equipped with a variable geometry compressor that help understand the potentials of such technology and develop control algorithms for the VGC systems,. A cycle-averaged engine system model, validated on experimental data, is used to predict the most important variables characterizing the intake and exhaust systems (i.e., mass flow rates, pressures, temperatures) and engine performance (i.e., torque, BMEP, volumetric efficiency), in steady-state and transient conditions.

To cope with the increasing number of advanced features (e.g., smart-phone integration and side-blind zone alert.) being deployed in vehicles, automotive manufacturers are designing flexible hardware architectures which can accommodate increasing feature content with as fewer as possible hardware changes so as to keep future costs down. In this paper, we propose a formal and quantitative definition of flexibility, a related methodology and a tool flow aimed at maximizing the flexibility of an automotive hardware architecture with respect to the features that are of greater importance to the designer. We define flexibility as the ability of an architecture to accommodate future changes in features with no changes in hardware (no addition/replacement of processors, buses, or memories). We utilize an optimization framework based on mixed integer linear programming (MILP) which computes the flexibility of the architecture while guaranteeing performance and safety requirements.

Modular instrumentation is being widely used in noise and vibration measurement systems that demand higher channel counts and the wider dynamic range that 24-bit delta-sigma ADCs make available at lower costs. This is an overview how flexible modular instrumentation employing the latest software technology can be used in making high precision noise and vibration measurements where higher sampling rates, higher channel counts, increased dynamic range, and distributed architectures were needed in smaller packages. An example where this is being used is in acoustic beam forming in aircraft pass by noise tests to measure and distinguish engine and airframe noise sources.

The need for improved axle NVH integration has increased significantly in recent years with industry trends toward full-time and automatic four wheel drive (4wd) systems. Along with seamless 4wd operation, quiet performance has become a universal expectation. Axle gear-mesh noise can be transmitted to the vehicle passenger compartment through airborne paths (not discussed in this paper) and structure-borne paths (the focus of this paper.) A variety of mounting configurations are used in an attempt to provide improved axle isolation and reduce structure-borne transmission of gear-mesh noise. The configuration discussed in this paper is a 4-point vertical mount design for an Independent Front Drive Axle (IFDA). A significant benefit of this configuration is improved isolation in the range of drive torques where axle-related NVH issues typically exist.

In the North American automotive market, cylinder deactivation by means of engine valve deactivation is becoming a significant enabler in reducing the Brake Specific Fuel Consumption (BSFC) of large displacement engines. This allows for the continued market competitiveness of large displacement spark ignition (SI) engines that provide exceptional performance with reduced fuel consumption. As an alternative to a major engine redesign, the Active Fuel Management™ (AFM™) system is a lower cost and effective technology that provides improved fuel economy during part-load conditions. Cylinder deactivation is made possible by utilizing innovative new base engine hardware in conjunction with an advanced control system. In the GM 3.9L V-6 Over Head Valve (OHV) engine, the standard hydraulic roller lifters on the engine's right bank are replaced with deactivating hydraulic roller lifters and a manifold assembly of oil control solenoids.

The need for accurate virtual prototyping prediction is well documented in the literature. For welded body structures one notable shortcoming has been the ability for finite element analysis (FEA) to accurately predict the failure of welded joints due to cyclic loading. A new approach to representing spot-welds for durability evaluation in automotive sheet metal structures is presented here. Excellent correlation with spot-weld failures in actual tests have been observed through this modeling approach. We present a method of representing spot-welds using the finite element method. This method has shown to be able of predicting the behavior of spot-welds prior to the build of any prototypes or testing. Further, for spot-weld failures we present evidence that reveals which radial quadrant of the spot-weld will contain the failure. This method also allows engineers to determine the mechanism of failure. This paper describes in detail the spot-weld modeling method.

LIN is a low-cost, low-speed vehicle communication sub-bus becoming increasingly pervasive in automotive subsystems. It is a simple, UART-based master-slave protocol designed as a low-speed supplement to a CAN or FlexRay bus. Its primary application is cabin comfort and human interface hardware such as dashboard controls, power seat harnesses, and power door/window systems. As automotive network designers attempt to reduce wiring complexity and lower system cost, modular, inexpensive sub-buses like LIN become an attractive option. This paper presents an overview of the LIN standard and its applications, and then proposes an architecture for rapid development of LIN networks via hardware simulations of LIN nodes. Using inexpensive, off-the-shelf hardware, LIN sensor and actuator applications can be tested in-place without microcode development, speeding overall network development time.

The unsteady flow fields behind two different automobile outside side rear view mirrors were examined experimentally in order to obtain a comprehensive data base for the validation of the ongoing computational investigation effort to predict the aero-acoustic noise due to the outside rear view mirrors. This study is part of a larger scheme to predict the aero-acoustic noise due to various external components in vehicles. To aid with the characterization of this complex flow field, mean and unsteady surface pressure measurements were undertaken in the wake of two mirror models. Velocity measurements with particle image velocimetry were also conducted to develop the mean velocity field of the wake. Two full-scale mirror models with distinctive geometrical features were investigated.

FlexRay is a new networking protocol for embedded electronics. Technology using FlexRay provides improved throughput, determinism, and redundancy relative to existing designs using the Controller Area Network (CAN) protocol. Two criticisms of FlexRay are its increased cost and complexity compared to CAN. Although the cost will be reduced over time as usage goes up, the complexity issue is a problem of perception to some extent. This paper presents an example network design for CAN, and then adds network frames such that the throughput of CAN is exceeded. Next the paper describes how the example network design can be transitioned to FlexRay. The transition applies design practices used with CAN to reduce the complexity of FlexRay.

Hardware-in-the-loop (HIL) simulation has become standard practice in the verification process of electronic control units (ECUs). However, new system control concepts continue to drive and expand the requirements for HIL systems. In this maturing application space, there is a natural trend towards the use of commercial-off-the-shelf (COTS) tools and open, multivendor hardware architectures. This open architecture is critical in helping HIL testers meet these requirements in an increasingly cost effective and higher performance manner. Multicore processors today offer performance and flexibility on a scalable computing platform, which furthers this COTS trend. Computer platforms like desktop PCs, CompactPCI and PXI [ 1 ] (CompactPCI eXtensions for Instrumentation) deliver high-performance systems that allow for the leveraging of multicore processor capabilities in achieving highly realistic plant simulations for controller testing.

Efficient methods for simulating operators performing part handling tasks in manufacturing plants are needed. The simulation of part handling motions is an important step towards the implementation of virtual manufacturing for the purpose of improving worker productivity and reducing injuries in the workplace. However, industrial assembly tasks are often complex and involve multiple interactions between workers and their environment. The purpose of this paper is to present a series of industrial simulations using the Human Motion Simulation Framework developed at the University of Michigan. Three automotive assembly operations spanning scenarios, such as small and large parts, tool use, walking, re-grasping, reaching inside a vehicle, etc. were selected.

ECU designers are seeking more flexibility from HIL test systems. Often their needs are met by the development of custom hardware, either internally or by HIL test system vendors. Many systems also rely heavily on the use of multiple expensive microprocessors to achieve the required timing and synchronization performance. This paper discusses an alternative based on PC technology and reconfigurable I/O hardware. The HIL test system designer uses a graphical programming interface to reconfigure not only the real-time software portion of the system, but also the FPGA-based I/O hardware. This increases flexibility and lowers cost by providing capabilities such as generating simulated outputs synchronized to crank angle and implementing multiple serial communication protocols.

Fast-running metamodels (surrogates or response surfaces) that approximate multivariate input/output relationships of time-consuming CAE simulations facilitate effective design trade-offs and optimizations in the vehicle development process. While the cross-validated nonparametric metamodeling methods are capable of capturing the highly nonlinear input/output relationships, it is crucial to ensure the adequacy of the metamodel error estimates. Moreover, in order to circumvent the so-called curse-of-dimensionality in constructing any nonlinear multivariate metamodels from a realistic number of expensive simulations, it is necessary to reliably eliminate insignificant inputs and consequently reduce the metamodel prediction error by focusing on major contributors. This paper presents a robust data-adaptive nonparametric metamodeling procedure that combines a convergent variable screening process with a robust 2-level error assessment strategy to achieve better metamodel accuracy.

With the abundance of electronic devices and sensors in automotive technology, it has become increasingly important to establish efficient, cost-effective device validation methods for CAN, J1939, and GMLAN. An easy method of validation is simultaneous sampling of multiple measurements for comparison. For instance, if you have an ECU that receives inputs using CAN, and controls analog outputs, you can measure both CAN and analog data to verify that the ECU algorithm is behaving properly. This paper will discuss techniques for sharing timing and triggering signals between CAN, analog, and digital hardware to prevent clock drift and start latencies and reduce operating system jitter. We will cover techniques to use a common clock to drive multiple boards and specify events to trigger multiple board acquisitions. Timing and triggering signals can be shared in a PC through timing and triggering cables or in PXI through the PXI Trigger bus in the backplane.

Sixteen participants aged 55–65yrs provided deBoer scale ratings of discomfort glare for a vehicle with horizontally swiveling HID headlamps and a vehicle with the same headlamps that did not swivel in eight scenarios staged in a darkened parking lot. Participants, who were seated in the driver’s position of a stationary vehicle and instructed when to look, viewed the oncoming test vehicles in scenarios of 180m left turn, 180m right turn, 80m left turn, 80m right turn, left turn beside participant vehicle, crossing left in front of participant vehicle, right turn beside participant vehicle, and straightaway, in counterbalanced presentation orders. The swiveling headlamp vehicle provided statistically lower glare ratings in both 180m curves and the 80m right curve and statistically lower or similar in the intersection scenarios than the fixed headlamp vehicle.

Twent-two participants of varying ages detected roadside targets in two consecutive dynamic evaluations of a horizontally swiveling headlamp vehicle and a vehicle with the same headlamps that did not swivel. Participants detected targets as they drove unlighted low-speed public roads. Scenarios encountered were intersection turns, and curves with approximate radii of 70-90m, 120-140m, 170-190m, and 215-220m. Results from the first study found improved detection distances from the swiveling headlamps in left curves, but unexpectedly decreased detection distances in larger radius right hand curves. The swiveling algorithm was altered for the second study, and the headlamps used did not have the same beam pattern as in the first study. Results from the second study again found improved detection distances from the swiveling headlamps while in the larger radius right hand curves fixed and swivel were not statistically different.