Search Results

Nowadays, electromagnetic compatibility (EMC) has taken an important role in automotive development. This is because the effects that EMC can cause in a vehicle or on the environment. All systems contained in a vehicle emit EMC, and can be influenced by it also. During the vehicle design phase some variables have to be considered and improved to make the vehicle to be electromagnetic compatible. We can list the vehicle systems as electromagnetic generators or victims, as below: Generators: Ignition GPS transmission system Mobile phone transmission system Electrical motors Radars Power modules Victims: Sensors Cables Control modules (BCM, ECM, etc.) An example of a complete system subject to the EM effects is the X-by-wire (or drive-by-wire) system, where mechanical systems are substituted by modules, cables, sensors, actuators. This system has to be designed considering electromagnetic compatibility.

In the last decades, there has been an increasing demand for vehicle noise control and, at the same time, fuel economy has become critical for the automotive industry. Therefore, a precise balance between performance and mass of sound package components is essential. In this work the original dash insulation system of an automotive vehicle was replaced by a lightweight alternative. The methodology of Statistical Energy Analysis (SEA) was employed to design multilayered fibrous constructions for engine noise control. The results were verified through experimental testing and supported the achievement of vehicle requirements regarding comfort, weight and environment.

Noise generated during tire/road interaction has significant impact on the acoustic comfort of a vehicle. One of the most common approaches to attenuate road noise levels consists on the addition of mass treatments to the vehicle panels. However, the acoustic performance of sealing elements is also relevant and has an important contribution to the noise transmission into the vehicle interior. In this paper the correct balance between the mass added to treat vehicle panels and sealing content is investigated. The procedure to quantify the critical road noise transmission paths consists of recording interior noise levels as applied treatment is removed from potential weak areas, such as wheelhouses, floor, doors and body pillars. It is observed that the noise propagation through body pillars has a direct influence on road noise levels.

According to several customer perception survey, Squeak and Rattle (S&R) is among the top most annoying defects. Consequently, GMB engineering design, development and validation process must be continuously improved and consistently applied to all platforms to guarantee that all products are free from squeaks and rattles. This paper introduces those concepts and discusses some strategies to eliminate or minimize S&R. Concepts and tests results are commented. Finally, the challenge in detection and analysis of S&R is discussed. Objective and subjective evaluation methodologies are being developed and suppliers training and integration have been improved

The purpose of the theme developed in this work is to increase the volume of information related to vehicle evaluation and how human perception can be translated into numbers, thus facilitating the process of definitions, refinement and analysis of its performance. Based on the discipline of psychophysics, where it is possible to study the relationship between stimulus and sensation and the use of post processing tool known as PSD (Power Spectral Density), post process the acceleration data of inputs perceived by the occupants of the vehicle, when driving in routes considered ergodic. By this, in a summarized way, get to human subjective perception of comfort. This material shows in a conceptual way a sequence of studies that were conducted to make it possible, to generate a performance classification of the subjective vehicle attribute of Smoothness, by processing values of acceleration measured the driver's seat.

The control of noise and vibrations using conventional damping materials is typically associated to mass penalties in a vehicle. A lightweight alternative employs piezoceramic materials connected in series to a resistor and an inductor (R-L circuit) to perform as mechanical vibration absorber, called piezoelectric resonator. In this paper, piezoelectric resonators are designed to attenuate vibration in a vehicle panel. The choice of design parameters, such as correct placement for the piezoelectric patches and the optimal electrical circuit values, is assisted by Finite Element simulation (FE) and theoretical analysis. Measurements of Sound Transmission Loss (STL) and modal analyses are conducted to demonstrate the efficiency of the proposed technique when compared to a conventional damping material.

Through computational dynamic simulations is possible to achieve high reliability index in the development of automotive components, thereby enabling the reduction of cost and time of a product development with considerable gain in quality. This work suggests the validation of a methodology for simulation where is possible to improve the confidence level for design flexible components, such Heater and Cooling hoses that are under dynamic engine action, in relation to the physical model. Known the difficulty in predicting non-linear mathematical relationship deformation under effect of forces and moments, was established a study based on experimental measurements where were used as input parameters to simulate the dynamic behavior of flexible components, in this case, coolant hoses.

In order to illustrate the constant development of the automatic transmission controls area, this paper describes how the garage shift calibration works in vehicles with transverse front wheel drive powertrains. A garage shift (GS) is the turbine speed transient commanded by the shift lever movement from Park to Drive or Reverse, from Neutral to Drive or Reverse, from Drive to Reverse, from Reverse to Drive, or from Drive or Reverse to Neutral [1]. A usual metric to verify the garage shift comfort is the data acquisition of the fore-aft acceleration on the seat track, but also the shift time should be considered, as well as the clutch energy and the repeatability of the shift feeling for different temperatures and engine idle speed levels. This paper demonstrates the transmission calibration strategies to determine a sensitive and a non-sensitive garage shift and its interactions with the engine calibration.

Acoustics, in a broad sense, is an essential product attribute in the automotive industry, therefore, it is relevant to study and compare theoretical and numerical predictions to experimental acoustic measurements, key elements of many acoustic development processes. The numerical methods used in the industry for acoustic predictions are widely used for exhaust system optimization. However, the numerical and theoretical predictions very often differ from experimental results, due to modeling simplifications, temperature variations (which have high influence on speed of sound), manufacturing variations in prototype parts among others. This article aims to demonstrate the relevant steps for acoustics development applied in automotive exhaust systems and present a comparative study between experimental tests and computer simulations results for each process. The exhaust system chosen for this development was intended for a popular car 4-cylinder 1.0-liter engine.

Drive a vehicle through corners is a very complex activity, since it means change of movement states. Considering a typical corner, the driver starts in a transient state, changes to a steady state and again changes to transient. Those variations make the vehicle change its behavior due specific suspension and steering characteristics. The idea of this paper is show how only one of those characteristics, the understeer gradient, have influence in the stability perception of the driver. The focus is show how the understeer gradient variation can induce perception of low stability in vehicle when cornering no matter the vehicle still keeps its correct path. This variation means an understeer gradient “acceleration”, the metric human being can perceive, in other words the feeling of stability or its lack of.

Vehicular manual transmissions systems often use a vent or breather to allow pressure control inside the main structure. This pressure variation comes along with differences caused by working temperature range. However along with air flow these vents may occasionally allow oil passage noticed by vehicle owner as a transmission leakage event. The more sophisticated the more expensive is the venting device which may contain membranes, labyrinths, baffles and other solutions to avoid leakage. The purpose of this paper is to present a simplified solution to avoid transmission fluid leakage by combining a regular sealing device (fiber concept gasket) and a baffle to avoid oil splash to reach the venting device. The proposed concept took into consideration a quick implementation aspect, low financial impact and less complexity to the overall current system modifying an existing component by adding secondary function instead of creating additional components.

It is known acoustic comfort is a key feature to meet customer expectations for many products. In the current automotive industry, vehicle interior quietness is seen as one of the most important product attributes regarding perceived quality. A quiet interior can be achieved through an appropriate balance of noise sources levels and acoustic materials. However, the choice of the most efficient acoustic content may be challenging under severe cost and mass restraints commonly found in emerging market vehicles. Therefore, it is fundamental to develop efficient materials which will provide high acoustic performance with lower weight and cost. In this paper the fine tuning of the headliner structure is presented as an efficient way to increase acoustic performance. Structures currently employed for this vehicle subsystem are described. Airflow resistance and sound absorption measurements are used to guide development and make precise manufacturing process changes.

Product Design is a process of creating new product by an organization or business entity for its customer. Being part of a stage in a product life cycle, it is very important that the highest level of effort is being put in the stage. The Design for Six Sigma (DFSS) methodology consists of a collection of tools, needs-gathering, engineering, statistical methods, and best practices that find use in product development. DFSS has the objective of determining the needs of customers and the business, and driving those needs into the product solution so created. In this paper the DFSS methodology is employed to develop the optimal solution to enhance sound transmission loss in a vehicle front of dash pass-through. An integrated approach using acoustic holography and beamforming Noise Source Identification (NSI) techniques is presented as a manner to improve sound insulation during vehicle development.

Microphone array based techniques have a growing range of applications in the vehicle development process. This paper evaluates the use of Spherical Beamforming (SB) to investigate the transmission of wind-generated noise into the passenger cabin, as one of the alternative ways to perform in-vehicle troubleshooting and design optimization. On track measurements at dominant wind noise conditions are taken with the spherical microphone array positioned at the front passenger head location. Experimental diligence and careful processing necessary to enable concise conclusions are briefly described. The application of Spherical Harmonics Angularly Resolved Pressure (SHARP) and the Filter-And-Sum (FAS) algorithms is compared. Data analysis variables, run-to-run repeatability and system capability to identify design modifications are studied.