Search Results

The Advanced ECS is under development for the purpose of saving fuel, improving safety, and cabin comfort. In FY2006 study, basic components (i.e. MDC, OBNOGS, desiccant units, and CO2 removers) have been improved and their performances evaluated including resistance to environmental condition (i.e. vibration). In addition, the suitable system configuration for a 90-seats aircraft has been considered to evaluate the feasibility of the system. In this paper, we show the results of the evaluated performances based on prototype components, and the analytical study of a revised system configuration.

In response to design requirements for lower weight and higher output, the motorcycle engine cylinder block has evolved from a cast cylinder block to an aluminum alloy cylinder block whose bore walls are surface-treated for wear-resistance. Hard-chromium plating, nickel-compound plating, and the like are in wide use as the wear-resistance surface treatment method, but spray technology has recently been attracting attention because of less impact on the environment, superior initial running-in performance and good oil retention. We have been applying a unique spraying method called wire explosion spraying to those models with a special need for wear-resistance surface. In this report we describe our wire explosion spray technology. With the aim of improving the bond strength of the sprayed coat, we studied the effects of the collided particles' form on bond strength in the wire explosion spraying conditions.

This paper describes a numerical analysis method for predicting the brake squeal using the Substructure Synthesis Method. This method is more accurate than the classical method based on the mass-spring system, and simpler than the analysis of all the brake system by FEM. The squeal studied here is focused the one occurring in the low frequency range and its mechanism is due the structural instability of the brake assembly. First, some experiments were carried out in order to grasp the brake squeal phenomenon. These experiments made clear the following items. (1) The low frequency brake squeal occurred at 850Hz. (2) The vibration mode shape had 5 nodes fixed in a space. (3) The brake squeal became maximum at 0.3 - 0.5 (MPa) liquid pressure under the constant temperature condition. (4) The higher the temperature of the pad was, the stronger the brake squeal was under the constant liquid pressure condition.

Motorcycle engines are operated at an extremely broad range of revolutions, from 1000 min-1 to 10000 min-1 or more. Ideally, the natural frequency of each part should never match the engine excitation frequency at any point over that entire range of revolution speeds, but practically, there are times when resonance cannot be avoided because the range is so broad, and therefore the vibration amplitude at resonance must be kept low. For this reason, it is important to grasp not only the resonance frequency but also the vibration amplitude at that point. This may be achieved by two methods, measurement and analysis. The direct measurement of vibration is generally difficult because the motorcycle muffler system has a complex shape and in addition it gets very high temperature when the engine is operating. For this reason, with the aim of being able to predict muffler vibration at the design stage, we carried out a vibration test and FEM (finite element method) analysis.

In the expansion of composite material application, it is one of the most important subjects in assembly of aircraft structure how drilling of composite/metal stack should be processed in an efficient way. This paper will show the result of development of a drill bit for CFRP/Aluminum-alloy stack by Kawasaki Heavy Industries (KHI) and Sumitomo Electric Hardmetal (SEH). In order to improve workability and economic performance, the drill bit which enables drilling CFRP/Al-alloy stack: at 1 shot; from both directions; without air blow and coolant (just usual vacuuming); was required. A best mix drill bit which has smooth multi angles edge and pointed finishing edge was produced as a result of some trials. Developed drill bit achieved required performance and contributed to large cost reduction, labor hour saving, production speed increase and work environment improvement.

In this study, we efficiently predict the vibration response of a design shape at a low computational cost in the early development stage, select design proposals with good characteristics from many proposals devised by the designer at the early stage, and forward them to the next stage to achieve the front-loading of development while increasing product value. The application of participation factor (PF) focusing on the response at a specific part for vibration evaluation of a motorcycle frame is described. To reduce the motorcycle frame vibration, an eigenvalue analysis was performed, and appropriate design change proposals were efficiently selected using partial participation factor (PPF), an index showing the relevance of vibration of specific parts or positions. Using the PPF, we extracted which vibration modes considerably contribute to the vibration response of the part of interest.

In the closed environments such as manned space station, it is necessary to remove contaminant gas to keep a suitable environment. Removal of gaseous contaminants generated from crew, animals, and plants is important function to keep the environment below the allowable level in the Closed Ecology Experiment Facilities (abbreviated as CEEF). CEEF consist of three modules for habitat, animal and plant, the supporting facilities for each module and a plant cultivation facility. CEEF are scheduled to be constructed from 1994 in Aomori Prefecture, northern part of Japan. For designing Trace Contaminant Control Assembly (TCCA) for CEEF, the following six (6) trace contaminants have been selected as major contaminant gas in CEEF; Ammonia (NH3) Methane (CH4) Ethylene (C2H4) Carbon Monoxide (CO) Nitrogen Dioxide (NO2) Sulfur Dioxide (SO2) Ethylene is well-known as an aggressive contaminant to plant growth and maturity.

The engine noise accounts for a relatively large percentage among the noises generated by a motorcycle. Among the parts of the engine, the cover is important in design as well as a source of the engine noise, being at the end of the vibration transfer path. This paper clarifies that the natural frequency of the cover with a flat surface clearly affects its vibration and noise radiation and that its vibration depends on this surface, by investigation of the effect of surface shape of the cover on its vibration and noise radiation and by a modal analysis of its vibration characteristics. In addition, we confirmed that the calculated value of the radiated noise from the cover agrees well with the measured value.

In the closed environments, removal of trace contaminants generated from persons, animals, and plants is important function to keep the environment below the allowable level. We conducted the fundamental tests in order to confirm design of TCCA (Trace Contaminants Control Assembly) for Closed Ecology Experiment Facilities (CEEF), and obtained the following results; 1) The palladium-on-alumina catalyst is suitable for CO, CH4, C2H4 conversion at temperature lower than 400°C. 2) The alkali impregnated AC (activated charcoal) is effective for NO2, SO2 removal and prevents catalyst poisoning from SO2. 3) The active-desorbing conducted by hot air blow-throw an AC is effective for C2H5OH, CH2Cl2 desorbing. We discuss the fundamental test and design conditions for TCCA.

A Temperature and Humidity Control (THC) assembly an essential system in order to provide comfortable environment for crew members in Japanese Experiment Module (JEM). Development of an engineering model (EM) and a proto model (PM) of JEM THC assembly started from March 1991 and completed on March 1995 successfully. In this development phase, it is called JEM EM phase, qualification test of THC was conducted to verify the THC design. This paper presents JEM THC design and an outline of the assembly model development.

In order to improve the fuel efficiency and the operating performance of motorcycles, there is a need to reduce their weight. Magnesium, which is the lightest of the various metals currently being used and has a high specific strength, has the potential to satisfy that need. We conducted a study to clarify the weldability and strength characteristics of, and the most suitable surface treatment for, extruded magnesium alloys and rolled magnesium alloys. Based on the stress analysis by the finite element method, we designed a magnesium swing arm and produced the prototype swing arm by pressing hot rolled AZ31 magnesium alloy plates and welding them. The prototype is about 10% lighter and has higher torsional rigidity than a conventional aluminum swing arm.

A new 0.9-liter 4-valve-per-cylinder liquid cooled engine was developed for 1984 model motorcycles. This new engine was optimized from the standpoint of performance, durability, and weight efficiency. Semi-Flat slide carburetors, high compression ratio, relatively short stroke and large valves were employed. This engine was upgraded every other year with changes in displacement. Induction system, exhaust system, and valve train. This paper describes, from the viewpoint of the designer, the evolution of the 4-valve liquid-cooled engine from the 1984 to 1988 models. In that evolutionary process we employed: (1) semi-down draft carburetors with smooth air ducts, (2) a computer-aided intake and exhaust port design and manufacturing system. (3) individual rocker arms. (4) a cool air intake system. (5) lightweight pistons. (6) angle -controlled tightening of connecting rod bolts.

In the modern aircraft manufacturing, the cost reduction, the manufacturing time reduction, and the weight saving of aircraft are strongly demanded. The Refill Friction Spot Joining [1,2](FSJ, in other words FSSW, Friction Stir Spot Welding), which is one of innovative solid-state joining methodologies based on the Friction Stir Welding[3], is a promising technology that can replace rivets and fasteners. This technology is expected to offer cost reduction and weight saving for the aircraft manufacturing. In this study, to make stronger and reliable joints, the shoulder-plunging process of Refill FSJ was employed. The weldability of the Alodine or Chromic Acid Anodize coated materials along with a faying-surface sealant was investigated. The joint properties, such as tensile shear strengths and corrosion resistance, were evaluated.

This paper describes the predicted results of acoustic transmission loss (T.L.) for a motorcycle muffler. First, the T.L. of a prototype muffler with one expansion chamber was obtained by measuring sound levels at the inlet and outlet ports of the muffler by speaker test. T.L. was then calculated by using a three-dimensional Finite-Element Method (FEM) for acoustic fields in the muffler. There was good coincidence between the calculated T.L. and experimentally observed data. Second, T.L. of the prototype muffler while attached to a motorcycle engine was measured. On this step, however, a similarly calculated T.L. using FEM to consider the effect of exhaust gas temperature in the muffler showed differences from the measured one. It was estimated that muffler body vibration sounds may affect the result. A dynamic analysis of the structure was carried out using FEM to obtain the eigen modes of the muffler body.

With an increasing number of vehicles, the reduction of traffic noise emissions becomes a greater social requirement. On the other hand, as users' tastes for motorcycles have diversified, it becomes important to develop and supply products to meet customers' requests within a short period. Therefore, it is a key factor to efficiently develop motorcycles which conform to the noise regulations. This paper describes concrete examples of currently utilized noise-source proving methods and noise reduction methods for motorcycles.

The rocker arm has a function to lead the cam shaft rotation to the valve operation. There are cases when damages are caused due to abnormal wear at the sliding part, causing certain problems. Authors classified the wear phenomenon, and realized a systematic analysis on the possible cause of the damage. As a result, it was revealed that the damage was of two types, and to prevent the hard wear, it is effective to apply shot peening before plating. The prototype rocker arm was test under various lubricating conditions, thus actually confirming that the occurrence of wear was largely reduced.

As for automobile, the mass production period of Electric Vehicle(EV) has begun by the rapid progress of the battery performance. But for EV-Motorcycle(MC), it is limited for the venture companies' releases. The design and evaluation methodologies are not yet established or standardized so far. This paper provides the practical and the experimental examples. To study the feasibility of EV-MC, we developed the prototypes in the present technical and suppliers' parts environments, and evaluated them by the practical view of the MC usage. The developed EV-MC has the equivalent driving performance of the 250cc internal combustion engine(ICE)-MC and a cruising range of 100km in normal use.

Electroimpact and Kawasaki Heavy Industries (KHI) have produced a new riveting process for the forming of Briles type rivets in Boeing 777 and 777X fuselage assemblies. The Briles rivet is typically used for fuselage assembly and is unique in that it has a self-sealing head. Unlike conventional headed rivets such as the NAS1079, this fastener does not require aircraft sealant under the head to be fluid tight. This unique fastener makes for a difficult fastening process due to the fact that interference must be maintained between the hole and fastener shank, as well as along the sides of the fastener head. Common issues with the formed fasteners include gapping under the fastener head and along the shank of the fastener. Electroimpact has employed a host of different technologies to combat these issues with Briles fastening. First, Electroimpact’s patented “Air Gap” system allows the machine to confirm that the head of the rivet is fully seated in the countersink prior to forming.

In line with the increase in the output of motorcycle engines, there has been an increase in incidents of the seizure between shift fork and gear because of the increased thrust force. We designed a test method that uses actual shift forks to simulate actual sliding conditions, then used that test method to evaluate the feature of the shift fork sliding and the different shift fork surface treatments. The shift fork slid against the gear not as surface contact but as tilted contact. We selected the candidates from the view that the surface treatment of the shift fork contact surface to give it higher seizure resistance when in tilted contact is required. We evaluated chromium nitride thin film, diamond-like carbon thin film, molybdenum sprayed coating, and sulphonitriding, and molybdenum sprayed coating exhibited the highest seizure resistance. The conformability plays a significant role in the sliding between the shift fork and the gear.

The quality of exhaust sound has become one of the important factors in the motorcycle market. Therefore both an efficient sound quality evaluation method and technology to achieve ideal sound quality have become necessary. Sound qualify evaluation has generally been performed by trial and error through repeated modification of exhaust silencer construction until desired quality was obtained. But it usually took painstaking work and long hours. In order to solve such problems, we established an objective auditory evaluation method. We also applied Principal component analysis to analize the result of the “Semantic Differential Method (SD method)” so as to determine the affecting elements. Through this analysis system, “powerful sound” caused by relatively higher content of the low frequency range and “crispy sound” caused by a cyclic sound pattern were determined to be desirable sounds for “American type” motorcycles.