Search Results

This paper presents experimental results for two fuel-related topics in a diesel engine: (1) how fuel volatility affects the premixed burn and heat release rate, and (2) how ignition quality influences the soot formation. Fast evaporation of fuel may lead to more intense heat release if a higher percentage of the fuel is mixed with air to form a combustible mixture. However, if the evaporation of fuel is driven by mixing with high-temperature gases from the ambient, a high-volatility fuel will require less oxygen entrainment and mixing for complete vaporization and, consequently, may not have potential for significant heat release simply because it has vaporized. Fuel cetane number changes also cause uncertainty regarding soot formation because variable ignition delay will change levels of fuel-air mixing prior to combustion.

The liquid and vapor-phase spray penetrations of #2 diesel and neat (100%) soybean-derived biodiesel have been studied at late expansion-cycle conditions in a constant-volume optical chamber. In modern diesel engines, late-cycle staged injections may be used to assist in the operation of exhaust stream aftertreatment devices. These late-cycle injections occur well after top-dead-center (TDC), when post-combustion temperatures are relatively high and densities are low. The behavior of diesel sprays under these conditions has not been well-established in the literature. In the current work, high-speed Mie-scatter and schlieren imaging are employed in an optically accessible chamber to characterize the transient and quasi-steady liquid penetration behavior of diesel sprays under conditions relevant for late-cycle post injections, with very low densities (1.2 - 3 kg/m 3 ) and moderately high temperatures (800 - 1400 K).

The influence of soy- and palm-based biofuels on the in-cylinder sources of unburned hydrocarbons (UHC) and carbon monoxide (CO) was investigated in an optically accessible research engine operating in a partially premixed, low-temperature combustion regime. The biofuels were blended with an emissions certification grade diesel fuel and the soy-based biofuel was also tested neat. Cylinder pressure and emissions of UHC, CO, soot, and NOx were obtained to characterize global fuel effects on combustion and emissions. Planar laser-induced fluorescence was used to capture the spatial distribution of fuel and partial oxidation products within the clearance and bowl volumes of the combustion chamber. In addition, late-cycle (30° and 50° aTDC) semi-quantitative CO distributions were measured above the piston within the clearance volume using a deep-UV LIF technique.

The behavior of the engine-out UHC and CO emissions from a light-duty diesel optical engine operating at two PPCI conditions was investigated for fifteen different fuels, including diesel fuels, biofuel blends, n-heptane-iso-octane mixtures, and n-cetane-HMN mixtures. The two highly dilute (9-10% O₂) early direct injection PPCI conditions included a low speed (1500 RPM) and load (3.0 bar IMEP) case~where the UHC and CO have been found to stem from overly-lean fuel-air mixtures~and a condition with a relatively higher speed (2000 RPM) and load (6.0 bar IMEP)~where globally richer mixtures may lead to different sources of UHC and CO. The main objectives of this work were to explore the general behavior of the UHC and CO emissions from early-injection PPCI combustion and to gain an understanding of how fuel properties and engine load affect the engine-out emissions.

The ignition and flame stabilization characteristics of two synthetic fuels, having significantly different cetane numbers, are investigated in a constant volume combustion vessel over a range of ambient conditions representative of a compression ignition engine operating at variable loads. The synthetic fuel with a cetane number of 63 (S-1) is characterized by ignition delays that are only moderately longer than n-dodecane (cetane number of 87) over a range of ambient conditions. By comparison, the synthetic fuel with a cetane number of 17 (S-2) requires temperatures approximately 300 K higher to achieve the same ignition delays. The much different ignition characteristics and operating temperature range present a scenario where the lift-off stabilization may be substantially different.

Non-conventional operating conditions and fuels in diesel engines can produce longer ignition delays compared to conventional diesel combustion. If those extended delays are longer than the injection duration, the ignition and combustion progress can be significantly influenced by the transient following the end of injection (EOI), and especially by the modification of the mixture field. The objective of this paper is to assess how those long ignition delays, obtained by injecting at low in-cylinder temperatures (e.g., 760-800K), are affected by EOI. Two multi-hole diesel fuel injectors with either six 0.20mm orifices or seven 0.14mm orifices have been used in a 2.34L single-cylinder optical diesel engine. We consider a range of ambient top dead center (TDC) temperatures at the start of injection from 760-1000K as well as a range of injection durations from 0.5ms to 3.1ms. Ignition delays are computed through the analysis of both cylinder pressure and chemiluminescence imaging.

Experiments conducted with a set of reference diesel fuels in an optically accessible, compression-ignition engine have revealed a strong correlation between hydrocarbon (HC) emissions and the flame lift-off length at the end of the premixed burn (EOPMB), with increasing HC emissions associated with longer lift-off lengths. The correlation is largely independent of fuel properties and charge-gas O2 mole fraction, but varies with fuel-injection pressure. A transient, one-dimensional jet model was used to investigate three separate mechanisms that could explain the observed impact of lift-off length on HC emissions. Each mechanism relies on the formation of mixtures that are too lean to support combustion, or “overlean.” First, overlean regions can be formed after the start of fuel injection but before the end of the premixed burn.

Past experimental studies conducted by the current authors on a 13 liter 16.7:1 compression ratio heavy-duty diesel engine have shown that diesel-Compressed Natural Gas (CNG) Reactivity Controlled Compression Ignition (RCCI) combustion targeting low NOx emissions becomes progressively difficult to control as the engine load is increased. This is mainly due to difficulty in controlling reactivity levels at higher loads. For the current study, CFD investigations were conducted in CONVERGE using the SAGE combustion solver with the application of the Rahimi mechanism. Studies were conducted at a load of 5 bar BMEP to validate the simulation results against RCCI experimental data. In the low load study, it was found that the Rahimi mechanism was not able to predict the RCCI combustion behavior for diesel injection timings advanced beyond 30 degCA bTDC. This poor prediction was found at multiple engine speed and load points.

For logistical reasons, the military requires that jet fuel (JP-8, F-34) be used in both jet engines and diesel engines. While JP-8-fueled diesel engines appear to operate successfully in many cases, negative impacts, including engine failures, are occasionally reported. As diesel combustion with JP-8 has not been explored in great detail, fundamental information about JP-8 fuel spray combustion is needed. In this study, we report measurements of liquid-phase penetration length, vapor penetration, and ignition delay made in an optically-accessible combustion vessel over a range of high-temperature, high-pressure operating conditions applicable to a diesel engine. Results show that the liquid-phase penetration of JP-8 is less than that of diesel, owing to the lower boiling point temperatures of JP-8. Despite the more rapid vaporization, the vapor penetration rate of JP-8 matches that of diesel and ignition does not advance.

Low-temperature combustion of diesel fuel was studied in a heavy-duty, single-cylinder, optical engine employing a 15-hole, dual-row, narrow-included-angle nozzle (10 holes × 70° and 5 holes × 35°) with 103-μm-diameter orifices. This nozzle configuration provided the spray targeting necessary to contain the direct-injected diesel fuel within the piston bowl for injection timings as early as 70° before top dead center. Spray-visualization movies, acquired using a high-speed camera, show that impingement of liquid fuel on the piston surface can result when the in-cylinder temperature and density at the time of injection are sufficiently low. Seven single- and two-parameter sweeps around a 4.82-bar gross indicated mean effective pressure load point were performed to map the sensitivity of the combustion and emissions to variations in injection timing, injection pressure, equivalence ratio, simulated exhaust-gas recirculation, intake temperature, intake boost pressure, and load.

The fuel-ambient mixture in vaporized fuel jets produced by liquid sprays is fundamental to the performance and operation of engines. Unfortunately, experimental difficulties limit the direct measurement of local fuel-ambient mixture, inhibiting quantitative assessment of mixing. On the other hand, measurement of global quantities, such as the jet penetration rate, is relatively straightforward. Simplified models to predict local fuel-ambient mixture have also been developed, based on these global parameters. However, experimental data to validate these models over a range of conditions is needed. In the current work, we perform measurements of jet global quantities such as vapor-phase penetration, liquid-phase penetration, spreading angle, and nozzle flow coefficients over a range of conditions in a high-temperature, high-pressure vessel.

The in-cylinder extent of liquid-phase fuel penetration (i.e., the liquid length) is an important parameter in combustion-chamber design because liquid lengths that are too long can lead to wall impingement and corresponding degradation of engine efficiency, emissions, and durability. Previous liquid-length measurements in constant-volume combustion chambers have shown that the liquid length is nominally independent of injection pressure, but these measurements have employed common-rail fuel systems where injection rate is approximately constant during the entire injection event, and they have been conducted under quasi-steady ambient thermodynamic conditions. The objective of the current work is to better understand the effects of injection-rate shape and injection pressure on the liquid length, including possible effects of unsteady ambient conditions in an engine.

We present a parametric analysis of electric vehicle (EV) adoption rates and the corresponding contribution to greenhouse gas (GHG) reduction in the US light-duty vehicle (LDV) fleet through 2050. The analysis is performed with a system dynamics based model of the supply-demand interactions among the fleet, its fuels, and the corresponding primary energy sources. The differentiating feature of the model is the ability to conduct global sensitivity and parametric trade-space analyses. We find that many factors impact the adoption rates of EVs. These include, in particular, policy initiatives that encourage consumers to consider lifetime ownership costs, the price of oil, battery performance, as well as the pace of technological development for all powertrains (conventional internal combustion engines included). Widespread EV adoption can have noticeable impact on petroleum consumption and GHG emissions by the LDV fleet.

This study summarizes the peer-reviewed literature regarding the use of raw pyrolysis liquids (PLs) created from woody biomass as fuels for compression-ignition (CI) engines. First, a brief overview is presented of fast pyrolysis and the potential advantages of PLs as fuels for CI engines. Second, a discussion of the general composition and properties of PLs relative to conventional, petroleum-derived diesel fuels is provided, with emphasis on the differences that are most likely to affect PL performance in CI-engine applications. Next, a synopsis is given of the peer-reviewed literature describing experimental studies of CI engines operated using neat PLs and PLs combined in various ways with other fuels. This literature conclusively indicates that raw PLs and PL blends cannot be used as “drop-in replacements” for diesel fuel in CI engines, which is reflected in part by none of the cited studies reporting successful operation on PL fuels for more than twelve consecutive hours.

Combustion systems with advanced injection strategies have been extensively studied, but there still exists a significant fundamental knowledge gap on fuel spray interactions with the piston surface and chamber walls. This paper is meant to provide detailed data on spray-wall impingement physics and support the spray-wall model development. The experimental work of spray-wall impingement with non-vaporizing spray characterization, was carried out in a high pressure-temperature constant-volume combustion vessel. The simultaneous Mie scattering of liquid spray and schlieren of liquid and vapor spray were carried out. Diesel fuel was injected at a pressure of 1500 bar into ambient gas at a density of 22.8 kg/m3 with isothermal conditions (fuel, ambient, and plate temperatures of 423 K). A Lagrangian-Eulerian modeling approach was employed to characterize the spray-gas and spray-wall interactions in the CONVERGETM framework by means of a Reynolds-Averaged Navier-Stokes (RANS) formulation.

High-efficiency, clean-combustion strategies for heavy-duty diesel engines are critical for meeting stringent emissions regulations and reducing the costs of aftertreatment systems that are currently required to meet these regulations. Results from previous constant-volume combustion-vessel experiments using a single jet of fuel under quiescent conditions have shown that mixing-controlled soot-free combustion (i.e., combustion where soot is not produced) is possible with #2 diesel fuel. These experiments employed small injector-orifice diameters (≺ 150 μm) and high fuel-injection pressures (≻ 200 MPa) at top-dead-center (TDC) temperatures and densities that could be achievable in modern heavy-duty diesel engines.

Interest in natural gas as a fuel for light-duty transportation has increased due to its domestic availability and lower cost relative to gasoline. Natural gas, comprised mainly of methane, has a higher knock resistance than gasoline making it advantageous for high load operation. However, the lower flame speeds of natural gas can cause ignitability issues at part-load operation leading to an increase in the initial flame development process. While port-fuel injection of natural gas can lead to a loss in power density due to the displacement of intake air, injecting natural gas directly into the cylinder can reduce such losses. A study was designed and performed to evaluate the potential of natural gas for use as a light-duty fuel. Steady-state baseline tests were performed on a single-cylinder research engine equipped for port-fuel injection of gasoline and natural gas, as well as centrally mounted direct injection of natural gas.

The Leaner Lifted-Flame Combustion (LLFC) strategy offers a possible alternative to low temperature combustion or other globally lean, premixed operation strategies to reduce soot directly in the flame, while maintaining mixing-controlled combustion. Adjustments to fuel properties, especially fuel oxygenation, have been reported to have potentially beneficial effects for LLFC applications. Six fuels were selected or blended based on cetane number, oxygen content, molecular structure, and the presence of an aromatic hydrocarbon. The experiments compared different fuel blends made of n-hexadecane, n-dodecane, methyl decanoate, tri-propylene glycol monomethyl ether (TPGME), as well as m-xylene. Several optical diagnostics have been used simultaneously to monitor the ignition, combustion and soot formation/oxidation processes from spray flames in a constant-volume combustion vessel.

Computational fluid dynamic (CFD) simulations that include realistic combustion/emissions chemistry hold the promise of significantly shortening the development time for advanced high-efficiency, low-emission engines. However, significant challenges must be overcome to realize this potential. This paper discusses these challenges in the context of diesel combustion and outlines a technical program based on the use of surrogate fuels that sufficiently emulate the chemical complexity inherent in conventional diesel fuel.

Sandia National Laboratories has been investigating a new, integrated approach to generating electricity with ultra low emissions and very high efficiency for low power (30 kW) applications such as hybrid vehicles and portable generators. Our approach utilizes a free piston in a double-ended cylinder. Combustion occurs alternately at each cylinder end, with intake/exhaust processes accomplished through a two stroke cycle. A linear alternator is mounted in the center section of the cylinder, serving to both generate useful electrical power and to control the compression ratio by varying the rate of electrical generation. Thus, a mechanically simple geometry results in an electronically controlled variable compression ratio configuration. The capability of the homogeneous charge compression ignition combustion process employed in this engine with regards to reduced emissions and improved thermal efficiency has been investigated using a rapid compression expansion machine.