Search Results

The authors have developed a measurement technique using a new digital telemeter which measures the piston secondary motion as ensuring high accuracy while under the operation. We applied this new digital telemeter to several measurements and analysis on the piston secondary motion that can cause piston noises, and here are some of the results from our measurement. We have confirmed that these piston motions vary by only several tenths of millimeter changes of the piston specifications such as the piston-pin offset and the center of gravity of the piston. As in other cases, we have found that a mere change of pressure in the crankcase or the amount of lubricating oil supplied on the cylinder bore varies the piston motion that may give effect on the piston noises.

This paper analyzes low-speed pre-ignition (LSPI), a sudden pre-ignition phenomenon that occurs in downsized boosted gasoline engines in low engine speed high-load operation regions. This research visualized the in-cylinder state before the start of LSPI combustion and observed the behavior of particles, which are thought to be the ignition source. The research also analyzed pre-ignition by injecting deposit flakes and other combustible particulate substances into the combustion chamber. The analysis found that these particles require at least two combustion cycles to reach a glowing state that forms an ignition source. As a result, deposits peeling from combustion chamber walls were identified as a new mechanism causing pre-ignition. Additionally, results also suggested that the well-known phenomenon in which the LSPI frequency rises in accordance with greater oil dilution may also be explained by an increase in deposit generation.

We developed a technique to measure oil film pressure distribution in engine main bearings using thin-film pressure sensors. The sensor is 7μm in thickness, and is processed on the surface of an aluminum alloy bearing. In order to increase the durability of the sensor, a layer of MoS2 and polyamide-imide was coated on thin-film sensors. This technique was applied to a 1.4L common-rail diesel engine operated at a maximum speed of 4,500r/min with a 100Nm full load, and the oil film pressure was monitored while the engine was operating. The measured pressure was compared with calculations based on hydrodynamic lubrication (HL) theory.

A new clean diesel combustion concept has been proposed and its excellent performance with respect to gas emissions and fuel economy were demonstrated using a single cylinder diesel engine. It features the following three items: (1) low-penetrating and highly dispersed spray using a specially designed injector with very small and numerous orifices, (2) a lower compression ratio, and (3) drastically restricted in-cylinder flow by means of very low swirl ports and a lip-less shallow dish type piston cavity. Item (1) creates a more homogeneous air-fuel mixture with early fuel injection timings, while preventing wall wetting, i.e., impingement of the spray onto the wall. In other words, this spray is suitable for premixed charge compression ignition (PCCI) operation, and can decrease both nitrogen oxides (NOx) and soot considerably when the utilization range of PCCI is maximized.

In diesel engines with a straight intake port and a lipless cavity to restrict in-cylinder flow, an injector with numerous small-diameter orifices with a narrow angle can be used to create a highly homogeneous air-fuel mixture that, during PCCI combustion, dramatically reduces the NOX and soot without the addition of expensive new devices. To further improve this new combustion concept, this research focused on cooling losses, which are generally thought to account for 16 to 35% of the total energy of the fuel, and approaches to reducing fuel consumption were explored. First, to clarify the proportions of convective heat transfer and radiation in the cooling losses, a Rapid Compression Machine (RCM) was used to measure the local heat flux and radiation to the combustion chamber wall. The results showed that though larger amounts of injected fuel increased the proportion of heat losses from radiation, the primary factor in cooling losses is convective heat transfer.

To meet the requirements for lower fuel consumption and emissions as well as higher performances, a “Variable Valve Timing - intelligent by Electric motor (VVT-iE)” system has been newly developed. The system has been firstly adopted to the intake valve train of the Toyota's new 4.6 and 5.0 litter V8 SI engine series. The VVT-iE is composed of a cam phasing mechanism connected to the intake camshaft and brushless motor integrated with its intelligent driver. The motor-actuated system is completely free from operating limitation caused from hydraulic conditions. This enjoys an advantage for reducing cold HC. The system also presents further reduction in fuel consumption.

It has been reported that the middle range of gasoline distillation temperatures strongly affects vehicle driveability and exhaust hydrocarbon (HC) emissions, and that MTBE(CH3-O-C4H9)- blended gasoline causes poor driveability during warm-up. The present paper is concerned with the results of subsequent detailed research on gasoline characteristics, exhaust emissions and driveability. In this paper, first it is demonstrated by using four models of passenger cars having different types of exhaust gas treatment system that decreased 50% distillation temperature (T50) reduces exhaust HC emission. This result indicates lowering T50 in the market will contribute to improving air quality. Secondly gasoline behavior in the intake manifold is investigated by using an engine on the dynamometer in order to clarify the mechanisms of HC emission increase and poor engine response which are caused by high T50.

The hole diameter of injection nozzles in diesel engines has become smaller and the nozzle coking could potentially cause injection characteristics and emissions to deteriorate. In this research, engine tests with zinc-added fuels, deposit analyses, laboratory tests and numerical calculations were carried out to clarify the deposit formation mechanisms. In the initial phase of deposit formation, lower zinc carboxylate formed close to the nozzle hole outlet by reactions between zinc in the fuel and lower carboxylic acid in the combustion gas. In the subsequent growth phase, the main component changed to zinc carbonate close to nozzle hole inlet by reactions with CO₂ in the combustion gas. Metal components and combustion gases are essential elements in the composition of these deposits. One way of removing these deposits is to utilize cavitations inside the nozzle holes.

Direct injection gasoline engines require extremely advanced control of air-fuel mixture in order to achieve good stratified combustion. The method of examining quality of mixture formation in combustion chambers is essential for the achievement. In this research, air-fuel mixture in combustion chamber of the TOYOTA D-4 engine was analyzed in space and time by visualization as well as Air/Fuel ratio measurement by multi-point and high response techniques. Thus the effects that injection timing, swirl and fuel pressure exerted to mixture formation were elucidated.

In order to clarify the combustion behavior in the ultra high engine speed range, a new technique has been developed. This technique is composed of ionization current detection and flame observation, and is highly heat-resistant, vibration-resistant, and has a quick response. From analyzing the flame front propagation in the high-speed research engine, it was found that the flame propagated throughout the entire cylinder over almost the same crank angle period irrespective of engine speed introduction.

In order to clarify the diesel fuel spray characteristics inside the cylinder, we developed two novel techniques, which are preparation of same level of temperature and pressure ambient as inside cylinder and quantitative measurement of vapor concentration. The first one utilizes combustion-type constant-volume chamber (inner volume 110cc), which allows 5 MPa and 873K by igniting the pre-mixture (n-pentane and air) with two spark plugs. In the second technique, TMPD vapor concentration is measured by using Laser Induced Exciplex Fluorescence method (LIEF). The concentration is compensated by investigation of the influence of ambient pressure (from 3 to 5 MPa) and temperature (from 550 to 900 K) on TMPD fluorescence intensity. By using two techniques, we investigated the influence of nozzle hole diameter, injection pressure and ambient condition on spray characteristics.

An ignition simulation and an ignition visualization method that analyze effects of spark plug electrode design have been developed. In the ignition simulation, a programmed heat source corresponds to the discharge energy in the spark gap, and the flame-kernel generation and flame propagation are calculated on the heat balance in the gap, in consideration of thermal transmission to the electrodes. The results by this simulation indicate that high ignitability of fine ground electrode spark plugs is because the miniaturization of the ground electrode reduces the heat loss, and flame growth is thus less disturbed by the loss. The ignition visualization includes taking Schlieren images by laser light to capture flame kernels with weaker luminescence intensity compared to ignition discharge spark luminescence. This visualization enables the observation of the influence of the shape of spark plug electrodes on flame growth.

The authors have developed a measurement technique equipped with new digital telemeter for strain, motion and temperature of engine parts under high speed running operation with high accuracy. This telemeter has an original signal processing method in which the sensor outputs are directly converted to digital signals without conventional amplifiers and A/D converters. This telemeter enables multipoint measurements at high engine speed in small gasoline engines because of its compactness and lightweight. And this enables long hours of engine test without concern over battery life because of its low power consumption and self-contained power generation. We applied new developed digital telemeter to several measurements and analysis on the piston, piston ring and connecting rod.

In recent years, CO2 emission constraint has been strengthened worldwide in order to fight global warming, and it is believed that the demand for compact and energy-saving car will be increasing year after year. On the other hand, larger interior space of vehicle to as-sure passenger comfort is demanded, so that the car air-conditioner is required to be smaller and energy saving efficient further more. Therefore, we have developed the new type of compact high-efficiency blower fan for compact car air-conditioning system (HVAC). Because of the requirements that the blower fan to be not only small size but energy-saving and low noise efficient, we started this development by modifications for basic blower fan internal air flow system of existing products. Generally, Sirocco fan, which is compact and able to supply high pressure, is often adopted for blower to be used for car air-conditioner.

In gasoline direct injection engines it is important to optimize fuel spray characteristics, which strongly affect stratified combustion process. Spray simulation is anticipated as a tool for optimizing nozzle design, but conventional simulation, which is based on experimental data and/or empirical laws regarding spray boundary condition at the nozzle exit, cannot predict the effect of various nozzle geometries on spray characteristics. In Japan, a fan spray injected from a slit type nozzle has recently been adopted for gasoline direct injection engines. This paper proposes a computational model for the fan spray. The structure of two-phase flow inside the nozzle is numerically analyzed using the volume of fluid (VOF) method in a three-dimensional CFD code based on the nozzle geometry. The results of these analyses are applied to classical linear instability theory to calculate fuel droplet mean diameter after primary breakup.

This paper describes the analyses to improve both stratified and homogeneous charge combustion of a gasoline direct injection engine. In this study, computational fluid dynamics (CFD) and high-speed hydrocarbon (HC) measurement were employed to observe the mixture formation process. The analysis of the combustion flame propagation was conducted by in-cylinder visualization and ion current measurement. As a result of the analyses, the following conclusions were made: 1 An oval shaped wall cavity can direct the mixture gas to the vicinity of the spark plug better than a conventional shell-shaped wall cavity. The oval shaped wall cavity can improve fuel consumption and HC emission at stratified charge combustion. 2 A shallow cavity improves the homogenization of mixture gases and wide open throttle (WOT) performance.

In order to evaluate the toughness of automotive ECU's to electrostatic discharge, a conventional method where electrostatic discharge pulse is applied to connector parts on a printed circuit board is commonly used. But quantitative re-designing principles to improve the static electricity tolerance have not been made clear that completely utilizes the test data shown below till now, because propagation mechanism of static electricity on a circuit board is not clear. This paper describes the ESD current measurement technique which detects the near magnetic field generated by ESD currents. We developed to measure the ESD currents using the new loop antenna on a circuit board. The ESD current, was generated with the static electricity applied to a model circuit pattern in conformity with IEC and ISO standard and measured using the antenna. Also it was able to visualize how static electricity energy would propagate through the circuit board.

To develop injection nozzles and to improve the numerical simulation technology of fuel spray, a measuring technology to analyze the process of disintegration into droplets accurately is required. Performances required by a spray droplets measuring device are: “ability to measure in the combustion condition inside the engine cylinder”, “ability to measure the diameter of spray droplets in high-density fields”, “ability to measure the structure of spray droplets in 3D”, and an improved measuring accuracy of non-spherical droplets. These elements are required in order to analyze the spray droplets structure of gasoline direct injection engines. As a promising method to satisfy these requirements, the laser holography method has been already suggested. However, it has some drawbacks, such as a difficulty in measuring spray droplets in high-density fields and over a long analysis period.

In vehicle control systems such as ABS (anti-lock braking system) or active suspension control, sensors for detecting longitudinal and/or lateral acceleration of vehicles (acceleration of up to ± 9.8 m/s2, with frequency range of DC to 20 Hz) is necessary. The principle of acceleration detection for this sensor is as follows. A permanent magnet levitates steadily in magnetic fluid by the action of the magnetic field generated by the magnet itself. The magnet moves by the application of acceleration on the mass of the magnet. This change of position of the magnet is detected by the Hall element, and thus acceleration is measured as an electrical signal. This sensor consists of only magnetic fluid, a permanent magnet, housing, a pair of Hall elements and an electronic circuit.

Recently CO₂ emission regulation has become more stringent and higher thermal efficiency of the internal combustion engine is required. Spray-guided gasoline direct injection engine has promising potential for lower fuel consumption. The purpose of this study is to clarify the air-fuel mixture formation requirements and to investigate the spray specification of multi-hole nozzle injector for spray-guided stratified combustion.