Search Results

Building on two decades of expertise, a fourth generation fleet test protocol is presented for assessing the response of engine performance to gasoline additive treatment. In this case, the ability of additives to remove pre-existing deposit from the intake systems of port fuel injected vehicles has been examined. The protocol is capable of identifying real benefits under realistic market conditions, isolating fuel performance from other effects thereby allowing a direct comparison between different fuels. It is cost efficient and robust to unplanned incidents. The new protocol has been applied to the development of a candidate fuel additive package for the North American market. A vehicle fleet of 5 quadruplets (5 sets of 4 matched vehicles, each set of a different model) was tested twice, assessing the intake valve clean-up performance of 3 test fuels relative to a control fuel.

In this work, a dynamically loaded hydrodynamic journal bearing test rig is developed and introduced. The rig is a novel design, using a hydraulic actuator with fast acting spool valves to apply load to a connecting rod. This force is transmitted through the connecting rod to the large end bearing which is mounted on a spinning shaft. The hydraulic actuator allows for fully variable control and can be used to apply either static load in compression or tension, or dynamic loading to simulate engine operation. A variable speed electric motor controls shaft speed and is synchronized to the hydraulic actuator to accurately simulate loading to represent all four engine strokes. A high precision torque meter enables direct measurements of friction torque, while shaft position is measured via a high precision encoder.

The Scuderi internal combustion engine is characterized by a split cycle that divides the four strokes of a conventional combustion cycle over two paired cylinders, one intake/compression cylinder and one power/exhaust cylinder, connected by a crossover port. This split cycle also has an additional high pressure “crossover” gas transfer phase versus the conventional 4-stroke cycle, during which the charge air is moved from the first to the second cylinder. The intake/compression, power/exhaust and crossover events are repeated every revolution, i.e. over two cycles, with a small phase angle between the two cylinders. The separate cylinders enable opportunities for improved combustion and the possibility for pneumatic hybridization of the engine. This paper describes the technical challenges posed by the actuation of the crossover valves in the Scuderi Split Cycle research engine.

The performance of modern spark ignition engines with electronically controlled fuel injection systems may be adversely affected by formation of deposits around the intake valve. The rate of deposit formation is sensitive to fuel composition and boiling point distribution, as well as engine design and operating conditions. Deposit control additives are available, and full-scale engine and vehicle tests have been developed to rate fuel deposition characteristics. However, the expense associated with full-scale testing, combined with the many variables affecting repeatability, create a need for a well controlled laboratory-scale bench test. This paper describes the development of both the test apparatus and methodology to accurately reproduce the conditions present at the intake valve of an operating engine. Procedures were developed to simulate both a “keep clean” sequence, with neat or additized fuel, and also a “clean-up” sequence, using fuel that contains a deposit control additive.

An electromagnetic valve actuation (EVA) system was developed and applied to a Kohler Command Series engine. Engine development and testing was conducted for the purpose of evaluating the performance of the EVA-equipped engine, running on natural gas, in an engine-test laboratory environment. As part of this effort, a personal computer-based engine control system, which managed the fueling, ignition, throttling, and intake/exhaust valve control functions, was developed. The evaluation included an investigation into increasing engine power output and full load efficiency, as well as increased part load efficiency. Techniques including optimized valve events as a function of operating condition, and throttleless operation using early and late intake valve closing are presented. Engine simulation results are compared with actual engine data and presented in this paper.

Fossil fuel consumption is a significant factor in terms of both economic and environ-mental impact of on- and off-highway systems. Because fuel consumption can be directly tied to equipment efficiency, gains in efficiency can lead to reduction in operating costs as well as conservation of nonrenewable resources. Fluid performance has a direct effect on the efficiency of a hydraulic system. A procedure has been developed for measuring a fluid's effect on the degree to which mechanical power is efficiently converted to hydraulic power in pumps typical of off-highway applications.

The Texas Department of Transportation (TxDOT) began using an emulsified diesel fuel in July 2002. They initiated a simultaneous study of the effectiveness of this fuel in comparison to 2D on-road diesel fuel, which they use in both their on-road and off-road equipment. The study also incorporated analyses for the fleet operated by the Associated General Contractors (AGC) in the Houston area. Some members of AGC use 2D off-road diesel fuel in their equipment. The study included comparisons of fuel economy and emissions for the emulsified fuel relative to the conventional diesel fuels. Cycles that are known to be representative of the typical operations for TxDOT and AGC equipment were required for use in this study. Four test cycles were developed from data logged on equipment during normal service: 1) the TxDOT Telescoping Boom Excavator Cycle, 2) the AGC Wheeled Loader Cycle, 3) the TxDOT Single-Axle Dump Truck Cycle, and 4) the TxDOT Tandem-Axle Dump Truck Cycle.

The design and testing of the valve train for a new two-stroke diesel engine concept [1,2] is presented. The gas exchange of this process requires extremely fast-acting inlet valves, which constituted a very demanding designing task. A simulation model of the prototype valve train was constructed with commercially available software. The simulation program served as the main tool for optimizing the dynamic behavior of the valve train. The prototype valve train was built according to the simulations and valve acceleration measurements were performed in order to validate the simulation results. The simulations and measurements are presented in detail in this paper.

A novel two-stroke engine concept is introduced. The cylinder scavenging takes place during the upward motion of the piston. The gas exchange valves are similar to typical four-stroke valves, but the intake valves are smaller and lighter. The scavenging air pressure is remarkably higher than in present-day engines. The high scavenging air pressure is produced by an external compressor. The two-stroke operation is achieved without the drawbacks of port scavenged engines. Moreover, the combustion circumstances, charge pressure and temperature and internal exhaust gas re-circulation (EGR) can be controlled by using valve timings. There is good potential for a substantial reduction in NOx emissions through the use of adjustable compression pressure and temperature and by using the adjustable amount of exhaust gas re-circulation.

Computational Fluid Dynamics (CFD) analysis software is being developed by many companies and it is a valuable tool in designing hydraulic components. CFD analysis can provide accurate predictions of pressure drop in fluid flow paths and offer insight into the primary source of losses. When used in conjunction with solid modeling design software, the process of optimizing a design can be accomplished much quicker, reducing development costs and time. This paper presents a CFD analysis of an existing valve design and compares it to an improved design. The source of the primary losses of the existing valve will be identified which will lead to modifications to design features that minimize those losses. These modifications will be modeled and analyzed for predicted improvements. Pressure drop tests will be conducted on the original design to verify the analysis. Internal pressure loading of valve parts cannot easily be determined by testing.

The measurement of piston temperature in a reciprocating engine has historically been a very time-consuming and expensive process. Several conditions exist in an engine that measurement equipment must be protected against. Acceleration forces near 2000 G's occur at TDC in automotive engines at rated speed. Operating temperatures inside the crankcase can range to near 150°C. To allow complete mapping of piston temperature, several measuring locations are required in the piston and data must be obtained at various engine operating conditions. Southwest Research Institute (SwRI) has developed a telemetry-based system that withstands the harsh environments mentioned above. The device is attached to the underside of a piston and temperature data is transmitted to a receiving antenna in the engine crankcase. The key element of this device is a tiny power generator which utilizes the reciprocating motion of the piston to generate electricity thus allowing the transmitter to be self-powered.

The engine intake process governs many aspects of the flow within the cylinder. The inlet valve is the minimum area, so gas velocities at the valve are the highest velocities seen. Geometric configuration of the inlet ports and valves, and the opening schedule create organized large scale motions in the cylinder known as swirl and tumble. Good charge motion within the cylinder will produce high turbulence levels at the end of the compression stroke. As the turbulence resulting from the conversion energy of the inlet jet decays fast, the strategy is to encapsulate some of the inlet jet in the organized motions. In this work the baseline port of a 2.0 L gasoline engine was modified by inserting a tumble plate. The work was done in support of an experimental study for which a new single-cylinder research engine was set up to allow combustion system parameters to be varied in steps over an extensive range. Tumble flow was one such parameter.

Dedicated EGR has shown promise for achieving high efficiency with low emissions [1]. For the present study, a 4-cylinder turbocharged GDI engine which was modified to a D-EGR configuration was used to investigate the impact of valve phasing and different injection strategies on the reformate production in the dedicated cylinder. Various levels of positive valve overlap were used in conjunction with different approaches for dedicated cylinder over fueling using PFI and DI fuel systems. Three speed-load combinations were studied, 2000 rpm 4 bar IMEPg, 2000 rpm 12 bar IMEPg, and 4000 rpm 12 bar IMEPg. The primary investigation was conducted to map out the dedicated cylinders' performance at the operating limits of intake and exhaust cam phasing. In this case, the limits were defined as conditions that yielded either no reformate benefit or led to instability in the dedicated cylinder.

The Scuderi engine is a split cycle design that divides the four strokes of a conventional combustion cycle over two paired cylinders, one intake/compression cylinder and one power/exhaust cylinder, connected by a crossover port. This configuration provides potential benefits to the combustion process, as well as presenting some challenges. A Miller cycle configuration of the engine is made possible by turbocharging with a downsized compressor cylinder and has been modeled in 1-dimensional cycle simulation software.

The SwRI/BMW N.A. Intake Valve Deposit Test procedure was the first performance-based test procedure adopted for fuels qualification in the United States. The initial fuel evaluations were begun in January 1988 with six 1985 BMW 318i vehicles. Since that time, the fleet has grown to include over 60 BMW cars, and more than 2000 tests have been performed. This paper gives a statistical summary of approximately 1800 tests performed over a four-year period. Performance data and possible sources of test variation are discussed. Data and analyses offered represent results of tests by all clients. However, data is presented such that no individual test or client is identified.

The United States and Europe are mandating increasingly severe diesel fuel specifications, particularly with respect to sulfur content, and in some areas, aromatics content. This trend is directed towards reducing vehicle exhaust emissions and is generally beneficial to fuel quality, ignition ratings, and stability. However, laboratory studies, as well as recent field experience in Sweden and the United States, indicate a possible reduction in the ability of fuels to lubricate sliding components within the fuel injection system. These factors, combined with the trend toward increasing injection pressure in modern engine design, are likely to result in reduced durability and failure of the equipment to meet long-term emissions compliance. The U.S. Army Belvoir Fuels and Lubricants Research Facility (BFLRF) located at Southwest Research Institute (SwRI) developed an accelerated wear test that predicts the effects of fuel lubricity on injection system durability.

System contamination caused by contaminates or small particles built-in, self-generated, or inhaled from environment presents severe problems. The problems include but are not limited to the malfunctioning of valves, pumps, seals and injectors or lock-up of these components; increased wear of bearings, piston rings, and other friction components; and degradated machine performance. In general, system contamination changes a deterministic system into a stochastic system and shortens machinery service life. In this paper, these contamination problems are discussed in categories and associated analysis, testing and computer modeling methodologies are also discussed.

This paper describes the concept, analysis and preliminary rig proving of a 2-mode mechanical variable-valve-actuation system, “Latchcam”, designed initially for prototype bucket-tappet overhead-cam applications. The rig-test data allows the prototype Latchcam performance to be compared to a state-of-art 2-mode system in a current cylinder-head application. Some general design implications and issues are reviewed.

The principles of the magnetic-perturbation method of flaw detection and the Barkhausen noise residual stress measurement method are briefly reviewed. It is suggested that they provide very powerful tools for assuring improved ball bearing performance. The methods are applied for the evaluation of ball bearing races. Typical experimental results are presented along with metallurgical sectioning correlation.

Fuel conservationists will welcome this practicable proposal for converting railroads from diesel fuel to propane gas propulsion. Propane is no newcomer to the fuel family, but the advantages of economy, simplicity of operation, minimal maintenance, and extended life of equipment, as presented in this paper, show up its unexploited and extensive potential use in all mobile units. This careful study includes experimental results and data especially applied to railroad engines, even to conversion plans for existing engines that allows an interchangeable fuel system to accommodate present supply and variable cost factors in the United States.