Search Results

With the current state of ever rising fuel prices and unavailability of affordable alternate technologies, significant research and development efforts have been invested in recent times towards improving fuel efficiency of vehicles powered with conventional internal combustion engines. To achieve this, a varied approach has been adopted by researchers to cover the entire energy chain including fuel quality, combustion quality, power generation efficiency, down-sizing, power consumption efficiency, etc. Apart from energy generation, distribution and consumption, another domain that has been subjected to significant scrutiny is energy recuperation or recovery. A moving vehicle and a running engine provide a number of opportunities for useful back-recovery and storage of energy. The most significant sources for recuperation are the kinetic energy of the moving vehicle or running engine and to a lesser extent the thermal energy from medium such as exhaust gas.

With India achieving the BSVI milestone, the diesel particulate filter (DPF) has become an imperative component of a modern diesel engine. A DPF system is a device designed to trap soot from exhaust gas of the diesel engine and demands periodic regeneration events to oxidize the accumulated soot particles. The regeneration event is triggered either based on the soot mass limit of the filter or the delta pressure across it. For a Heavy Duty Diesel Engine (HDDE), pressure difference across the DPF is not usually reliable as the size of the DPF is large enough compared to the DPF used ina passenger vehicle diesel engine. Also, the pressure difference across DPF is a function of exhaust mass flow and thus it makes it difficult to make an accurate call for active regeneration. This demands for a very accurate soot estimation model and it plays a vital role in a successful regeneration event.

As the vehicle functions are getting distributed over multiple ECUs in order to realize various complex control functions, the need for sophisticated on-board diagnostic strategies are increasing in automotive domain, leading to a significant amount of hardware and software implementations for fault management inside various ECUs in the vehicle. This paper proposes optimized vehicle level approach for fault management strategies, wherein a centralized intelligent Gateway Module is proposed in the vehicle network architecture, which will be responsible for fault management of the complete vehicle in a chronological sequence. This Gateway Module will thereby have the possibility to group a cluster of faults raised by different ECUs and correlate them meaningfully to guide the operator towards root cause of the fault.

Reduction of NOx (Oxides of Nitrogen) and particulates from engine exhaust is one of the prime considerations in current research and development in automotive industry. The present paper describes the combustion optimization done on a four cylinder, 4 liter DI diesel engine to meet stringent Euro-III emission norms. The engine FIE (Fuel Injection Equipment) and injector geometry was optimized for performance and emission. Smoke measurements were considered as indicative of soot, to predict particulate emissions. This was done to simplify the overall process and save development time. It was concluded that by combining the flexibility of electronically controlled fuel injection begin, with improved nozzle technologies, with higher spray velocities and spray penetration, a considerable reduction in NOx and particulate emissions can be achieved. This can serve as a low cost solution, without any exhaust after-treatment systems.

It is customary to select a twist beam rear suspension for front wheel driven small and medium range passenger cars. Besides better primary / secondary ride comfort, roll stiffness tuning ability, ease of assembly & good packaging solutions than the conventional semi trailing arm/ rigid axle suspensions, twist beam suspension system accentuate the concentration required in placing & orienting the cross beam to achieve certain imperative kinematical characteristics. In order to make the solutions of the required kinematical targets viable, it is vital to have the packaging space and stress concentration within yield limits given the weight & cost targets. This paper presents the work done on twist beam type suspension for a new generation entry level B-Class hatchback vehicle developed. To reduce the time consumed in validation of different design proposals a virtual validation process was developed.

Design of a Cabin Tilting System of heavy trucks, a multi degree of freedom mechanism, is a challenge. Factors like adequate tilting angle, cabin styling, packaging, non interference of tilting system with ride comfort, forces in the system, specifications of the hydraulic system, are all very important for designing the system. Numerous considerations make the design process highly iterative hence longer design time. This paper primarily focuses on Kinematics and Dynamic analysis of the system in ADAMS and validation of system with real time testing results. Intention of this work is to make a parametric ADAMS model and link it to a Knowledge Based Engineering application to facilitate designer to quickly carry out design iterations for reducing development time. The Knowledge Based Engineering software is made using object oriented language called ‘Object Definition Language’ which has been developed using C and C++ software languages.

Modern vehicles complexity is increasing to meet the demands of user. Automatic wiper and headlamp activation system using rain light sensor, (RLS) is one of the popular customer requirement. RLS is a combination of an infrared rain sensor and an optical light sensor. The RLS and controller operate the front wiper once it detects rain droplets on the windscreen. It switches on the headlamps automatically when while vehicles enter in to the tunnel. During integration of a rain light sensor on a vehicle the following should be considered: customer usage pattern, environmental factors, light intensity, raining pattern and vehicle architecture limitations. This paper illustrates the methodology used calibrated a pre-developed rain light sensor for specific markets like India.

EU directive 2005/64/EC on type approval of motor vehicles with respect to their Reusability, Recyclability and Recoverability ( RRR ) requires vehicle manufacturers to put in place the necessary arrangements and procedures for Parts, Materials and Weight (PMW ) data collection from full chain of supply. This is required to perform the calculations of recyclability rate and recoverability rate in line with ISO 22628. Commonly practiced data collection methodologies included spreadsheet and use of internationally available IT support system for collection of material data. Data complexity and prohibitive cost for using Internationally available IT Support systems like IMDS (International Material Data System) has led to the in-house development of IT enabled Solution customizing Siemens PLM software product (Team centre Enterprise) and SAP (SRM suite).

On Board Diagnostics norms enforced by regulatory authorities of many countries require logging of distance traveled by the vehicle with MIL (malfunction indicator lamp) illuminated. This log needs to be maintained in non-volatile ECU memory. Conventional techniques maintain the log in a volatile memory during vehicle run-time and transfer the same to non-volatile memory when ignition is turned off. This requires use of a “power-hold” relay to keep an ECU power alive while the logged data in volatile memory is being transferred to non-volatile memory when ignition is switched-off. A novel strategy described in this paper avoids interface with power-hold relay, thereby reducing the system complexity. The design philosophy described makes use of an EEPROM to maintain the distance log. An innovative algorithm is employed to ensure that endurance specifications are not violated during the vehicle life-time.

Automotive embedded control systems need to implement real-time closed-loop control strategies for controlling valves, motors, etc. The implementation needs to focus on use of low cost hardware and efficient software with minimal foot-print so as to adequately meet the application requirement. This paper highlights the low cost hardware and software design concepts by way of a case study related to control of progressive EGR valve. The control strategy is based on "map-driven set-points" where percentage opening of the valve is stored in the form of 16x16 matrices. The set-points are accessed based on instantaneous throttle and engine rpm values which form the row and column indices of the map. The closed loop control algorithm eliminates the need for multiplication by implementing "feed-forward with integral control algorithm." A feed-forward map specifies the most likely PWM duty cycle to be applied to the valve for a given set-point.

The AMT (Automated Manual Transmission) has attracted increasing interest of automotive researches, because it has some advantages of both MT (Manual Transmission) and AT (Automatic Transmission), such as low cost, high efficiency, easy to use and good comfort. The hill-start assistance is an important feature of AMT. The vehicle will move backward, start with jerk, or cause engine stalling if failed on the slope road. For manual transmission, hill-start depends on the driver's skills to coordinate with the brake, clutch and throttle pedal to achieve a smooth start. However, with the AMT, clutch pedal is removed and therefore, driver can’t perceive the clutch position, making it difficult to hill-start with AMT without hill-start control strategy. This paper discussed about the hill start control strategy and its functioning.

This literature is in the field of communication networks where different Electronic Control Units (ECUs) communicate with each other over Controller Area Network (CAN) protocol. Typically these types of CAN networks are widely used in automotive vehicles, plant automations, etc. This proposed method is applicable in all such applications where controller area network is used as backbone electrical architecture. This literature proposes a new method of CAN signal packing into CAN frames so that network bus-load is minimized so that more number of CAN signals can be packed and more number of ECUs can be accommodated within a CAN network. The proposed method also ensures that the age of each CAN signal is minimized and all CAN signals reach the intended receiving ECUs within their maximum allowed age. Typically network designers are forced to design and develop multiple sub-networks and network gateways to get rid of network bus-load.

Small goods carrier and passenger vehicles powered by Naturally Aspirated (NA) Direct Injection (DI) diesel engines are popular in Indian automobile market. However, they suffer from inherently high radiated noise and poorly perceived sound quality. This paper documents the steps taken to reduce the radiated noise level from such an engine through structural modifications of major noise radiating components identified in the sound power analysis. The work is summarized as follows; Baseline radiated noise measurements of power train and identification of major noise sources through sound intensity mapping and noise source ranking (NSR) in an Engine Noise Test Cell (ENTC) Design modifications for identified major sources in engine structure Vehicle level assessment of the radiated noise in a Vehicle Semi-Anechoic Chamber (VSAC) for all the design modifications. A reduction of 7 dB at hot idle and 4 - 8 dB in loaded speed sweep conditions was observed with the recommended modifications.

Diesel engines tend to operate on lower exhaust temperatures, compared to their gasoline counterparts. Exhaust emission control becomes a significant issue at these lower temperatures, as any catalytic converter needs certain light off temperature to commence functioning. The trend so far has been to move the catalytic converters closer to the exhaust manifold, in order to get the benefit of higher temperatures - but most of the applications are limited to the location available after the turbo chargers. This is due the fact that very minute and efficient catalyst is required, if it has to be placed before the turbo charger. This catalyst also needs to be extremely durable to take care of high exotherms which occur within the catalysts and also to prevent any possible damage to the turbo chargers.

The power output of an internal combustion engine is directly proportional to the amount of air that can be forced into the cylinder per cycle and the amount of fuel that can be burned efficiently. The amount of air is most effectively increased by means of a mechanical supercharger. The purpose of this paper is attempting the non mechanical supercharging ways (Supercharging by means of gas dynamic effects) for naturally aspirated (NA) diesel engines and understanding in a better way the induction gas dynamics and its influence on engine performance characteristics. Wave dynamics in the intake system has strong influence on the performance of naturally aspirated internal combustion (IC) engines. This paper presents an application of Helmholtz resonator in the induction system of the naturally aspirated diesel engine to improve the engine breathing efficiency (volumetric efficiency).

Increasing number of ECU's (Electronic Control Units) being used in modern vehicles have given rise to HIL (hardware in the loop) testing, and model based design approach to design/test ECU's even before the proto-type vehicle is ready. However, it is not uncommon to discover surprising system design lapses during actual vehicle operation reported after vehicle launch. Major cause behind such lapses are found to be the gap between actual field performance/robustness of various vehicle sub-systems interfaced with ECU's and those modeled as ideal cases during HIL testing in the lab. This creates a need to evolve effective vehicle-level validation strategies to expose such performance deficiencies of real life sub-systems provided by the vendors. This paper describes a new approach to validate ECU in real time.

The modern trend of engine downsizing for CO₂ reduction coupled with stringent emission norms compel the engine air inlet system to outperform the conventional designs. Modern turbo diesel engine air inlet system handles higher & higher air flow, boost pressure and temperature. Air inlet system ducting designs have become complex due to oil particles (received through PCV system), engine movement and isolation for NVH. Air inlet ducting failures; like oil mist leakage through joints and seepage through hose wall cause high engine oil consumption and most predominantly environment damage. Also to some extent boost leakage in certain operating conditions. These failures reduce the reliability and performance of engine in certain conditions. This paper discusses design and development of cost-effective non-permeable and leak-proof hose-piping system for turbocharged diesel engine where PCV system was connected to air inlet system.

The world today is majorly dependent upon fossil fuels for power generation, of which diesel forms an integral part. Diesel engines, having the highest thermal efficiency of any regular internal or external combustion engine, are widely used in almost all walks of life and cannot be dispensed with in the near future. However, the limited availability of diesel and the adverse effects of diesel engine emissions like nitrogen oxide (NOx) and soot particles raise serious concerns. Hence, their performance and emission improvement continues to be an avenue of great research activity. In this research work, the effects of blending Diethyl Ether with diesel in various proportions (5%, 10%, 15% and 20% by volume) were evaluated on engine performance and emissions of an industrial internal combustion engine.

This paper is in the field of communication networks where different Electronic Control Units (ECUs) communicate with each other using various communication protocols such as Controller Area Network (CAN), Local Interconnect Network (LIN), FlexRay, etc. Typically such types of communication networks are widely used in automobile domain. This paper proposes a holistic approach for evaluation and finalization of complex network architecture for a vehicle. As part of this proposed method, at first one reference-network architecture is constructed for the highest end variant of the vehicle considering all possible ECUs for this vehicle. Then other possible logical variations in network architecture are constructed, which can also technically represent the vehicle's network architecture. Then a set of criteria measures are considered to evaluate how good (or bad) each variation of network architecture is with respect to the reference-network architecture.

Micro Hybrid Systems are a premier approach for improving fuel efficiency and reducing emissions, by improving the efficiency of electrical energy generation, storage, distribution and consumption, yet with lower costs associated with development and implementation. However, significant efforts are required while implementing micro hybrid systems, arising out of components like Intelligent Battery Sensor (IBS). IBS provides battery measurements and battery status, and in addition mission critical diagnostic data on a communication line to micro hybrid controller. However, this set of data from IBS is not available instantly after its initialization, as it enters into a lengthy learning phase, where it learns the battery parameters, before it gives the required data on the communication line. This learning period spans from 3 to 8 hours, until the IBS is fully functional and is capable of supporting the system functionalities.