Search Results

Ti-alloy sheet is a high-modulus elastic-plastic material, about which the resilience in the cold-forming process is quite difficult to control. As a matter of fact, the procedure of cold-forming is composed of many cases such as tensile case and bending case. An expression of ultimate radius for bending-curvature is obtained based on tri-parameters elastic-plastic constitutive model. By classifying the cold-forming process, some typical cases of cold-forming are presented in this paper, and analytical solutions with a high precision of resilience for high-modulus elastic-plastic material such as Ti-alloy sheet under the different typical cases are obtained in this paper. The accurate analytical solutions of resilience for high-modulus elastic-plastic material presented in this paper will contribute to cold-forming process both in the mould-designing and optimizing of cold-forming procedure.

The Forming limit diagram (FLD) is a powerful tool for describing the formability of sheet materials in the automobile industry, which provides fundamental data for die design and Finite Element (FE) simulation. However, traditional FLD testing is typically conducted at quasi-static strain rates from 0.001/s to 0.01/s, which are much lower than the industrial stamping process with strain rates about 1-10/s. In this research, FLDs at various punch speeds (from 1mm/s to 100mm/s or 120mm/s) were obtained for three kinds of AHSS, Quenched and Partitioned steel, Dual Phase 980 and Dual Phase 590 and three kinds of conventional steels, Low Alloy High Strength steel, Bake Hardening steel and IF steel. The results show that FLDs at a typical industrial stamping speed (100mm/s or 120mm/s) are considerably lower than the quasi-static test speed for the Advanced High Strength Steels (AHSS).

In this paper the approach of using modal parameters to detect and locate damage of automobile rear axle under experimental condition is explained. This method uses the changes in the curvature mode of the structure as the damage identification indicator to detect and locate damage. The curvature mode and the damage identification indicator are explained, the process of the identification is introduced. The method is demonstrated with a FEM (Finite Element Method) analysis on a plate under different damage conditions. And the indicator is improved with a weighting function. Then EMA (Experimental Modal Analysis) is conducted on a damaged and an undamaged rear axle of a vehicle to get the modal parameters for the damage identification indicator which later identifies and locates the damages, thus validating the introduced method.

Adhesive bonding has many applications in the automotive industry. The single-lapped bonded joint is the most typically used among various bonding types. This paper presents experimental research for determining the strain field of the single-lapped joint under tensile loading. The materials for the joint are epoxy-based structural adhesive and low-carbon electrolytic zinc steel plate. In the study, a DIC (digital image correlation) system was adopted to measure the strain distribution of the bonded joint during a tensile test. The bonded steel coupons in the tensile test were prepared according to the ASTM standard. During the measurement, images of the coupon joint were taken before and after the deformation process. Then the DIC system measured the strain of bonded joint by comparing two consecutive images. The measured data from the DIC was compared to data taken simultaneously from a traditional extensometer.

Prediction and analysis of the thermo-mechanical coupling behavior in friction braking system is very important for the design and application of vehicle brakes, such as brake judder, brake squeal, brake wear, brake cracks, brake fade. This paper aims to establish a macro-structural model of the thermo-mechanical dynamics of the ventilated disc brake with asymmetrical outer and inner disc thickness, taking into account the friction-velocity curve of the disc pad couple acquired by testing. On the basis of finite elements analysis of the model, the predictions of the thermo-mechanical responses of the brake disc are presented, including disc transient temperature field and normal stress in radial, circular and axial directions, disc lateral deformation and disc thickness variation. Numerical predictions of the disc surface temperature and later distortion are compared with experimental measurements obtained by thermocouples and non-contact displacement sensors.

Research studies have suggested that changes to the ignition system are required to generate a more robust flame kernel in order to secure the ignition process for the future advanced high efficiency spark-ignition (SI) engines. In a typical inductive ignition system, the spark discharge is initiated by a transient high-power electrical breakdown and sustained by a relatively low-power glow process. The electrical breakdown is characterized as a capacitive discharge process with a small quantity of energy coming mainly from the gap parasitic capacitor. Enhancement of the breakdown is a potential avenue effectively for extending the lean limit of SI engine. In this work, the effect of high-power capacitive spark discharge on the early flame kernel growth of premixed methane-air mixtures is investigated through electrical probing and optical diagnosis.

Ion current sensing, which usually employs a spark plug as its sensor to obtain feedback signal from different types of combustion in SI engines, may be applied to HCCI combustion sensing instead of a prohibitively expensive piezoelectric pressure transducer. However, studies showed that the ion current detected by a spark plug sensor is a localized signal within the vicinity of the sensor's electrode gap, being affected by conditions around it. To find out better and feasible ion probe positions, a 3D-CFD model with a detailed surrogate mechanism containing 1423 species and 6106 reactions was employed to study the effect of stratification on ion distribution in HCCI combustion. The simulation results indicate that the monitor probe 1, 8 and 9 are more stable and reliable than the others. IONmax and dIONmax are more accurate to estimate CA50 and dQmax respectively.

In this paper, a new method for determining the forming limit diagram (FLD) of thin sheet metals, called DIC-Grid method, is proposed based on digital image correlation (DIC) technique. It's assumed that there exists one virtual grid with an initial diameter of 2.5mm, which is usually the same dimension as the grid in traditional circular grid analysis, close to the crack of specimen, and the limit strain point on FLD is determined by the deformation of this virtual grid. The DIC-Grid method has been compared with traditional circular grid analysis and the standard ISO/FDIS 12004-2 in Nakajima tests. The results show that the forming limit strains obtained by the newly proposed method are more stable and precise. Furthermore, DIC-Grid method can avoid the measurement error which exists in the circular grid analysis. Meanwhile, it overcomes the shortcomings of time-consuming data processing and non-applicable for unrealistic strain distribution in the method of ISO standard.

Based on the experimental data of true stress-strain measured by DIC (Digital Image Correlation) combined with the data from a tensile test machine, the methodology for establishing a constitutive model for Ti40 alloy sheet is presented in this paper. The procedure is demonstrated by building the constitutive relationship for Ti40 alloy sheet. As the verification of the constitutive relationship, a force-displacement diagram is simulated by FEA (Finite Element Analysis). A comparison of force-displacement diagram obtained separately by FEA and the tensile test machine is made and the result shows that the method for establishing the constitutive relationship for Ti40 alloy sheet presented in this paper are reliable and considerately accurate.

In this study, the orifice inlet rounding radii of four diesel nozzles with different hydro erosive grinding time were measured based on the x-ray CT scan technology provided by Shanghai Synchrotron Radiation Facility (SSRF), and a wide parametrical study of the spray macroscopic behavior in the first 18 mm from the nozzle tip have been carried out with high speed camera. And then the influence of orifice inlet rounding radius on the spray behavior in the near-nozzle field was thoroughly investigated. The investigation results show that: the mean values of orifice inlet rounding radii of different nozzles are measured to be on the order of 21.5-56.8 μm. Although the spray tip penetrations of different nozzles tend to increase with the hydro erosive grinding time through statistical analyzing method, the variations of penetration from nozzles are less than 15% according to different hydro erosive grinding timing.

The weight of an exhaust system on a modern vehicle is increasing because of all kinds of reasons, like engine power's increasing, more catalysts for emission control and more NVH (Noise, Vibration and Harshness) performance requirements. After the engine starting, the exhaust system was not only bearing a cyclical load from the engine, which mainly causing the vibration of the exhaust system, but also the loads from the road, which was transferred through the wheels, the suspension system and the body. Because the exhaust system always worked in these bad conditions, its structural strength, durability and life-time were analyzed in the paper, by numerical simulation and physical correlation. By discretizing the exhaust system's CAD model, a finite element model was built. After restrict the finite element model as it in a real load condition, complete the structure stress analysis and Fatigue analysis of exhaust system's hanger with FEA analysis tools.

In order to explore the generation mechanism of hot-spots on the automotive brake disc, disc tests under non-frictional thermal loads are carried out on the brake dynamometer test bench. In the tests, the oxy-acetylene flame is used as the heat source, and the distribution characteristics of the disc temperature and displacement are measured and analyzed. To confirm the mechanism of the disc deformation, a disc thermal buckling model using finite element method is established, and the key factors for the disc thermal buckling under thermal loads are further analyzed. It is found that the temperature circumferential gradient is small but the temperature radial gradient is large. The disc presents waviness deformation mode with 5th order in circumferential direction, which is the first thermal buckling mode of the disc. A method using spatial frequency spectrum has been proposed to find the critical time and load of thermal buckling.

An ion current sensor is employed in a 4 cylinder production SI engine for combustion diagnosis during combustion process, knock, and low speed pre-ignition (LSPI) detection. The results show that the ion current peak value and ion current peak phase have strong correlation with the cylinder pressure and pressure peak phase respectively. The COV of ion current integral value is greater than the COV of IMEP at the same operating condition. Results show that the ion current signal is sensitive to different lambdas. Using ion current signal, the knock in any given cylinder can be detected. Importantly, the ion sensor successfully detected the low speed pre-ignition (LSPI) about more than 20 °CA before spark ignition.

Similar laser welded blanks with same material and same gauge have been extensive applied in automobile body for improving the material utilization and extending maximum coil size. It is known that, for TWBs with dissimilar material and thicknesses, the difference of material properties and/or thickness of the welded blanks, change of the material properties in the weld seam and heat-affected zones (HAZ) as well as location and orientation of the weld seam are reasons for reduced formability. However, the plastic deformation capacity of TWBs is reduced even when the material and thickness are the same. The aim of this paper is to evaluate the deformation behaviors of similar laser welded joints. Uniaxial tensile of five laser welded joints, with 90°,60°,45°,30°and 0°weld orientations, were tested by using optical measurement-DIC (Digital Image Correlation). Strain /strain ratio distribution and evolution of each joint was analyzed and compared with base material.

For achieving vehicle light weighting, the motion deviation is calculated for substitution of PMMA glazing for inorganic glass. In this paper, a test method is proposed to measure and calculate the motion deviation of the dual-curvature glass. To simulate the dual-curvature glass, the torus surface is fitted with least square method according to the window frame data, which are measured by Coordinate Measuring Machine. By using this method, the motion deviation of PMMA glazing and inorganic glass can be calculated, which can not only validate the effectiveness of motion simulation, but also compare the performances. The results demonstrate that the performance of PMMA glazing is better than that of inorganic glass and the simulation results is validated.

There is an enormous effort to implement safety functionality into battery systems to prevent any accidents with the poisonous and inflammable ingredients of the electrolytes and electrode materials. But not only the safety regulation for lithium ion batteries will be different in comparison to the home electronics application, also the operating strategy must be different to guaranty the required lifetime in the automotive industry up to 10-12 years. This paperwork will show an approach to get offline (on test benches) and/or online (installed inside the car) information regarding the current healthy and state inside the cell. As an approach modeling of physical effects by the help of electro impedance spectroscopy (EIS) will be applied.

Brake pedal feel characteristic is determined by the structural and kinetic parameters of the components of the brake system. As the servo power component of the brake system, vacuum booster has a significant influence on the brake pedal feel. In this paper, a brake system model for brake pedal feel which has a detail vacuum booster mathematical description is established in the software MATLAB/Simulink. The structure gaps, spring preload, friction force and reaction disc characteristics of vacuum booster are considered in this model. A brake pedal feel bench test under different input velocity and vacuum pressure is completed in order to validate the prediction of the model.