Search Results

The vibration characteristics of hybrid vehicles are very different from that of traditional fuel vehicles. In this paper, the active and passive control schemes are used to inhibit the vibration issues in vehicle hybrid powertrain system. Firstly the torsional vibration mechanical model including engine, motor and planetary gear subsystems is established. Then the transient vibration responses of typical working condition are analyzed through power control strategy. Consequently the active and passive control of torsional vibration in hybrid powertrain system is proposed. The active control of the motor and generator torque is designed and the vehicle longitudinal vibration is reduced. The vibration of the planetary gear system is ameliorated with passive control method by adding torsional vibration absorbers to power units. The vibration characteristics in vehicle hybrid powertrain system are effectively improved through the active and passive control.

As the key assembly of new energy vehicles, the noise and vibration, and harshness (NVH) performance of integrated electric drive system directly affects the driving quality of new energy vehicles. In this paper, the vibration noise characteristic test of 3in1 electric drive system is carried out in the semi-muffler chamber. In order to compare and analyze the difference between 2in1 and 3in1 electric drive system NVH performance, the power electronics unit (PEU) in the 3in1 system was removed and placed on the ground away from the platform, and vibration noise test was carried out. In order to analyze the difference of NVH performance between 2in1 status and 3in1 status, the PEU in the 3in1 system was removed and placed on the ground far away from the bench, and the NVH test was carried out. The microphone signal at 1m position and the vibration acceleration signal of the key structural surface of the system are measured experimentally.

Powertrain system of series-parallel hybrid vehicle contains multiple excitation sources like engine, motor and generator. The reduction of noise and vibration is quite difficult during multiplex working modes or the switch of modes. Aiming at Series-parallel hybrid powertrain system which contains engine, motor and planetary gear subsystems, this paper considered a typical working condition which is based on the power control strategy and established the torsional vibration mechanical model of hybrid powertrain system. The inherent characteristics and transient vibration response of the electric mode, hybrid mode and parking charging mode were studied and it was discovered that the repetitive frequency of the powertrain system under the three working modes is the same which is only related to inertia and meshing stiffness of planetary gear system. The non-repetitive frequency and corresponding vibration modes under the electric mode and parking charging mode are both close.

Safety is the cornerstone for Advanced Driver Assistance Systems (ADAS) and Autonomous Driving Systems (ADS). To assess the safety of a traffic situation, it is essential to predict motion states of traffic participants in the future with mathematic models. Accurate vehicle trajectory prediction is an important prerequisite for reasonable traffic situation risk assessment and appropriate decision making. Vehicle trajectory prediction methods can be generally divided into motion model based methods and maneuver model based methods. Vehicle trajectory prediction based on motion models can be accurate and reliable only in the short term. While vehicle trajectory prediction based on maneuver models present more satisfactory performance in the long term, these maneuver models rely on machine learning methods. Abundant data should be collected to train the maneuver recognition model, which increases complexity and lowers real-time performance.

The vehicle permanent magnet synchronous motor has the advantages of high power density, compact structure and small size, which makes it generate heat obviously in the process of energy conversion, which seriously affects the service life of the motor and the performance of permanent magnet. Predicting magnet temperature is a challenging task, in lab and various specialized applications, infrared sensors or thermocouples are used to measure the temperature, but it cost a lot. In order to predict the temperature field of the motor, the hysteresis characteristic test of the core material of the motor is carried out in this paper. The hysteresis characteristic and loss of electrical steel under different temperature, magnetic field intensity and magnetic field frequency are tested. It is found that the loss of electrical steel increases with the increase of magnetic induction intensity and magnetic field frequency.

During light to moderate braking at high speed, the local high temperature phenomenon can be observed on the brake disc surfaces, known as hot spots. The occurrence of hot spots will lead to negative effects such as brake performance fade, thermal judder and local wear, which seriously affect the performance of vehicle NVH. In this paper, based on the bench test of a ventilated disc brake, the basic characteristics of hot spots is obtained and the evolution process of temperature field and disc deformation is analyzed in detail. In temperature field, hot bands appear first and grow, migrate from inner and outer radius to the middle, with the growing temperature fluctuation and finally hot spots appear in the middle radius of the brake disc. The stable SRO waviness forms much earlier than the temperature fluctuation. In the stop brake studied in this paper, the SRO waviness stabilizes in main 7 order state which is lower than the final hot spot order.

The design method for the powertrain mounting system in internal combustion engine vehicles is well-established. Electric vehicles experience higher vibration frequencies and more significant transient responses when accelerating or braking than fuel vehicles due to their high speed and fast response. Therefore, the design of the electric drive assembly mounting system requires further development. The modeling of electric drive assembly mounting systems often neglects the mounting bracket’s influence, which significantly affects the center of mass and rotational inertia of the electric drive assembly. This paper examines the effect of the mounting bracket in the electric drive assembly mounting system. It establishes a mathematical model with six degrees of freedom for the mounting system, considering the mounting bracket. By comparing the natural characteristics and the transient response, it is discussed whether the mass of the mounting bracket greatly influences the system.

Lightweight design is a key factor in general engineering design practice, however, it often conflicts with fatigue durability. This paper presents a way for improving the effectiveness of fatigue performance dominated optimization, demonstrated through a case study on suspension brackets for heavy-duty vehicles. This case study is based on random load data collected from fatigue durability tests in proving grounds, and fatigue failures of the heavy-duty vehicle suspension brackets were observed and recorded during the tests. Multi-objective fatigue optimization was introduced by employing multiaxial time-domain fatigue analysis under random loads combined with the non-dominated sorting genetic algorithm II with archives.

In view of the vibration and noise problem in the electric drive system, the vibration characteristics of its high-speed reducer are analyzed and studied. Through the vibration and noise bench test of the integrated electric drive system, the contribution of high-speed reducer gear meshing order vibration noise to the vibration noise of the electric drive system was studied. A rigid-flexible coupling dynamic model of high-speed reducer was established, and the accuracy of the model was verified. At the same time, based on the gear modification theory, the effects of different gear modification parameters on the peak-to-peak value of high-speed reducer gear transmission error, the amplitude of each order harmonic of the transmission error, and the vibration acceleration response of the high-speed reducer shell surface were studied. Genetic algorithm was used to optimize the gear modification parameters, and the optimization method was simulated and verified.