Search Results

Advanced High Strength Steels (AHSS) have been implemented in the automotive industry to balance the requirements for vehicle crash safety, emissions, and fuel economy. With lower ductility compared to conventional steels, the fracture behavior of AHSS components has to be considered in vehicle crash simulations to achieve a reliable crashworthiness prediction. Without considering the fracture behavior, component fracture cannot be predicted and subsequently the crash energy absorbed by the fractured component can be over-estimated. In full vehicle simulations, failure to predict component fracture sometimes leads to less predicted intrusion. In this paper, the feasibility of using computer simulations in predicting fracture during crash deformation is studied.

Motivated by a combination of increasing consumer demand for fuel efficient vehicles, more stringent greenhouse gas, and anticipated future Corporate Average Fuel Economy (CAFE) standards, automotive manufacturers are working to innovate in all areas of vehicle design to improve fuel efficiency. In addition to improving aerodynamics, enhancing internal combustion engines and transmission technologies, and developing alternative fuel vehicles, reducing vehicle weight by using lighter materials and/or higher strength materials has been identified as one of the strategies in future vehicle development. Weight reduction in vehicle components, subsystems and systems not only reduces the energy needed to overcome inertia forces but also triggers additional mass reduction elsewhere and enables mass reduction in full vehicle levels.

A novel performance classification system has been developed for advanced high-strength steel (AHSS). This system considers intrinsic global and local formability parameters derived from standard uniaxial tension tests and is applicable to all current and future AHSS materials. The overall AHSS performance index (P.I.) is defined herein as the product of the ultimate tensile strength (UTS) and the formability index (F.I.), where F.I. is an intermediate strain value between the true uniform strain and the true fracture strain (TFS). Target P.I. values are defined for First Generation AHSS (GEN1), Improved First Generation AHSS (GEN1+), Third Generation AHSS (GEN3), and AHSS Future. Performance is further distinguished by local, balanced, and global formability characteristics and by relative yield strength (yield-to-tensile ratio). Additionally, the influence of tension test specimen geometry and fracture area measurement method on the TFS value was explored.

Advanced high-strength steels (AHSS), due to their significantly higher strength than the conventional high-strength steels, are increasingly used in the automotive industry to meet future safety and fuel economy requirements. Unlike conventional steels, the properties of AHSS can vary significantly due to the different steelmaking processes and their fracture behaviors should be characterized. In crash analysis, a fracture model is often integrated in the simulations to predict fracture during crash events. In this article, crash simulations including a fracture criterion are conducted for a third-generation AHSS, that is, 980GEN3. A generalized incremental stress state dependent damage model (GISSMO) in LS-DYNA is employed to evaluate the fracture predictability in the crash simulations.

Developing lightweight, stiff and crash-resistant vehicle body structures requires a balance between part geometry and material properties. High strength materials suitable for crash resistance impose geometry limitations on depth of draw, radii and wall angles that reduce geometric efficiency. The introduction of 3rd generation Advanced High Strength Steels (AHSS) can potentially change the relationship between strength and geometry and enable simultaneous improvements in both. This paper will demonstrate applicability of 3rd generation AHSS with higher strength and ductility to replace the 780 MPa Dual Phase steel in a sill reinforcement on the current Jeep Cherokee. The focus will be on formability, beginning with virtual simulation and continuing through a demonstration run on the current production stamping tools and press.

To evaluate vehicle crash performance in the early design stages, a reliable fracture model is needed in crash simulations to predict material fracture initiation and propagation. In this paper, a generalized incremental stress state dependent damage model (GISSMO) in LS-DYNA® was calibrated and validated for a 780-MPa third generation advanced high strength steels (AHSS), namely 780 XG3TM steel that combines high strength and ductility. The fracture locus of the 780 XG3TM steel was experimentally characterized under various stress states including uniaxial tension, shear, plane strain and equi-biaxial stretch conditions. A process to calibrate the parameters in the GISSMO model was developed and successfully applied to the 780 XG3TM steel using the fracture test data for these stress states.

Considerable improvements can be obtained in battery performance for hybrid electric vehicles (HEVs) by employing an electrochemistry-transport model based on a multi-physics modeling framework and ultrafast numerical algorithms. One important advantage of this approach over the lumped equivalent circuit (or look-up table) approach is the ability of the former to adapt to changes in design and control. In this work, we present mathematical and numerical details of our approach, and demonstrate the robustness of this battery model in simulation of short-pulse charge/discharge characteristic of HEV driving cycles under room and low temperatures.

The pressure of the combustion gas in a diesel engine is higher than that in a gasoline engine, so the cylinder head gasket that seals the combustion chamber is exposed to a severe environment. The sealability of the gaskets is affected not only by the gasket specifications, but also by the cylinder head, cylinder block, and the head bolts that clamp them. Consequently, in order to improve the performance of these gaskets, it is essential to enhance their material characteristics. Because the necessary characteristics of a gasket material are high strength and high fatigue strength, methods of realizing these enhancements were studied, and a new material was developed. It was confirmed that a gasket made using the newly developed material withstood high combustion pressure, and the gasket was used in a high performance diesel engine.

Advanced high strength steels (AHSS) have been widely accepted as a material of choice in the automotive industry to balance overall vehicle weight and stringent vehicle crash test performance targets. Combined with efficient use of geometry and load paths through shape and topology optimization, AHSS has enabled vehicle manufacturers to obtain the highest possible ratings in safety evaluations by the Insurance Institute for Highway Safety (IIHS) and the National Highway Traffic Safety Administration (NHTSA). In this study, vehicle CAE side impact models were used to evaluate three side impact crash test conditions (IIHS side impact, NHTSA LINCAP and FMVSS 214 side pole) and the IIHS roof strength test condition and to identify several key components affecting the side impact test performance. HyperStudy® optimization software and LS-DYNA® nonlinear finite element software were utilized for shape and gauge optimization.

The use of advanced high strength steels (AHSS) such as dual phase (DP), transformation induced plasticity (TRIP) and stretch flanging (SF) steels of the tensile strength of 600 MPa range are well established in automotive components production. This is due to their superior crash energy absorption ability and vehicle weight reduction potential. Recent trends show rapid growth in applications of even higher strength grades such as 800 MPa and 1000 MPa tensile strength and above. They are mostly used for fabrication of crash sensitive components to meet much higher safety requirements in side impact and roll-over accidents. One of the few concerns during the fabrication of AHSS components is the formability limit in flanging and hole expansion operations. Questions have been raised about the applicability of existing manufacturing experience with conventional high strength low alloy steels (HSLA) to new generations of AHSS.

Because of their excellent crash energy absorption capacity, dual phase (DP) steels are gradually replacing conventional High Strength Low Alloy (HSLA) steels for critical crash components in order to meet the more stringent vehicle crash safety regulations. To achieve optimal axial and bending crush performance using DP steels for crash components designed for crash energy absorption and/or intrusion resistance applications, the cross sections need to be optimized. Correlated crush simulation models were employed for the cross-section study. The models were developed using non-linear finite element code LS-DYNA and correlated to dynamic and quasi-static axial and bending crush tests on hexagonal and octagonal cross-sections made of DP590 steel. Several design concepts were proposed, the axial and bending crush performance in DP780 and DP980 were compared, and the potential mass savings were discussed.

More and more advanced high strength steels (AHSS) such as dual phase steels and TRIP steels are implemented in automotive components due to their superior crash performance and vehicle weight reduction capabilities. Recent trends show increased applications of higher strength grades such as 780/800 MPa and 980/1000 MPa tensile strength for crash sensitive components to meet more stringent safety regulations in front crash, side impact and roll-over situations. Several issues related to AHSS stamping have been raised during implementation such as springback, stretch bending fracture with a small radius to thickness ratio, edge cracking, etc. It has been shown that the failure strains in the stretch bending fracture and edge cracking can be significantly lower than the predicted forming limits, and no failure criteria are currently available to predict these failures.

As we continue to create ever-lighter road vehicles, the challenge of balancing weight reduction and structural performance also continues. One of the key parts this occurs on is the hood, where lighter materials (e.g. aluminum) have been used. However, the aerodynamic loads, such as hood lift, are essentially unchanged and are driven by the front fascia and front grille size and styling shape. This paper outlines a combination CFD/FEA prediction method for hood deflection performance at high speeds, by using the surface pressures as boundary conditions for a FEA linear static deflection analysis. Additionally, custom post-processing methods were developed to enhance flow analysis and understanding. This enabled the modification of existing test methods to further improve accuracy to real world conditions. The application of these analytical methods and their correlation with experimental results are discussed in this paper.

Magnetorheological (MR) dampers have been used in the market on various vehicles since 2001. They use a special oil-based fluid (Magnetorheological Fluid, MRF) that contains small iron particles (1-10 μm in size) and a controllable electromagnetic piston to allow a wide range of damping forces. The system's wide range of available damping force combined with nearly instantaneous response time helps maximize body control while simultaneously providing outstanding ride comfort. This paper describes how the MR technology was combined with conventional suspension tuning to achieve an enhanced level of dynamic performance. While the MR damper offers enhanced performance, its unique response characteristics require tuning of other hardware components that could be considered to be beyond the normal tuning range for that of a conventional suspension.

Forming Limit Diagrams (FLD) have been widely and successfully used in sheet metal stamping as a failure criterion to detect localized necking, which is the most common failure mechanism for conventional steels during forming. However, recent experience from stamping Dual-Phase steels found that, under certain circumstances such as stretching-bend over a small die radius, the sheet metal fails earlier than that predicted by the FLD based on the initiation of a localized neck. It appears that a different failure mechanism and mode are in effect, commonly referred to as “shear fracture” in the sheet metal stamping community. In this paper, experimental and numerical analysis is used to investigate the shear fracture mechanism. Numerical models are established for a stretch-bend test on DP780 steel with a wide range of bend radii for various failure modes. The occurrences of shear fracture are identified by correlating numerical simulation results with test data.

As a result of the increasing usage of high strength steels in automotive body structures, a number of formability issues, particularly bend and edge stretch failures, have come to the forefront of attention of both automotive OEMs and steel makers. This investigation reviews these stamping problems and attempts to identify how certain material properties and microstructural features relate to forming behavior. Various types of dual phase steels were evaluated in terms of tensile, bending, hole expansion, limiting dome height, and impact properties. In addition, the key microstructural differences of each grade were characterized. In order to understand the material behavior under practical conditions, stamping trials were conducted using actual part shapes. It was concluded that material properties can be optimized to maximize local formability in stamping applications. The results also emphasize that the dual phase classification can encompass a broad range of property variations.

Springback is a major concern in stamping of advanced high strength steels (AHSS). The existing computer simulation technology has difficulty predicting this phenomenon accurately even though it is well developed for formability simulations. Great efforts made in recent years to improve springback predictions have achieved noticeable progress in the computational capability and accuracy. In this work, springback simulation studies are conducted using FEA software LS-DYNA®. Various parametric sensitivity studies are carried out and key variables affecting the springback prediction accuracy are identified. Recently developed simulation technologies in LS-DYNA® are implemented including dynamic effect minimization, smooth tool contact and newly developed nonlinear isotropic/kinematic hardening material models. Case studies on lab-scale and full-scale industrial parts are provided and the predicted springback results are compared to the experimental data.

Today's fuel cell powered vehicles typically utilize compressed hydrogen storage systems with a nominal working pressure of either 35MPa or 70Mpa. This coexistence of working pressures has, in a large part, developed in isolation, in that automakers have primarily considered vehicle side issues when choosing the storage system pressure. This study looks at hydrogen fueling from a holistic perspective by considering both vehicle side and station side issues with the goal to determine an optimum hydrogen working pressure. The approach utilized is to first conduct a data driven study of vehicle fueling at different working pressures and ambient temperatures to determine the vehicle and thermodynamic considerations of hydrogen fueling. This data is then contrasted with the hydrogen station hardware required to perform fueling at these temperatures and pressures.

The purpose of the recyclability pilot project was to evaluate and confirm the reality of reuse, material recycling and landfill potential of parts and components over a range of Honda vehicles by model and year. A total of 18 vehicles, model years ranging from 1982 to 2001, were selected for study and processed at two automotive recycling centers and a scrap metal processing facility with an automotive shredder. The automotive dismantlers identified which parts and components were removed for reuse or remained with the hulk for further processing at an automotive shredder facility. Dismantling times and part weights were recorded and dismantling procedures were videotaped. The remaining hulks were delivered to the scrap metal processing facility for further processing. After shredding, the ferrous, nonferrous and landfill materials were separately collected for determining weights of these different process outputs.

Advanced high strength steels (AHSS), such as dual phase (DP) and transformation induced plasticity (TRIP) steels, have been used successfully for making light weight vehicles and their usage is growing. Now, the automotive industry is expanding the use of AHSS to higher strength levels for further mass reduction. In a 2003 SAE paper, the material and formability characteristics for such steels were presented for steel grades of DP980, high yield type DP780 (780YM), low yield type DP780 (780YL), TRIP780, and TRIP590. In this study, experiments were conducted to assess the formability of these high strength steels using a T-channel, which incorporates several different forming modes in automotive stamping. The feasibility of computer simulation technology for the formability analyses of AHSS is also addressed.