Search Results

This paper investigates an optimal design of a diesel engine and after-treatment systems for a series hybrid electric forklift application. A holistic modeling approach is developed in GT-Suite® to establish a model-based hardware definition for a diesel engine and an after-treatment system to accurately predict engine performance and emissions. The used engine model is validated with the experimental data. The engine design parameters including compression ratio, boost level, air-fuel ratio (AFR), injection timing, and injection pressure are optimized at a single operating point for the series hybrid electric vehicle, together with the performance of the after-treatment components. The engine and after-treatment models are then coupled with a series hybrid electric powertrain to evaluate the performance of the forklift in the standard VDI 2198 drive cycle.

Accurate individual cylinder Air Fuel Ratio (AFR) feedback provide opportunities for improved engine performance and reduced emissions in spark ignition engines. One potential measurement for individual cylinder AFR is in-cylinder ionization measured by employing the spark plug as a sensor. A number of previous investigations have studied correlations of the ionization signal with AFR and shown promising results. However the studies have typically been limited to single cylinders under restricted operating conditions. This investigation analyzes and characterizes the ionization signals in correlation to individual AFR values obtained from wide-band electrochemical oxygen sensors located in the exhaust runners of each cylinder. Experimental studies for this research were conducted on a 2.0L inline 4 cylinder spark ignited engine with dual independent variable cam phasing and an intake charge motion control valve.

An accurate estimation of cycle-by-cycle in-cylinder mass and the composition of the cylinder charge is required for spark-ignition engine transient control strategies to obtain required torque, Air-Fuel-Ratio (AFR) and meet engine pollution regulations. Mass Air Flow (MAF) and Manifold Absolute Pressure (MAP) sensors have been utilized in different control strategies to achieve these targets; however, these sensors have response delay in transients. As an alternative to air flow metering, in-cylinder pressure sensors can be utilized to directly measure cylinder pressure, based on which, the amount of air charge can be estimated without the requirement to model the dynamics of the manifold.

Measurement of internal combustion engine air flow is challenging due to the required modification of the intake system and subsequent change in the air flow pattern. In this paper, various surge tank volumes were investigated to improve the accuracy of measuring air flow rate into a 674-cm3, four-stroke, liquid-cooled, internal combustion engine. According to the experimental results, when the venturi meter is used to measure the intake air flow rate, an air surge tank is required to be installed downstream of the venturi to smoothen the air flow. Moreover, test results revealed that increasing air surge tank volume beyond a limit could have a negative effect on the engine performance parameters especially in carbureted engines where controlling AFR is difficult. Although the air flow rate into the engine changed with increasing tank volume, the air-fuel ratio was leaner for smaller tank volumes.

The increased availability of natural gas (NG) in the United States (US) and its relatively low cost versus diesel fuel has increased interest in the conversion of medium duty (MD) and heavy duty (HD) engines to NG fueled combustion systems. The aim for development for these NG engines is to realize fuel cost savings and increase operating range while reduce harmful emissions and maintaining durability. Traditionally, port-fuel injection (PFI) or premixed NG spark-ignited (SI) combustion systems have been used for light duty LD, and MD engines with widespread use in the US and Europe [1]. However, this technology exhibits poor thermal efficiency and is load limited due to knock phenomenon that has prohibited its use for HD engines. Spark Ignited Direct Injection (SIDI) can be used to create a partially stratified combustion (PSC) mixture of NG and air during the compression stroke.

The exhaust emissions of off-road and utility engines have recently come under increasingly thorough scrutiny and are now becoming the subject of federal regulations. While the most straightforward emissions guidelines relate to steady-state engine performance, it is well known that duty cycles of many small engines have a transient content and that its significance can vary strongly from application to application. Hence, it is important to examine how measured emissions change when the transient content of a test cycle is varied, and what kinds of steady-state and transient test cycles might realistically imitate operational conditions. These questions have been addressed in an experimental study in which several small two- and four-stroke engines have been tested under steady state and transient cycles. The same tests were also carried out when these engines had been adjusted to operate at leaner air-fuel ratios, as might be required by forthcoming regulations.

The increased availability of natural gas (NG) in the United States (US) and its relatively low cost compared to diesel fuel has heightened interest in the conversion of medium duty (MD) and heavy duty (HD) engines to NG fueled combustion systems. The aim for development for these NG engines is to realize fuel cost savings and reduce harmful emissions while maintaining durability. Transforming part of the vehicle fleet to NG is a path to reduce dependence on crude oil. Traditionally, port-fuel injection (PFI) or premixed NG spark-ignited (SI) combustion systems have been used for MD and HD engines with widespread use in the US and Europe. But this technology exhibits poor cycle efficiency and is load limited due to knock phenomenon. Direct Injection of NG during the compression stroke promises to deliver improved thermal efficiency by avoiding excessive premixing and extending the lean limits which helps to extend the knock limit.

Early exhaust valve opening (eEVO) increases the exhaust gas temperature by faster termination of the power stroke and is considered as a potential warm up strategy for diesel engines aftertreatment thermal management. In this study, first, it is shown that when eEVO is applied, the engine main variables such as the boost pressure, exhaust gas recirculation (EGR) and injection (timing and quantity) must be re-calibrated to develop the required torque, avoid exceeding the exhaust temperature limits and keep the air fuel ratio sufficiently high. Then, a two-step procedure is presented to optimize the engine operation after the eEVO system is introduced, using a validated diesel engine model. In the first step, the engine variables are optimized at a constant eEVO shift. In the second step, optimal eEVO trajectories are calculated using Dynamic Programming (DP) for a transient test cycle.

With stringent emission regulations, many subsystems that abate engine tailpipe-out emissions become a necessary part for engines. The increased level of complexity poses technical challenges for the quality and reliability for modern engines. Among the spectrum of quality control methodologies, one conventional methodology focuses on every component's quality to ensure that the accumulative deviation is within predetermined limits. This conventional methodology tightens the component tolerance during the manufacturing process and typically results in increased cost. Another conventional methodology that is on the other side of the spectrum focuses on tailoring an engine calibration solution to offset the manufacturing differences. Although the tailored engine calibration solution reduces manufacturing cost for components, it increases the development and validation cost for engines. Given the cost and time constraints, system integration plays an important role in engine development.

In order to further understand the sequence of events leading to stochastic preignition in a spark-ignition engine, a methodology previously developed by the authors was used to evaluate the propensity of a wide range of fuels to establishing propagating flames under conditions representative of those at which stochastic preignition (SPI) occurs. The fuel matrix included single component hydrocarbons, binary mixtures, and real fuel blends. The propensity of each fuel to establish a flame was correlated to multiple fuel properties and shown to exhibit consistent blending behaviors. No single parameter strongly predicted a fuel’s propensity to establish a flame, while multiple reactivity-based parameters exhibited moderate correlation. A two-stage model of the flame establishment process was developed to interpret and explain these results.

Wall wetting of injected fuel onto the intake manifold and cylinder wall causes unpredictable transient behavior of air-fuel mixing which results in a significant emission of unburned hydrocarbon (HC) emission during cold start operation. Heated exhaust gas oxygen (HEGO) sensors cannot measure the air-fuel ratio (A/F) of exhaust gas during cold start condition. Precise and fast estimation of air/fuel ratio of the exhaust gas is required to elucidate the wall wetting phenomena and subsequent HC formation. Refined A/F estimation can enable the control of fuel injection minimizing HC emissions during cold start conditions so that HC emissions can be minimized. A new estimator for A/F of the exhaust gas has been developed. The A/F estimator described in this study utilizes measured exhaust gas temperature and general engine parameters such as engine speed, airflow, coolant temperature, etc.