Search Results

Adoption of high-pressure common-rail (HPCR) fuel systems, which subject diesel fuels to higher temperatures and pressures, has brought into question the veracity of ASTM International specifications for biodiesel and biodiesel blend oxidation stability, as well as the lack of any stability parameter for diesel fuel. A controlled experiment was developed to investigate the impact of a light-duty diesel HPCR fuel system on the stability of 20% biodiesel (B20) blends under conditions of intermittent use and long-term storage in a relatively hot and dry climate. B20 samples with Rancimat induction periods (IPs) near the current 6.0-hour minimum specification (6.5 hr) and roughly double the ASTM specification (13.5 hr) were prepared from a conventional diesel and a highly unsaturated biodiesel. Four 2011 model year Volkswagen Passats equipped with HPCR fuel injection systems were utilized: one on B0, two on B20-6.5 hr, and one on B20-13.5 hr.

Two optical techniques were developed and combined with a CFD simulation to obtain spatio-temporally resolved information on air/fuel mixing in the cylinder of a methane-fueled, fired, optically accessible engine. Laser-induced fluorescence (LIF) of anisole (methoxybenzene), vaporized in trace amounts into the gaseous fuel upstream of the injector, was captured by a two-camera system, providing one instantaneous image of the air/fuel ratio per cycle. Broadband infrared (IR) absorption by the methane fuel itself was measured in a small probe volume via a spark-plug integrated sensor, yielding time-resolved quasi-point information at kHz-rates. The simulation was based on the Reynolds-averaged Navier-Stokes (RANS) approach with the two-equation k-epsilon turbulence model in a finite volume discretization scheme and included the port-fuel injection event. Commercial CFD software was used to perform engine simulations close to the experimental conditions.

In this paper, the experimental and numerical simulation of the flow field in the simplified front wheel arch of a scaled-down VW Phaeton half-model (scale 1:2,5) is presented. For wind tunnel experiments a realistic, rotating wheel model with plexiglass treads (PMMA) was designed. The construction allowed for detailed measurements of the flow field directly at the brake disk by means of the stereoscopic Particle Image Velocimetry (PIV) technique. The formation of the flow structures and the resulting three-dimensional boundary layers on the brake disk are analyzed. Furthermore, the oncoming air flow towards the brake disk and the flow field near the wheel rim openings were investigated. The experimental data is compared with results of Computational Fluid Dynamics (CFD) simulations using the Lattice-Boltzmann based solver Powerflow. The validation shows the potential and the limitations of the numerical approach and indicates areas of further improvement.

This paper presents a complete methodology for performing finite-volume-based detached-eddy simulation for the prediction of aerodynamic forces and detailed flow structures of passenger vehicles developed using the open-source CFD toolbox OpenFOAM®. The main components of the methodology consist of an automatic mesh generator, a setup and initialisation utility, a DES flow solver and analysis and post-processing routines. Validation of the predictions is done on the basis of detailed comparisons to experimental wind-tunnel data. Results for lift and drag are found to compare favourably to the experiments, with some moderate discrepancies in predicted rear lift. Point surface-pressure measurements, oil-streak images and maps of total pressure in the flow field demonstrate the approach's capabilities to predict the fine detail of complex flow regimes found in automotive aerodynamics.

The need to reduce weight of large and heavy components used by the automotive and aerospace industries such as engine block, cylinder head cover and helicopter gearbox housing has led to the development of new Mg gravity casting alloys that provide adequate properties and cost effective solution. The new Mg gravity casting alloys are designed for high stressed components that operate at a temperature up to 300°C. These new alloys exhibit excellent mechanical properties and creep resistance in T-6 conditions. The present paper aims at introducing three new Mg gravity casting alloys designated MRI 201S, MRI 202S and MRI 203S, which were recently developed by the Magnesium Research Institute of DSM and VW. Apart from the excellent high temperature performance of these alloys, they provide adequate castability and dimension stability along with good weldability and corrosion resistance.

For substantial reduction of fuel consumption of their vehicle fleet, Volkswagen AG has decided to develop spark-ignition engines with direct fuel injection. To launch this new engine concept with stratified lean operation mode while at the same time meeting the stringent EU IV emission standards, it was necessary to develop a suitable exhaust gas aftertreatment system. This was achieved as part of an intensive co-operation between Volkswagen AG and OMG, formerly dmc2 Degussa Metals Catalysts Cerdec AG. The paper describes the demands for exhaust gas aftertreatment due to lean burn operation. In addition the main development steps of the exhaust gas aftertreatment system for Volkswagen FSI engines and catalyst durability over vehicle lifetime are discussed. Focus is laid on the catalyst system design and coating variations. Volkswagen developed a new closed-loop emission control management system which uses NOx-sensor signals for the first time worldwide.

The EPEFE study (European Programme on Emissions, Fuels and Engine Technologies), /1/ and other programmes have identified an increase in tailpipe NOx emissions with reduced gasoline aromatics content for modern 3-way controlled catalyst vehicles. This effect occurs with fully warmed-up catalyst under closed-loop operation. In order to understand the reasons for this effect VW and Shell have mechanistically investigated the effects of fuel properties on EMS (engine management system) and catalyst performance. Fuels with independent variation of oxygen, aromatics and mid-range volatility were tested in different VW engines. λ was monitored using sensors located both pre and post catalyst. The results confirmed that reducing gasoline aromatics content reduced engine-out emissions but increased tailpipe NOx emissions. It could be shown that differences in H/C ratio led to differences in the hydrogen content of engine-out emissions which affected the reading of the λ sensor.

This paper summarizes the validation of prototype vehicle-to-infrastructure (V2I) safety applications based on Dedicated Short Range Communications (DSRC) in the United States under a cooperative agreement between the Crash Avoidance Metrics Partners LLC (CAMP) and the Federal Highway Administration (FHWA). After consideration of a number of V2I safety applications, Red Light Violation Warning (RLVW), Curve Speed Warning (CSW) and Reduced Speed Zone Warning with Lane Closure Warning (RSZW/LC) were developed, validated and demonstrated using seven different vehicles (six passenger vehicles and one Class 8 truck) leveraging DSRC-based messages from a Road Side Unit (RSU). The developed V2I safety applications were validated for more than 20 distinct scenarios and over 100 test runs using both light- and heavy-duty vehicles over a period of seven months. Subsequently, additional on-road testing of CSW on public roads and RSZW/LC in live work zones were conducted in Southeast Michigan.

VOLKSWAGEN has conducted a number of investigations on a Multi Fuel Vehicle (MFV), designed for variable fuel operation, to determine the influence of fuel composition and clean fuels on exhaust emissions, mainly on ozone forming potential. Results of the tests indicate a small advantage of Phase II Reformulated Gasoline and a greater one for for methanol fuel M85, compared to today's gasoline. For M85 there is an about 25 % lower ozone forming potential. The most critical components in the exhaust of methanol fueled vehicles (M85) are unburned methanol and formaldehyde, forming more than 60 % of the total ozone forming potential. Therefore improvement of cold start and warmup driving during the first two to three minutes is of great importance, because in this time about 90 % of the mentioned components are formed.

A recently developed Laser Raman Scattering system was applied to measure the in-cylinder air-fuel ratio and the residual gas content (via the water content) of the charge simultaneously in a firing spark-ignition engine during cold start and warm-up. It is the main objective of this work to elucidate the origin of misfires and the necessity to over-fuel at cool ambient temperatures. It turns out that the overall air-fuel ratio and residual gas content (in particular the residual water content) of the charge appear to be the most important parameters for the occurrence of misfires (without appropriate fuel enrichment), i.e., the engine behaviour from cycle to cycle becomes rather predictable on the basis of these data. An alternative explanation for the necessity to over-fuel is given.

Laser-induced exciplex fluorescence has been applied to the mixture formation process in the combustion chamber of an optically-accessible four-cylinder in-line spark-ignition engine in order to distinguish between liquid and vapor fuel distribution during the intake and compression stroke for different injection timings. The naphthalene/N,N,N′N′-tetramethyl p-phenylene diamine (TMPD) exciplex system excited at 308nm with a broadband XeCl excimer laser is used to obtain spectrally-separated, single-shot fluorescence images of the liquid or vapor phase of the fuel. For different timings of the fuel injector this technique is applied to obtain crank-angle-resolved images of the resulting mixture in the combustion chamber. The fluorescence light is detected with an intensified slow-scan CCD-camera equipped with appropriate filters.

Mixture formation analysis in the combustion chamber of a slightly modified mass-production SI engine with port-fuel injection using nonintrusive laser measurement techniques is presented. Laser Raman scattering and planar laser-induced tracer fluorescence are employed to measure air-fuel ratio and residual gas content of the charge with and without spatial resolution. Single-cycle measurements as well as cycle-averaged measurements are performed. Engine operation parameters like load, speed, injection timing, spark timing, coolant temperature, and mean air-fuel ratio are changed to study whether the effects on mixture formation and engine performance can be resolved by the applied laser spectroscopic techniques. Mixture formation is also analyzed by measurement of the charge composition as a function of crank angle. Clear correlations of the charge composition data and engine operating conditions are seen.

Quantitative 1-D spatially-resolved NO LIF measurements in the combustion chamber of a mass-production SI engine with port-fuel injection using a tunable KrF excimer laser are presented. One of the main advantages of this approach is that KrF laser radiation at 248 nm is only slightly absorbed by the in-cylinder gases during engine combustion and therefore it allows measurements at all crank angles. Multispecies detection turned out to be crucial for this approach since it is possible to calculate the in-cylinder temperature from the detected Rayleigh scattering and the simultaneously acquired pressure traces. Additionally, it allows the monitoring of interfering emissions and spectroscopic effects like fluorescence trapping which turned out to take place. Excitation with 248 nm yields LIF emissions at shorter wavelengths than the laser wavelength (at 237 and 226 nm).

In direct-injection gasoline (GDI) engines with charge stratification, minimizing engine-out nitrogen oxide (NOx) emission is crucial since exhaust-gas aftertreatment tolerates only limited amounts of NOx. Reduced NOx production directly lowers the frequency of energy-inefficient catalyst regeneration cycles. In this paper we investigate NO formation in a realistic GDI engine. Quantitative in-cylinder measurements of NO concentrations are carried out via laser-induced fluorescence imaging with excitation of NO (A-X(0,2) band at 248 nm), and subsequent fluorescence detection at 220-240 nm. Engine modifications were kept to a minimum in order to provide results that are representative of practical operating conditions. Optical access via a sapphire ring enabled identical engine geometry as a production line engine. The engine is operated with commercial gasoline (“Super-Plus”, RON 98).

The prevention of any brake noise or brake-induced body vibrations is a key development target firmly integrated in the car development process. Emphasis is placed here on disc brake judder that is attributable to thickness variations in the disc. These deviations from the ideal plane surface can be caused either by wear and corrosion or by thermal stresses (changes within the microstructure of the disc material). They are termed “cold judder” and “thermal judder” respectively. During braking, possible vibration excitation passes through a wide frequency band due to the coupling between the judder frequency and the wheel rotational speed, and thus, resonant frequencies of many vehicle components can be excited. This includes wheel suspension components and the steering column. In this paper, it is reported on extensive investigations into the topic of “cold judder”.

Sulfur content in gasoline is known to reduce the efficiency of the catalytic converters that are used to reduce pollutants in the exhaust gas of cars. There is some concern that nitrous oxide emissions (N2O) increase when fuel with a high sulfur content is used. The engine out and tailpipe mass emissions of two cars conforming to the California LEV-standard were analyzed. The influence of the fuel sulfur content on the emissions of the regulated and some unregulated pollutants during FTP test cycles was determined. Four fuels covering the range from less than 1 to 330 ppm sulfur content were used. Over that range of fuel sulfur concentration the engine out emissions of sulfur dioxide (SO2 ) of both cars increased. Tailpipe emissions of SO2 were only found at fuel sulfur concentrations of 150 and 330 ppm. For both vehicles a correlation between the N2O emissions and the fuel sulfur content was found.

In a consortium of European industrial partners and research institutes, a combination of industrial development and scientific research was organised. The objective was to improve the catalytic NOx conversion for lean burn cars and heavy-duty trucks, taking into account boundary conditions for the fuel consumption. The project lasted for three years. During this period parallel research was conducted in research areas ranging from basic research based on a theoretical approach to full scale emission system development. NOx storage catalysts became a central part of the project. Catalysts were evaluated with respect to resistance towards sulphur poisoning. It was concluded that very low sulphur fuel is a necessity for efficient use of NOx trap technology. Additionally, attempts were made to develop methods for reactivating poisoned catalysts. Methods for short distance mixing were developed for the addition of reducing agent.

The reduction of both harmful emissions (CO, HC, NOx, etc.) and gases responsible for greenhouse effects (especially CO2) are mandatory aspects to be considered in the development process of any kind of propulsion concept. Focusing on ICEs, the main development topics are today not only the reduction of harmful emissions, increase of thermodynamic efficiency, etc. but also the decarbonization of fuels which offers the highest potential for the reduction of CO2 emissions. Accordingly, the development of future ICEs will be closely linked to the development of CO2 neutral fuels (e.g. biofuels and e-fuels) as they will be part of a common development process. This implies an increase in development complexity, which needs the support of engine simulations. In this work, the virtual modeling of real fuel behavior is addressed to improve current simulation capabilities in studying how a specific composition can affect the engine performance.

The measurement of 3D coordinates using optical techniques is well known for more than 50 years. Today, modern photogrammetric systems are based on handheld digital cameras and are used to identify the location of any circular marker or feature on the object's surface. The ease of use and the accurate and automated derivation of 3D coordinates from 2D digital images helped to establish a powerful tool for position control, assembly checks and reverse engineering. A new application is the analysis of real vehicle crashes. The location of hundreds of markers on the damaged vehicle can easily be determined in vehicle body position. These coordinates are being compared to the undeformed geometry and provide herby 3D information on any displacement. Using reverse engineering techniques, surfaces are created from the 3D points and thus a 3D model of the crashed vehicle is available for an easy visualization of the deformation.

This paper reports on a non-intrusive method for measuring the liquid fuel film thickness in the intake manifold of a series production SI engine with multi-point fuel injection. The technique is based on laser-induced fluorescence. The optical set-up uses a bifurcated optical fibre bundle for transmission of the laser light for excitation of the fluid and for detecting of the fluorescence light. Due to the special design of the optical probe head it is highly sensitive for thin film measurements and it allows the accurate determination of the fuel film thickness even between a few and 100 μm. Special emphasis is placed on the selection of an adequate tracer added to the iso-octane fuel to achieve the correct film thickness even under vaporizing conditions, and on a detailed study of the parameters influencing the evaluated film thickness.