Search Results

This SAE Information Report describes results of testing of the SAE J1746 ISP-Vehicle Standard for the communication of spatial data references between central sites and mobile vehicles on roads. Testing was performed by the Oak Ridge National Laboratory and its contractors, resulting in a document from which this Information Report has been extracted. Tests were performed by computer analysis and corroborated by field tests with a mobile vehicle.

This document specifies the interface and the behavior of the VHDL-AMS packages for use in modeling statistical behavior. These packages are useful in defining the statistical variation of parameters of electrical, electronic, and mechatronic components and sub-systems. These can then be used with simulation tools to analyze the performance and reliability of systems composed of these components and sub-systems. Providing a standard definition of the package interfaces and their behavior is intended to facilitate the exchange of models between component and system manufacturers and the use of different CAE simulation tools. The SAE statistical package supports the statistical modeling of design parameters subject to tolerances for designs described using the VHDL or VHDL-AMS languages.

No Scope Available

This Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the power brake booster systems provided as original equipment of motor vehicles. These modifications are generically called "Reduced Effort Power Brakes" (REPB) The purpose of the modification is to lower the amount of driver effort required to apply the brakes. Retention of reliability, ease of use and maintainability for disabled drivers, passengers, and the general public is of primary concern. Reduced Effort Power Brake modifications should be qualified by the tests referenced in the Recommended Test Procedure. The tests set forth in that procedure should be applied, and failure of a Reduced Effort Power Brake modification to meet those tests should disqualify the modification from the claim of meeting the specifications of this Information Report.

The modeling requirements listed in this document provide guidelines for specifying: Analysis requirements Computer-Aided Engineering (CAE) simulator Model fidelity System assumptions Model architecture Validation requirements Deliverables for electrical/electronic components and the integral interfacing systems (mechanical, thermal, hydraulic) associated with these components. The simulation models are primarily intended to facilitate functional specification and operational evaluation between component and system manufacturers, and are not intended to otherwise constrain or restrict the use of CAE simulation tools for automotive design, analysis and validation.

A subcommittee within SAE ISTC Division 35 has written this report to provide automotive engineers and designers a basic understanding of the design considerations and high temperature material availability for exhaust manifold use. It is hoped that it will constitute a concise reference of the important characteristics of selected cast and wrought ferrous materials available for this application, as well as methods employed for manufacturing. The different types of manifolds used in current engine designs are discussed, along with their range of applicability. Finally, a general description of mechanical, chemical, and thermophysical properties of commonly-used alloys is provided, along with discussions on the importance of such properties.

A subcommittee within SAE ISTC Division 35 has written this report to provide automotive engineers and designers a basic understanding of the design considerations and high temperature material availability for exhaust manifold use. It is hoped that it will constitute a concise reference of the important characteristics of selected cast and wrought ferrous materials available for this application, as well as methods employed for manufacturing. The different types of manifolds used in current engine designs are discussed, along with their range of applicability. Finally, a general description of mechanical, chemical, and thermophysical properties of commonly-used alloys is provided, along with discussions on the importance of such properties.

This SAE Information Report describes requirements gathering workshops for Public Sector use of ITS Referencing Datums.

This SAE Standard outlines the US standard for sending Advanced Traveler Information Services (ATIS) messages over various Bandwidth Reduced Media (BRM). It specifies the “over the air” format and method for such data messages at a bit level. The methodology allows a cooperative sharing of the media’s total bandwidth with other non-ATIS data services. It allows for further expansion to other ATIS messages such as transit schedules and weather use. It uses a common directory of messages to divide out those messages which are the subject of this specification from others. It is built upon the concept of “waveform neutrality” in that it can be hosted by a wide variety of media often found in the delivery of wireless data services (although it is also useful for wire line applications). This message set is incorporated into each medium (“host medium”) by a formatting process specific to each media. A graphical overview ofthis process is shown in Figure 1.

This SAE standard establishes the minimum construction and performance requirements for a combination cable consisting of 11 conductors and 4 twisted pairs for use on trucks, trailers, and dollies in conjunction with SAEJ2691. (15 pole connectors.) The cable includes both power and unjacketed SAE J1939-15 paired signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.

This document establishes standard graphical symbols and color conventions for use in either still (static) or animated graphics used for communicating service information. This document’s purpose is to communicate conventions for using those symbols and colors to accurately and consistently communicate intended information via graphics-based documentation. These practices are intended for use in service procedures, assembly instructions, training materials, and similar applications when trying to minimize the amount of human natural language text used within the document. The still and animated graphical conventions referenced should support effective communication via paper and “traditional” electronic media. The conventions can also extend to documenting via additional electronic delivery paradigms such as Augmented Reality (AR).

This SAE Standard specifies necessary procedures and control parameters in estimating anisotropic elastic constants of friction material based on pad assembly FRF measurements and optimization. It is intended to provide a set of elastic constants as inputs to brake NVH simulation, with the objective of ensuring pad assembly vibration correlation between simulation and measurements.

This SAE Standard specifies necessary procedures and control parameters in estimating anisotropic elastic constants of friction material based on pad assembly FRF measurements and optimization. It is intended to provide a set of elastic constants as inputs to brake NVH simulation, with the objective of ensuring pad assembly vibration correlation between simulation and measurements.

This SAE Recommended Practice covers power transfer units (PTUs) used in passenger car and sport utility vehicles to support all wheel drive (AWD) operation. PTUs are typically full-time use geared devices (see 3.1). Some PTUs have additional features such as part-time on-demand capability via electronically actuated disconnect features, and other configurations are possible.

The scope of this document focuses on the setup and use of solid particle number (SPN) counting devices in both engine development and certification environments. The document reviews best practices for collecting and measuring samples from both raw and diluted exhaust gas streams across several sample probe insertion locations relative to installed aftertreatment devices. Appropriate dilution techniques, sample transfer processes, and temperature management techniques are included. Finally, performance and validation checks are covered to ensure that long-term degradation and instrument failures can be identified quickly. The particle size range targeted in this document is >23 nm, which aligns with the present EU SPN regulations and targets only solid particles. Current commonly available measurement devices are designed for counting efficiencies of 50% at 23 nm and 90% counting efficiencies at 40 nm so the contents of this document primarily address these particle sizes.

This SAE Information Report provides: a Types of valve guides and their nomenclature b Valve guide alloy designations and their chemistries c Valve guide alloy metallurgy d Typical mechanical and physical properties of guide alloys e Typical dimensional tolerances of valve guides and their counterbores f Recommended interference fits g Installation procedures h Application considerations

This SAE Information Report provides: a Types of valve guides and their nomenclature b Valve guide alloy designations and their chemistries c Valve guide alloy metallurgy d Typical mechanical and physical properties of guide alloys e Typical dimensional tolerances of valve guides and their counterbores f Recommended interference fits g Installation procedures h Application considerations

This report details continuing work examining the fatigue life durability of a US Army Trailer. This report describes, through example, a process to evaluate and reduce the experimental data needed for a Mechanical Systems Physics-of-Failure analysis. In addition the report describes the process used to validate the computer simulation models.

This report details continuing work examining the fatigue life durability of a US Army Trailer. This report describes, through example, a process to evaluate and reduce the experimental data needed for a Mechanical Systems Physics-of-Failure analysis. In addition the report describes the process used to validate the computer simulation models.