Search Results

A PC based interactive program was developed to simulate the unfolding and deploying process of a driver side airbag in the sagittal plane. The airbag was represented by a series of nodes. The maximum allowable stretch was less or equal to one between any two nodes. We assumed that the airbag unfolding was pivoted about folded points. After the completion of the unfolding process the airbag would begin to deploy. During the deploying process, two parameters were used to determine the nodal priority of the inflation. The first parameter was the distance between the instantaneous and final positions of a node. Nodes with longer distances to travel will have to move faster. We also considered the distance between the current nodal position and the gas inlet location. For a node closer to the gas inlet, we assumed that the deploying speed was faster. A graphical procedure was used to calculate the area of the airbag.

This paper examines the neck tension force (Fz) of the BioRid II dummy in the IIHS (Insurance Institute of Highway Safety) rear impact mode. The kinematics of the event is carefully reviewed, followed by a detailed theoretical analysis, paying particular attention to the upper neck tension force. The study reveals that the neck tension should be approximately 450N due to the head inertia force alone. However, some of the tests conducted by IIHS had neck tension forces as high as 1400N. The theory of head hooking and torso downward pulling is postulated in the paper, and various publicly available IIHS rear impact tests are examined against the theory. It is found in the analysis that in many of those tests with high neck tension forces, the locus of the head restraint reaction force travels on the dummy's skull cap, and eventually moves down underneath the skull cap, which causes “hooking” of the head on the stacked-up head restraint foam.

Explicit method is commonly used in crashworthiness analysis due to its capability to solve highly non-linear problems without numerous iterations and convergence problems. However, the time step for explicit methods is limited by the time that the physical wave crosses the element. Therefore, to avoid large amount of CPU time, the explicit method is usually used for non-linear dynamic problems with a short period of simulation duration. For problems under quasi-static loading conditions at pre-crash and post-crash, implicit method could be more efficient than explicit methods because the required computation time is much shorter. Due to the recent advance of crash codes, which allows both implicit and explicit computations to be performed in the same code, crash engineers are able to use explicit computation for crash simulation as well as implicit computation for some of the pre-crash quasi-static loading or post-crash spring back simulations.

There are a wide variety of approaches to model the automotive seat and occupant interaction. This paper traces the studies conducted for simulating the occupant to seat interaction in frontal and/or rear crash events. Starting with an initial MADYMO model, a MADYMO-LS/DYNA coupled model was developed. Subsequently, a full Finite Element Analysis model using LS/DYNA was studied. The main objective of the studies was to improve the accuracy and efficiency of CAE models for predicting the dummy kinematics and structural deformations at the restraint attachment locations in laboratory tests. The occupant and seat interaction was identified as one of the important factors that needed to be accurately simulated. Quasi-static and dynamic component tests were conducted to obtain the foam properties that were input into the model. Foam specimens and the test setup are discussed. Different material models in LS/DYNA were evaluated for simulating automotive seat foam.

This paper describes the development of a simulation methodology to predict body mount functional stiffness. The method provides some improvement over the one previously developed by Cheng and Le. Advantages of this method are 1) user's expertise is not a requirement, 2) elimination of trial-and-error runs for tuning the stiffness characteristics and 3) a predictive tool applicable prior to crash tests. Verification of the method is carried out by comparing the numerical results with those obtained from trial-and-error method and tests. The method leads to promising results in full vehicle crash simulations.

This study identified the mechanical properties of ten cadaveric lumbar spines and two Hybrid III lumbar spines. Eight tests were performed on each specimen: tension, compression, anterior shear, posterior shear, left lateral shear, flexion, extension and left lateral bending. Each test was run at a displacement rate of 100 mm/sec. The maximum displacements were selected to approximate the loading range of a 50 km/h Hybrid III dummy sled test and to be non-destructive to the specimens. Load, linear displacement and angular displacement data were collected. Bending moment was calculated from force data. Each mode of loading demonstrated consistent characteristics. The load-displacement curves of the Hybrid III lumbar spine demonstrated an initial region of high stiffness followed by a region of constant stiffness.

A three-dimensional finite element model of a human neck has been developed in an effort to study the mechanics of cervical spine while subjected to impacts. The neck geometry was obtained from MRI scans of a 50th percentile male volunteer. This model, consisting of the vertebrae from C1 through T1 including the intervertebral discs and posterior elements, was constructed primarily of 8-node brick elements. The vertebrae were modeled using linear elastic-plastic materials, while the intervertebral discs were modeled using linear viscoelastic materials. Sliding interfaces were defined to simulate the motion of synovial facet joints. Anterior and posterior longitudinal ligaments, facet joint capsular ligaments, alar ligaments, transverse ligaments, and anterior and posterior atlanto-occipital membranes were modeled as nonlinear bar elements or as tension-only membrane elements. A previously developed head and brain model was also incorporated.

In a frontal automotive crash, the driver's foot is usually stepping on the brake pedal as an instinctive response to avoid a collision. The tensile force generated in the Achilles tendon produces a compressive preload on the tibia. If there is intrusion of the toe board after the crash, an additional external force is applied to the driver's foot. A series of dynamic impact tests using human cadaveric specimens was conducted to investigate the combined effect of muscle preloading and external force. A constant tendon force was applied to the calcaneus while an external impact force was applied to the forefoot by a rigid pendulum. Preloading the tibia significantly increased the tibial axial force and the combination of these forces resulted in five tibial pylon fractures out of sixteen specimens.

For a body-on-frame (BOF) vehicle, the frame is the major structural subsystem to absorb the impact energy in a frontal vehicle impact. It is also a major contributor to energy absorption in rear impact events as well. Thus, the accuracy of the finite element frame model has significant influence on the quality of the BOF vehicle impact predictability. This study presents the latest development of the frame modeling methodology on the simulation of BOF vehicle impact performance. The development is divided into subsystem (frame sled test) and full system (full vehicle test). This paper presents the first phase, subsystem testing and modeling, of the frame modeling development. Based on the major deformation modes in frontal impact, the frame is cut into several sections and put on the sled to conduct various tests. The success of the sled test highly depends on whether the sled results can replicate the deformation modes in the full vehicle.

This study focuses on the modeling of a frame in a body-on-frame (BOF) vehicle to improve the prediction of vehicle response in crashes. The study is divided into three phases - component (frame material modeling), subsystem (frame sled test) and full system (full vehicle test). In the component level, we investigate the available strain rate data, the performance of various material models in crash codes and the effect of the strain rate in crash simulation. In the subsystem phase, we incorporate the strain rate modeling and expand the scope to include both the forming and the welding effects in the subsystem CAE model to improve the correlation between CAE and test. Finally the improved frame modeling methodology with strain rate, forming and welding effects is adopted in full vehicle model. It is found that the proposed frame modeling methodology is crucial to improve the pulse prediction of a full vehicle in crashes.

The most important tool used in testing methods for evaluating the performance of seat-systems in rear-end impacts is a biofidelic crash test dummy. It has been reported that there are differences in response between two kinds of such dummies, BioRID P3 and Hybrid III, in rear-end impacts at Δ V=9.2 km/h. The objective of this study is to compare the responses of these two types of dummies, at moderate speeds with HYGE sled tests (Δ V=15 km/h, 25 km/h). At Δ V=25 km/h or less, the BioRID and HYIII dummies showed clear differences in their response to a rear-end collision, and the BioRID showed higher biofidelity than the HyIII in this condition.

Regarding THOR-50AM dummy lower extremities (hereafter referred to as ""THOR''and ""THOR-LX'') developed as an assembly of lower extremities for next-generation dummies in frontal impact test, we have conducted a series of tests as follows. HYGE sled tests with a toe-board simulating the impact upon intrusion into the vehicle compartment around the occupant feet, dummy dropping tests with two different postures; one is the upright posture with the knees set straight and another is the posture with the knees bent, in order to apply impact loads and to measure/evaluate the impact response characteristics.

In recent years, several kinds of seat systems that aim to reduce cervical spinal injuries in rear impacts, so called ‘whiplash injuries’, have been released by some car manufacturers and seat suppliers in the world. Meanwhile, several kinds of dummies have been developed to be representatives of occupants under such conditions. One of these is the BioRID II equipped with a realistic spine constructed of multiple vertebrae similar to that of a human. It is regarded as the most biofidelic dummy for low speed rear impact. Using this dummy, some typical ‘whiplash protective’ seat systems currently available were dynamically tested to see their performance on injury reduction. From the results of these tests, the design direction to lessen the injury level more efficiently was determined.

Lower extremity injuries in frontal automotive crashes usually occur with footwell intrusion where both the knee and foot are constrained. In order to identify factors associated with tibial shaft injury, a series of numerical simulations were conducted using a finite element model of the whole human body. These simulations demonstrated that tibial mid-shaft injuries in frontal crashes could be caused by an abrupt change in velocity and a high rate of footwell intrusion.

A nonlinear foam was added to a previously created three-dimensional finite element model of the Hybrid III dummy chest which consisted of six steel ribs, rib damping material, the sternum, a spine box and a pendulum. Two standard calibration pendulum impact tests for a Hybrid III dummy chest were used to validate the new model. An explicit finite element analysis code PAM-CRASH was utilized to simulate the dynamic process. At impact velocities of 6.7 m/s and 4.3 m/s, the force and deflection time history as well as the force-deflection plots showed good agreement between model predictions and calibration data. Peak strains also agreed well with experimental data.

Auto racing has been in vogue from the time automobiles were first built. With the dawn of modern cars came higher engine capacities; the speeds involved in these races and crashes increased as well. However, the advent of passive restraint systems such as the helmet, HANS (Head and Neck Support device), multi-point harness system, roll cage, side and frontal crush zones, racing seats, fire retardant suits, and soft-wall technology, have greatly improved the survivability of the drivers in high-speed racing crashes. Three left lateral crashes from Begeman and Melvin (2002), Case #LAS12, #IND14 and #99TX were used as inputs to the Wayne State Human Body Model (WSHBM) in a simulated racing buck. Twelve simulations with delta-v, six-point harness and shoulder pad as design variables were analyzed for the average maximum principal strain (AMPS) in the aorta. The average AMPS for the high-speed crashes were 0.1551±0.0172 while the average maximum pressure was 110.50±4.25 kPa.

The structural differences between the Thor-NT and Thor-FT dummies, which have been proposed as next-generation dummies for frontal crash tests, were examined and the differences in dynamic response were verified by testing. Tests were performed on a HYGE sled simulating a frontal crash at an impact speed of 56 km/h. The 3-point seatbelt plus air bag combination was adopted as the restraint mechanism. Differences in characteristics of the two dummies in the neck, thorax, and abdomen were found by calibration tests. Test results showed that the variation in shape of the abdominal area of the pelvis generates some disparity in the flexion of the thorax and abdomen.

A comprehensive strategy to investigate the role of the body mounts on the passenger compartment response in a frontal crash event is presented. The activities of the study include quasi-static vehicle crush testing, development of a component-level dynamic body mount test methodology, lumped-mass computer modeling, as well as technical analysis. In addition, a means of investigating the effects the body mounts have on the passenger compartment response during a frontal barrier impact is addressed.

A three-dimensional finite element model of the Hybrid III dummy head-neck complex was created to simulate the Amended Part 572 Head-Neck Pendulum Compliance Test, of the Code of Federal Regulations. The model consisted of a rigid head and five circular aluminum disks joined together by butyl elastomer rubber. Contact surfaces were defined to allow the anterior neck to separate upon an application of extension moments. Two mounting positions, one for flexion and the other one for extension, were used to simulate the head-neck calibration tests. An explicit finite element code PAM-CRASH was utilized to simulate the model dynamic responses. Simulation results were compared to experimental data obtained from First Technology Safety Systems Inc. Model predictions agreed well in both flexion and extension. This model can be used to study the head-neck biomechanics of the existing dummy as well as in the development of new dummies.

Improvements for pedestrian head protection in a car-pedestrian accident have been discussed in several countries. Test methods for evaluating head protection have been proposed, and most are sub-systems using rigid headforms with or without headskin. In those tests, HIC is used as a criterion for head protection. This paper discusses the test conditions and requirements of the headform impact test. The influence of different test conditions and their importance on head impact test requirements, were verified. The primary items cited are as follows: (1) The results of the rigid headform were similar to that of the human cadaver skull in cases without skull fractures. Consequently, the rigid headform can be used for the impactor simulating a condition without skull fracture. (2) In the cases of HIC≤1000, the force-deformation curves of the hoodtops showed similar characteristics with maximum dynamic deformations over 60mm. (3) Impactor mass affected the maximum acceleration and HIC.