Search Results

The Texas Project was a multi-year study of aftermarket conversions of a variety of light-duty vehicles to CNG or LPG. One aspect of this project was to examine the factors that influence the economics of fleet conversions to these alternative fuels. The present analysis did not include longer-term effects (such as possible increases in exhaust system life or increases in tire wear). Additionally, assumptions were required to estimate the costs of repairs to the alternative fuel system and engine. Other factors considered include conversion cost, fuel prices, annual alternative fuel tax (as applied for the state of Texas), annual miles accumulated, and the percent miles traveled while using the alternative fuel for dual fuel conversions.

The Texas Department of Transportation (TxDOT) began using an emulsified diesel fuel as an emissions control measure in July 2002. They initiated a study of the effectiveness of this fuel in comparison to conventional diesel fuel for TxDOT's Houston District operations and included the fleet operated by the Associated General Contractors (AGC) in the Houston area. Cost-effectiveness analyses, including the incremental cost per ton of NOx removed, were performed. NOx removal was the focus of this study because Houston is an ozone nonattainment area, and NOx is believed to be the limiting factor in ozone formation in the Houston area. The cost factors accounted for in the cost-effectiveness analyses included the incremental cost of the fuel (including an available rebate from the State of Texas), the cost of refueling more often, implementation costs, productivity costs, maintenance costs, and various costs associated with the tendency of the emulsion to separate.

The Texas Department of Transportation (TxDOT) began using an emulsified diesel fuel in July 2002. They initiated a simultaneous study of the effectiveness of this fuel in comparison to 2D on-road diesel fuel, which they use in both their on-road and off-road equipment. The study also incorporated analyses for the fleet operated by the Associated General Contractors (AGC) in the Houston area. Some members of AGC use 2D off-road diesel fuel in their equipment. The study included comparisons of fuel economy and emissions for the emulsified fuel relative to the conventional diesel fuels. Cycles that are known to be representative of the typical operations for TxDOT and AGC equipment were required for use in this study. Four test cycles were developed from data logged on equipment during normal service: 1) the TxDOT Telescoping Boom Excavator Cycle, 2) the AGC Wheeled Loader Cycle, 3) the TxDOT Single-Axle Dump Truck Cycle, and 4) the TxDOT Tandem-Axle Dump Truck Cycle.

Cylinder liner rotation (Rotating Liner Engine, RLE) is a new concept for reducing piston assembly friction in the internal combustion engine. The purpose of the RLE is to reduce or eliminate the occurrence of boundary and mixed lubrication friction in the piston assembly (specifically, the rings and skirt). This paper reports the results of experiments to quantify the potential of the RLE. A 2.3 L GM Quad 4 SI engine was converted to single cylinder operation and modified for cylinder liner rotation. To allow examination of the effects of liner rotational speed, the rotating liner is driven by an electric motor. A torque cell in the motor output shaft is used to measure the torque required to rotate the liner. The hot motoring method was used to compare the friction loss between the baseline engine and the rotating liner engine. Additionally, hot motoring tear-down tests were used to measure the contribution of each engine component to the total friction torque.

The Texas Department of Transportation (TxDOT) began using an ultra-low-sulfur, low aromatic, high cetane number diesel fuel (TxLED, Texas Low Emission Diesel) in June 2003. They initiated a simultaneous study of the effectiveness to reduce emissions and influence fuel economy of this fuel in comparison to 2D on-road diesel fuel used in both their on-road and off-road equipment. The study incorporated analyses for the fleet operated by the Association of General Contractors (AGC) in the Houston area. Some members of AGC use 2D off-road diesel in their equipment. One off-road engine, two single-axle dump trucks, and two tandem-axle dump trucks were tested. The equipment tested included newer electronically-controlled diesels. The off-road engine was tested over the TxDOT Telescoping Boom Excavator Cycle. The dump trucks were tested using the “route” technique over the TxDOT Single-Axle Dump Truck Cycle or the TxDOT Tandem-Axle Dump Truck Cycle.

This paper discusses the Formula SAE Student Engineering Design Competition that was held May 27–29, 1982. As was the case of previous student engineering design competitions, the purpose of the Formula SAE Competition is to enhance engineering education by requiring students to apply the technical knowledge gained in their coursework to a practical engineering design problem including choice of appropriate design criteria, design, fabrication, testing, and evaluation. For the Formula SAE Competition, the design problem chosen is to design, construct, and compete a low powered Indianapolis-type race car. The purpose of this paper is to describe the 1982 Formula SAE Competition and to present the results of this event. It is expected that this paper will serve as a guide to hosts of similar competitions and will aid future Formula SAE competitors.

This paper discusses the Formula SAE Student Engineering Design Competition that was held May 24-26, 1984. As was the case of previous student engineering design competitions, the purpose of the Formula SAE Competition is to enhance engineering education by requiring students to apply the technical knowledge gained in their coursework to a practical engineering design problem including choice of appropriate design criteria, design, fabrication, testing, and evaluation. For the Formula SAE Competition, the design problem chosen is to design, construct, and compete a low powered Formula type race car. The purpose of this paper is to describe the 1984 Formula SAE Competition and to present the results of this event. It is expected that this paper will serve as a guide to hosts of similar competitions and will aid future Formula SAE competitors.

This paper discusses the Formula SAE Student Engineering Design Competition that was held May 26-28, 1983. As was the case of previous student engineering design competitions, the purpose of the Formula SAE Competition is to enhance engineering education by requiring students to apply the technical knowledge gained in their coursework to a practical engineering design problem including choice of appropriate design criteria, design, fabrication, testing, and evaluation. For the Formula SAE Competition, the design problem chosen is to design, construct, and compete a low powered Formula type race car. The purpose of this paper is to describe the 1983 Formula SAE Competition and to present the results of this event. It is expected that this paper will serve as a guide to hosts of similar competitions and will aid future Formula SAE competitors.