Search Results

With fuel efficiency becoming an increasingly critical aspect of internal combustion engine (ICE) vehicles, the necessity for research on efficient generation of electric energy has been growing. An energy management (EM) system controls the generation of electric energy using an alternator. This paper presents a strategy for the EM using a control mode switch (CMS) of the alternator for the (ICE) vehicles. This EM recovers the vehicle’s residual kinetic energy to improve the fuel efficiency. The residual kinetic energy occurs when a driver manipulates a vehicle to decelerate. The residual energy is commonly wasted as heat energy of the brake. In such circumstances, the wasted energy can be converted to electric energy by operating an alternator. This conversion can reduce additional fuel consumption. For extended application of the energy conversion, the future duration time of the residual power is exploited. The duration time is derived from the vehicle’s future speed profile.

An efficient development environments such as Software-in-the-Loop Simulation (SILS) and Rapid Control Prototyping (RCP) have been widely used to reduce the development time and cost of real-time ECUs. However, conventional SILS does not consider temporal behaviors caused by computation time, task scheduling, network-induced delays, and so on. As a result, the control performance of ECU is likely to be degraded after implementation. To overcome this problem, SILS/RCP which considers the temporal behaviors was suggested in the previous research. In this study, we validated the proposed SILS/RCP environments which are used to design an Electronic Stability Control (ESC) system which is one of the hard real-time control systems. The proposed SILS/RCP environments make it possible to realize ECUs in the early design phase by considering temporal behaviors.

FlexRay is a deterministic and fault-tolerant in-vehicle network(IVN) protocol. It is expected to become a practical standard for automotive communication systems. According to the FlexRay protocol specifications, there are about 60 configurable parameters which should be determined in the design phases. The parameters increase the complexities of FlexRay-based control system development. In this study, we are suggesting a formal design process for FlexRay-based control systems, which is focused on network parameter optimization. We introduce design phases from functional system models to implementations. These phases present formal ways for task allocation, node assignment, network configuration, and implementations. In the network configuration phase, two FlexRay core parameters are selected to optimize network design. Optimal methods of the core parameters provide concise guide lines for optimal communication cycle length and optimal static slot length.

Controlled Auto-Ignition (CAI) combustion is a new combustion concept. Unlike the conventional internal combustion engine, CAI combustion takes place homogeneously throughout the fuel/air mixture with self ignition, and the mixture is burned without flame propagation. The start of combustion (SOC) is a critical factor in the combustion because SOC affects exhaust gas emissions, engine power, fuel economy and combustion characteristics. This paper presents a control oriented SOC detection method using a 10 bar of difference pressure, and proposes 50 percent normalized difference pressure for SOC detection parameter. Difference pressure is defined as the difference between the in-cylinder firing pressure and the in-cylinder motoring pressure. These methods were determined by CAI combustion experiments. Managing the difference pressure is a fast and precise method for SOC detection.

In this paper, we proposed a formalized design procedure for networked control systems (NCSs). In a conventional development of NCSs, well-designed control algorithms do not result in the intended control performance after an implementation due to time delays, such as network-induced delays and controller computation delays. The proposed design procedure shows how to minimize the degradation of the control performance caused by the time delays. The design procedure was verified by designing a network-based traction control system (TCS). The designed TCS was realized and tested by using a rapid control prototyping (RCP) platform and a hardware-in-the-loop simulation (HILS) environment.

A control method using an in-cylinder pressure sensor can directly and precisely control engine combustion, lowering harmful emissions and fuel consumption levels. However, this method cannot be applied to a conventional engine management system because of its inaccuracy and the high cost of the pressure sensor, as well as the high computational load. In this study, we propose a real-time IMEP estimation method for a common rail direct injection diesel engine using the difference pressure integral as a cylinder pressure variable. The proposed method requires less computational load, enabling the IMEP to be estimated in real-time. In addition, we validated the estimation algorithm through simulation and engine experiments. The IMEP was accurately estimated with a small root mean square error of below 0.2305 bar.

Since many electric and electronic systems are continuously added in a vehicle to meet various regulations and customer demands over the last decade, the demand on the electric power have been substantially increased. Furthermore the idle time fraction during the vehicle traveling has been increased due to the heavy urban traffic condition. The electric power system of the modern vehicle has to supply enough electrical energy to numerous electrical and electronic systems. A detailed understanding of the characteristics of the electric power system, electrical load demands, and driving environment such as road, season, and vehicle weight are required when the capacities of generator and battery are determined for a vehicle. In order to avoid an over or under design problem of the electric power system, a simulation program for electric power estimation is adequate.

A controller is introduced for air-to-fuel ratio management, and the control scheme is based on the feedback error learning method. The controller consists of neural networks with linear feedback controller. The neural networks are radial basis function network (RBFN) that are trained by using the feedback error learning method, and the air-to-fuel ratio is measured from the wide-band oxygen sensor. Because the RBFNs are trained by online manner, the controller has adaptation capability, accordingly do not require the calibration effort. The performance of the controller is examined through experiments in transient operation with the engine-dynamometer.

The development of autonomous vehicle requires the state-of-the-art technologies in perception, planning, control, and system integration. This paper presents an overview of the system architecture and software architecture of autonomous vehicles for system integration. Network based system architecture in this paper provides a distributed computing system for autonomous driving. Further, a real-time path planning and a target speed generation are described based on the curvilinear coordinate system. The design of a path in the curvilinear coordinate system stretches the design space as like the Cartesian coordinate system to simplify the generation of the path. In determination of target speed, curvatures and risk of a generated path were utilized for safe autonomous driving.

The electrical power system is the vital lifeline to most of the control systems on modern vehicles. The demands on the system are highly complex, and a detailed understanding of the system behavior is necessary both to the process of systems integration and to the economic design of a specific control system or actuator. The vehicle electric power system, which consists of two major components: a generator and a battery, has to provide numerous electrical and electronic systems with enough electrical energy. A detailed understanding of the characteristics of the electric power system, electrical load demands, and the driving environment such as road, season, and vehicle weight are required when the capacities of the generator and the battery are to be determined for a vehicle. An easy-to-use and inexpensive simulation program may be needed to avoid the over/under design problem of the electric power system. A vehicle electric power simulator is developed in this study.

In order to evaluate vehicle powertrain performances and driver behaviors, a computer aided in-vehicle data acquisition system named MOde Survey System (MOSS) is newly developed in conjunction with a motor manufacturer. MOSS is designed to be used by personnel related to vehicle emissions and energy with the aim of being cost-effective and easy-to-use. Since driving behaviors and patterns influence powertrain performance in terms of fuel economy and emissions, engineers can utilize the system for understanding the driving pattern and traffic situation quantitatively. MOSS mainly consists of an MCU-based hardware and PC-based software. MOSS logs and analyzes various data related to vehicle driving. Compared to currently-existing Test and Measurement Systems, MOSS is designed and developed for a specific goal with several unique features.

The electric power system of a modern vehicle has to supply enough electrical energy to numerous electrical and electronic systems. The electric power system of a vehicle consists of two major components: a generator and a battery. A detailed understanding of the characteristics of the electric power system, electrical load demands, and the driving environment such as road, season, and vehicle weight are required when the capacities of the generator and the battery are to be determined for a vehicle. In order to avoid the over/under design problem of the electric power system, an easy-to-use and inexpensive simulation program may be needed. In this study, a vehicle electric power simulator is developed. The simulator can be utilized to determine the optimized capacities of generators and batteries appropriately. To improve the flexibility and easy usage of the simulation program, the program is organized in modular structures, and is run on a PC.