Search Results

Gasoline turbocharged direct injection (GTDI) engines, such as EcoBoost™ from Ford, are becoming established as a high value technology solution to improve passenger car and light truck fuel economy. Due to their high specific performance and excellent low-speed torque, improved fuel economy can be realized due to downsizing and downspeeding without sacrificing performance and driveability while meeting the most stringent future emissions standards with an inexpensive three-way catalyst. A logical and synergistic extension of the EcoBoost™ strategy is the use of E85 (approximately 85% ethanol and 15% gasoline) for knock mitigation. Direct injection of E85 is very effective in suppressing knock due to ethanol's high heat of vaporization - which increases the charge cooling benefit of direct injection - and inherently high octane rating. As a result, higher boost levels can be achieved while maintaining optimal combustion phasing giving high thermal efficiency.

Fuel injection is a key process influencing the performance of Gasoline Direct Injection (GDI) Engines. Injecting fuel at elevated temperature can initiate flash boiling which can lead to faster breakup, reduced penetration, and increased spray-cone angle. Thus, it impacts engine efficiency in terms of combustion quality, CO2, NOx and soot emission levels. This research deals with modelling of flash boiling processes occurring in gasoline fuel injectors. The flashing mass transfer rate is modelled by the advanced Hertz-Knudsen model considering the deviation from the thermodynamic-equilibrium conditions. The effect of nucleation-site density and its variation with degree of superheat is studied. The model is validated against benchmark test cases and a substantiated comparison with experiment is achieved.

Internal combustion (IC) engines fueled by hydrogen are among the most efficient means of converting chemical energy to mechanical work. The exhaust has near-zero carbon-based emissions, and the engines can be operated in a manner in which pollutants are minimal. In addition, in automotive applications, hydrogen engines have the potential for efficiencies higher than fuel cells.[1] In addition, hydrogen engines are likely to have a small increase in engine costs compared to conventionally fueled engines. However, there are challenges to using hydrogen in IC engines. In particular, efficient combustion of hydrogen in engines produces nitrogen oxides (NOx) that generally cannot be treated with conventional three-way catalysts. This work presents the results of experiments which consider changes in direct injection hydrogen engine design to improve engine performance, consisting primarily of engine efficiency and NOx emissions.

New emissions certification requirements for medium duty vehicles (MDV) meeting chassis dynamometer regulations in the 8,500 lb to 14,000 lb weight classes as well as heavy duty (HD) engine dynamometer certified applications in both the under 14,000 lb and over 14,000 lb weight classes employing large diameter exhaust pipes (up to 4″) have created new exhaust stream sampling concerns. Current On-Board-Diagnostic (OBD) dyno certified particulate matter (PM) requirements were/are 7x the standard for 2010-2012 applications with a planned phase in down to 3x the standard by 2017. Chassis certified applications undergo a similar reduction down to 1.75x the standard for 2017 model year (MY) applications. Failure detection of a Diesel Particulate Filter (DPF) at these low detection limits facilitates the need for a particulate matter sensor.

This paper describes development challenges for Heavy-Duty (HD) on-highway Diesel Direct Injection (DDI™) engines to meet the extremely advanced US-EPA 2010 (later named US 2010) emission limits while further increasing power density in combination with competitive engine efficiency. It discusses technologies and solutions for lowest engine-out emissions in combination with most competitive fuel consumption values and excellent dynamic behavior. To achieve these challenging targets, base engine hardware requirements are described. In detail the development of EGR systems, especially the challenges of running high EGR rates over the whole engine speed range also at high load, the dynamic EGR control for transient engine operation to achieve lowest NOx emissions at the smoke limit with excellent load response is discussed. Also the effect of the turbo-machinery on power density and transient engine behavior is shown.

Robust on-board diagnosis of emission catalyst performance requires the development of artificially damaged "threshold" catalysts that accurately mimic the performance of damaged catalysts in customer use. The threshold catalysts are used by emissions calibrators to determine fore-aft exhaust oxygen sensor responses that indicate catalyst failure. Rather than rely on traditional trial-and-error processes to generate threshold catalysts, we have used a DFSS (Design For Six-Sigma) approach that explores, at a research level, the relationship between oxygen storage capacity (OSC) of the catalyst (i.e., the fundamental property dictating the response of the aft oxygen sensor) and key process input variables: high-temperature exposure, phosphorus poisoning, and catalyst "recovery."

Exhaust gas temperature is often measured with a device such as thermocouple or RTD (Resistance Temperature Detector). An alternative method to determine the gas temperature would be to use an existing gas sensor heating mechanism to perform as a temperature sensor. A planar type FLOH (Fast Light Off HEGO-Heated Exhausted Gas Oxygen) sensor under transient vehicle speed/load conditions is suited to this function and was modeled to predict the exhaust gas temperature. The numerical input to the model includes exhaust flow rate, heater voltage, and heater current. Laboratory experiments have been performed to produce an equation relating the resistance of the heater and the temperature of the sensor (heater), which provides a method to indirectly determine HEGO sensor temperature.

The requirements to produce high specific power, a high torque across a broad engine speed range and very low emissions levels have been seen as mutually exclusive in a conventional normally aspirated SI engine. Ford Motor Co in association with Cosworth Technology Ltd. have developed a port injection SI engine which achieves in excess of 63kW/ltr, a peak torque in excess of 97Nm/ltr, 92Nm/ltr between 2500rpm and 6500rpm and meets European IV and North American LEV emissions levels for the Focus ST170 in Europe and the SVT Focus in the US. To achieve the required torque across the speed range the volumetric efficiency needed to be maximized at all engine speeds. This was done by fitting continuously variable inlet valve timing, variable length intake manifold and a tuned exhaust manifold. To meet the emissions requirements, the catalyst light off time must be kept to a minimum.

Partial flow sampling methods in emissions testing are interesting and preferred because of their lower cost, smaller size and applicability to engines of all sizes. However the agreement of the results obtained with instruments based on this method to those obtained with the traditional, large tunnel full flow sampling systems needs to be achieved, and the factors of construction that influence this agreement must be understood. These issues have received more attention lately in connection with ISO and WHDC standardization efforts underway to achieve a world-wide harmony in the sampling methods for heavy duty diesel engines, and with the introduction of similar Bag-minidiluter techniques into light duty SULEV gaseous pollutant measurement. This paper presents the theory and practice of a partial flow probe and tunnel design that addresses and minimizes the undesirable effects of the necessary differences between the two sampling methods.

Particulate and manganese mass emissions have been measured as a function of mileage for four Escort and four Explorer vehicles using 1) MMT (Methylcyclopentadienyl Manganese Tricarbonyl) added to the gasoline at 1/32 g Mn/gal and 2) gasoline without MMT. The MMT was used in half of the fleet starting at 5,000 miles. The vehicles were driven on public roads at an average speed of 54 mph to accumulate mileage. This report describes the particulate and manganese emissions, plus emissions of four air toxics at 5,000, 20,000, 55,000, 85,000 and 105,000 miles. Four non-regulated emissions were measured and their average values for vehicles without MMT were 0.6 mg/mi for formaldehyde, 0.7 mg/mi for 1,3-butadiene, 9 mg/mi for benzene and 12 mg/mi for toluene. Corresponding values for MMT-fueled vehicles were between 1.5 and 2.4 times higher.

Emissions sample probes are widely used in engine and vehicle emissions development testing. Tailpipe bag summary data is used for certification, but the time-resolved (or modal) emissions data at various points along the exhaust system is extremely important in the emission control technology development process. Exhaust gas samples need to be collected at various locations along the exhaust aftertreatment system. Typically, a tube with a small diameter is inserted inside the exhaust pipe to avoid any significant effect on flow distribution. The emissions test equipment draws a gas sample from the exhaust stream at a constant volumetric flow rate (typically around 10 SLPM). The sample probe tube delivers exhaust gas from the exhaust pipe to emissions test equipment through multiple holes on the surface of tube. There can be multiple rows of holes at different axial planes along the length of the sample probe as well as multiple holes on a given axial plane of the sample probe.

Automotive three-way catalysts (TWC) were characterized using temperature-programmed reduction (TPR), x-ray diffraction (XRD), Raman spectroscopy, chemisorption measurements and laboratory activity measurements. Capabilities and limitations of these standard analytical techniques for the characterization of production-type automotive catalysts are pointed out. With the exception of chemisorption techniques, all appear to have general utility for analyzing exhaust catalysts. The techniques were used to show that the noble metals and ceria in fresh Pt/Rh and Pd/Rh catalysts are initially highly dispersed and contain a mixture of interacting and non-interacting species. Thermal aging of these catalysts (in the reactor or vehicle) caused both precious metal and ceria particles to sinter, thereby decreasing the interaction between the two.

Recent Federal and California legislation have mandated major improvements in emission control. Tailpipe HC emission must be decreased an order of magnitude for the California Ultra Low Emission Vehicle (ULEV) standard. Present feedback A/F* control systems employ a Heated Exhaust Gas Oxygen sensor (HEGO sensor) upstream of the catalyst to perform A/F feedback control. Limitations on the ultimate accuracy of these switching sensors are well known. To overcome these limitations a linear Universal Exhaust Gas Oxygen sensor (UEGO sensor) placed downstream from the minicatalyst is employed to attain improved A/F control and therefore, higher three-way catalyst (TWC) conversion efficiency. This configuration was granted a patent in 1992 (1**). This study compares performance differences between the two feedback control systems on a Ford Mustang. In initial studies both the UEGO and HEGO sensors were compared at the midposition location downstream of a minicatalyst.

Here we present a latent heat storage device which is used to provide “quick/supplemental” heat to the vehicle's conventional heating system. First, we present data from actual in-vehicle cold weather tests. Data are presented for heater and defroster performance tests, emissions tests and cold start tests after extended soaks. Secondly, heater performance predictions are made using a computer simulation program. Finally, the actual heater performance results are compared with the computer simulation.

Current demands for high fuel efficiency and low emissions in automotive powerplants have drawn attention to the two-stroke engine configuration. The present study measured trapping and scavenging efficiencies of a firing two-stroke spark-ignition engine by in-cylinder gas composition analysis. Intermediate results of the procedure included the trapped air-fuel ratio and residual exhaust gas fraction. Samples, acquired with a fast-acting electromagnetic valve installed in the cylinder head, were taken of the unburned mixture without fuel injection and of the burned gases prior to exhaust port opening, at engine speeds of 1000 to 3000 rpm and at 10 to 100% of full load. A semi-empirical, zero-dimensional scavenging model was developed based on modification of the non-isothermal, perfect-mixing model. Comparison to the experimental data shows good agreement.

In joint partnership with its catalyst suppliers, Ford has made significant advances in the performance of Pd-only three way catalyst (TWC) technology through improvements in catalyst oxygen storage. The following manuscript describes in detail the performance advancement of Ford's Pd-only washcoat technology through the use of laboratory, engine dynamometer, and vehicle emission data.

During the fall of 1992, the Michigan Roadside Study was conducted. During this study IM240 tests were conducted on vehicles that had also been emissions tested during on-road operation via two remote sensors that were separated by 100 feet. The use of two remote sensors provided an indication of the short-term real-world emissions variability of a large number of on-road vehicles. This data was used to determine the frequency of flippers, i.e. vehicles that are sometimes high emitters (>4% CO) and at other times low emitters (<2% CO). The data show that the flipper frequency increases for older model year vehicles. Also, the correlations between remote sensor readings of emissions concentrations and IM240 mass emissions rates were determined. The data show that the correlation between remote sensing and IM240 improves with increasing numbers of remote sensing readings. For three remote sensor readings, CO correlates with an r2 of 0.69 and HC correlates with an r2 of 0.54

Four vehicle fleets, consisting of 3 to 4 vehicles each, were emission tested on a 48″ roll chassis dynamometer using both the FTP urban dynamometer driving cycle and the REP05 driving cycle. The REP05 cycle was developed to test vehicles under high speed and high load conditions not included in the FTP. The vehicle fleets consisted of 1989 light-duty gasoline vehicles, 1992-93 limited production FFV/VFV methanol vehicles, 1992-93 compressed natural gas (CNG) vehicles and their gasoline counterparts, and a 1992 production and two prototype ethanol FFV/VFV vehicles. All vehicles (except the dedicated CNG vehicles) were tested using Auto/Oil AQIRP fuels A and C2. Other fuels used were M85 blended from A and C2, E85 blended from C1, which is similar to C2 but without MTBE, and four CNG fuels representing the range of in-use CNG fuels. In addition to bag measurements, tailpipe exhaust concentration and A/F data were collected once per second throughout every test.

Injecting liquid water into a fuel/air charge is a means to reduce NOx emissions. Such strategies are particularly important to hydrogen internal combustion engines, as engine performance (e.g., maximum load) can be limited by regulatory limits on NOx. Experiments were conducted in this study to quantify the effects of direct injection of water into the combustion chamber of a port-fueled, hydrogen IC engine. The effects of DI water injection on NOx emissions, load, and engine efficiency were determined for a broad range of water injection timing. The amount of water injected was varied, and the results were compared with baseline data where no water injection was used. Water injection was a very effective means to reduce NOx emissions. Direct injection of water into the cylinder reduced NOx emissions by 95% with an 8% fuel consumption penalty, and NOx emissions were reduced by 85% without any fuel consumption penalty.

A simplified method was developed to obtain three-way catalyst performance data to be used for predicting vehicle CVS-H emissions. This method involves engine dynamometer aging of catalysts and characterization of their performance as a function of four variables, namely, redox potential, temperature, space velocity and a modulation parameter. In the process of reducing the number of variables, several simplifications were made. The simplifications, their limitations and the characteristic trends in the performance of a 11 Pt/Rh catalyst are discussed.