Search Results

Controlled Auto-Ignition (CAI) combustion can effectively improve the thermal efficiency of conventional spark ignition (SI) gasoline engines, due to shortened combustion processes caused by multi-point auto-ignition. However, its commercial application is limited by the difficulties in controlling ignition timing and violent heat release process at high loads. Stratified flame ignited (SFI) hybrid combustion, a concept in which rich mixture around spark plug is consumed by flame propagation after spark ignition and the unburned lean mixture closing to cylinder wall auto-ignites in the increasing in-cylinder temperature during flame propagation, was proposed to overcome these challenges.

Due to the rapid development of road infrastructure and vehicle population in China, the fuel consumption and emission of on-road vehicles tested in China World Transient Vehicle Cycle (C-WTVC) cannot indicate the real driving results. But the test results in China Heavy-duty Commercial Vehicle Test Cycle-Coach (CHTC-C) based on the road driving conditions in China are closer to the actual driving data. In this paper, the model for predicting the performance of heavy-duty vehicles is established and validated. The fuel consumption and NOx emission of a Euro VI heavy-duty coach under C-WTVC and CHTC-C tests are calculated by employing the developed model. Furthermore, the fuel consumption of the test coach is optimized and its sensitivity to the driving factors is analyzed.

Lean-burn combustion is an effective method for increasing the thermal efficiency of gasoline engines fueled with stoichiometric fuel-air mixture, but leads to an unacceptable level of high cyclic variability before reaching ultra-low nitrogen oxide (NOx) emissions emitted from conventional gasoline engines. Multi-point micro-flame ignited (MFI) hybrid combustion was proposed to overcome this problem, and can be can be grouped into double-peak type, ramp type and trapezoid type with very low frequency of appearance. This research investigates the micro-flame ignition stages of double-peak type and ramp type MFI combustion captured by high speed photography. The results show that large flame is formed by the fast propagation of multi-point flame occurring in the central zone of the cylinder in the double-peak type. However, the multiple flame sites occur around the cylinder, and then gradually propagate and form a large flame accelerated by the independent small flame in the ramp type.

A high temperature and no oxygen atmosphere fuel reforming has been proposed for the purpose of exergy saving by theoretical analyzing the detailed exergy loss events of combustion process, the correctness and feasibility of this fuel reforming have been verified through experiments. The exergy behaviors of high temperature and no oxygen atmosphere fuel reforming have been extensively studied, and many benefits had been observed including: (1) simplifying the reforming device where catalysts are not necessary; (2) improving the total chemical exergy while effectively converting large moleculae to small moleculae; (3) improving the mixture’s ratio of specific heat that can promote work-extraction; and (4) lengthening the ignition delay that buys time for better mixing process. All of these benefits are conducive to a better organized HCCI combustion that may improve the engine second law efficiency.

Recent toxicological and epidemiologic studies have shown that diesel emissions have been a significant toxic air contaminant. Catalyzed DPF (CDPF) not only significantly reduces the PM mass emissions (>90%), but also further promotes carrier self-regeneration and oxidize more harmful gaseous pollutants by the catalyst coated on the carrier. However, some ultrafine particles and potentially harmful gaseous pollutants, such as VOCs species, originally emitted in the vapor-phase at high plume temperature, may penetrate through the CDPF filter. Furthermore, the components and content of catalyst coated on the CDPF could influence the physicochemical properties and toxicity intensity of those escaping ultrafine particles and gaseous pollutants. In this work, (1) we investigated the influence of precious metal content as a variable parameter on the physicochemical properties and catalytic activities of the small CDPF samples.

To restrain the environmental and energy problems caused by oil consumption and improve fuel economy of heavy-duty commercial vehicles, China started developing relevant standards from 2008. This paper introduces the background and development of China's national standard “Fuel consumption test methods for heavy-duty commercial vehicles”, and mainly describes the test method schemes, driving cycle and weighting factors for calculating average fuel consumption of various vehicle categories. The standard applies to heavy-duty vehicles with the maximum design gross mass greater than 3500 kg, including semi-trailer tractors, common trucks, dump trucks, city buses and common buses. The standard adopts the C-WTVC driving cycle which is adjusted on the basis of the World Transient Vehicle Cycle[1, 2] and specifies weighting factors of urban, rural and motorway segments for different vehicle categories.

To determine the vehicle chassis requirements, wheel force transducer (WFT) have been the best option when it is being used in targeting customer correlation or determining the effective use of the proving ground. However, using wheel force transducer in customer correlation fleet test is often unfeasible due to the huge cost and low practicability. As a result, engineers have to choose other transducer measures. This paper describes an effective approach of wheel force prediction by using the frequency response function (FRF) model of vehicle dynamic system. A vehicle system linear modelling technique is used. For the system identification of FRF, the acceleration and wheel force time history data, as system input and output, are collected from an instrumented passenger car as it traverses in different real-world proving ground surfaces. The obtained FRF represents the complex suspension mechanical model. Once the FRF is calculated, the predicted force signal can be implemented.

In this study, the effect of volatile fractions from engine lubricating oil on diesel particle emissions were studied experimentally. One commercial CF lubricating oil was used and distilled to subtract the different volatile fractions with boiling temperature of 220 °C, 260 °C and 300 °C, respectively. Oils derived from this distillation process were applied as the lubricating oil and following engine experiments were conducted. Diesel primary particles were sampled with a costume designed thermophoretic system. A fast response particulate spectrum equipment was employed to study the size distribution and number concentration of particles in the exhaust. Transmission electron microscopy was used to characterize the size distribution of the primary diesel particles relates to different oil volatile fractions.

The aim of the study was to investigate the difference between car-to-e-bikes and car-to-pedestrian accidents. The China In-depth Accident Study (CIDAS) database was searched from 2011 to 2013 for pedestrians and e-bikes struck by car, van and SUV fronts, which resulted in 104 pedestrian and 85 e-bike cases where information was sufficient for in-depth analysis. Reconstruction by PC-Crash was performed for all of the sampled cases. Pre-crash parameters were calculated by a MATLAB code. Focus was on prototypical accident scenarios and causes; speed as well as possible prevention countermeasures. It has been shown that traffic light violations, road priority violations, and unsure safety (these situations included misjudgments, unpreparedness, proximity to other road users, inappropriate speeds, etc.…) are the main causes in both the VRU groups. Distinctions were found for aspects of car collision speed, accident scenario, distribution of head contact points and so on.

The two-wheeler is a vehicle that runs on two wheels, which is classified as motorcycle, electric-bicycle, and bicycle in this research. China has the largest number of two-wheelers and relevant accidents in the world. The two-wheeler riders have a high level of vulnerability, creating a significant necessity to better understand the characteristics according to the road-user group. The objective of this paper is to study the characteristics and analyze the causes of two-wheeler accidents in China using the CIDAS (China In-Depth Accident Study) Database. 2012 cases of two-wheeler accidents with riders injured or dead were collected from the CIDAS Database from 5 cities (Changchun, Beijing, Weihai, Ningbo and Foshan) in China over a period of 5 years (2011.07-2016.06).

OBD (On-Board Diagnostic) test system is applied to research influences of environmental parameters (altitude and environment temperature) on real-world NOx emission and fuel consumption for heavy-duty diesel trucks in this paper. The research results indicate that altitude and environment temperature have great influence on NOx emission rate and fuel consumption. High altitude in range of 3000~4000 m results in NOx emission rate is lower than low and moderate temperature because of air intake amount decreasing. However the fuel consumption rate is higher than lower altitude because altitude influences real-time changes of air inflow and combustion conditions in the cylinder of the engine. NOx emission rate and fuel consumption is more stable at different vehicle speed, VSP and RPM at high altitude, and NOx emission rate fluctuate dramatically at low and moderate altitude. The fuel consumption rate is higher at 10~20 °C than that at lower and higher temperature.

The aim of this research is to investigate the effects of ashless dispersant of lube oils on diesel exhaust particles. Emphasis is placed on particle size, morphology, nanostructure and graphitization degree. Three kinds of lube oils with different percentages of ashless dispersant were used in a two-cylinder diesel engine. Ashless dispersant (T154), which is widely used in petrochemical industry, were added into baseline oil at different blend percentages (4.0% and 8.0% by weight) to improve lubrication and cleaning performance. A high resolution Transmission Electron Microscope (HRTEM) and a Raman spectroscopy were employed to analyze and compare particle characteristics. According to the experiment results, primary particles diameter ranges from 3 nm to 65 nm, and the diameter distribution conformed to Gaussian distribution. When the ashless dispersant was used, the primary particles diameter decrease obviously at both 1600 rpm and 2200 rpm.

Catalyzed gasoline particulate filter (cGPF) is the prime technology to meet future stringent regulations for particulates from gasoline direct injection (GDI) engines. One of the technical concerns is the ultimate durability of cGPF in regards to engine lubricant formulations. This study investigated two tailored lubricant formulations on catalyzed GPFs which were aged on engine followed by emission testing on vehicle. An engine accelerated aging protocol was developed for cGPFs to simulate thermal aging, ash and soot loading that is at least equivalent to 200,000 km durability requirement. Evaluations include tailpipe emission levels, backpressure, catalytic performance, and post-mortem analysis. Both formulations have demonstrated a high level of cGPF performance retention; performance being assessed in terms of emission level at the end of durability demonstration testing. These formulations provide flexibility in selecting robust lubricant to meet various system requirements.

With the development of vehicle technologies, vehicle safety is much better than before, many companies put research focus on harder accident scenarios. The 25% overlapping collision is considered as one type of most dangerous collision, this paper study this type accidents base on CIDAS database. Paper showed 7 scenarios appeared frequency in China, 11, 12, 1 o’clock are main impact direction. High way and freeway are the main places, and the head, thorax and lower extremities were the main sites of injury.

T-BOX can manage the vehicle’s operation data and position data, and provide the following functions, positioning, vehicle status, motor data, BMS working status, charging status and status alarm, which may effectively promote the development of electric vehicle. Meanwhile, it may bring a series of problems, especially the electromagnetic compatibility (EMC) problems. In this paper, for the exceed standard limits problem of a particular T-BOX sample in radiation emission (RE) and conducted emissions(CE) test process, π filter is designed and added to the positive polar and negative polar of power supply based on the analysis of hardware circuit. The conduction emission test results of T-BOX after optimized can meet the requirements of GB/T 18655-2010 Vehicles, boats and internal combustion engines-Radio disturbance characteristics-Limits and methods of measurement for the protection of on-board receiver standard.

As automobiles are gradually transforming from independent mechanical units to network nodes with intelligent and networked functions, the functions and performance evaluation of intelligent vehicles is facing the new challenges. At present, China has initially classified the level of intelligent vehicles on the basis of SAE, but has not yet formed a scientific, rigorous and comprehensive evaluation system. Therefore, this paper proposes the detailed intelligent evaluation ideas of intelligent vehicles in different levels from 0 to 5 and sets up a "Trinity" evaluation system covering professional evaluation, practical evaluation and market evaluation. Then, with the development progress of intelligent vehicles, we will set up the hierarchical structure of evaluation indicators basing on automated intelligence and connected intelligence.

In this paper, it was researched the degradation characteristics of catalytic performance of three kinds of DPFs (C1, C2 and C3, with precious metal concentrations being 15, 25 and 35 g/ft3 respectively) after diesel truck aging. It is found out that the crystallinity of three kinds of DPF samples (Used) in full vehicle aging was higher than that of fresh samples (Fresh) and aged samples (Aged) in the laboratory. Compared with Fresh samples, the concentration of Pt atom in precious metal on the surface of Aged and Used samples tends to decrease in most cases. Activities to CO and C3H8 of Aged and Used samples of three kinds of DPFs had all been degraded, and activity degradation showed a substantial correlation with concentration reduction rate of precious metal on the carrier surface. NO2 productivity of Used samples all rose. Crystallinity of DPF samples after full vehicle aging in Inlet, Middle and Outlet areas successively increased.

The underbody diffusers are used widely in race cars to improve the flow field structure at the bottom of the car and provide enough downforce. In recent years, passenger cars have begun to use bottom diffuser to improve aerodynamic characteristics, so as to reduce drag and increase downforce. In this paper, the aerodynamic characteristics of the bus with different underbody diffuser angles and channel numbers are studied by numerical simulation analysis. Firstly, the aerodynamics of the bus under different diffuser inlet and outlet angles are studied, and then an optimal inlet and outlet angle is determined based on the simulation results. Then, using this angle as a constant, the 2, 3, and 4 channel numbers were chosen as the diffuser channel variables to study the influence of the multiple-channel diffusers on the aerodynamic drag of the vehicle.

Battery state estimation is one of the most important decision parameters for lithium battery energy management. It plays an important role in improving battery energy utilization, ensuring battery safety and enhancing system reliability. This paper is proposed to provide a dynamic correction of SOC in the full working condition, including static condition and dynamic condition. Based on the Coulomb-counting method, the current SOC value of the battery is calculated. Under the static conditions, the open circuit voltage of the battery is used to directly collect the initial SOC. Under the dynamic working conditions, the open circuit voltage of the battery is estimated by the sliding mode observer. Based on the deviation between the calculated and estimated values of the open circuit voltage, the current coefficient of the Coulomb-counting method is dynamically corrected by PI strategy.

Pure electric vehicles are recognized as one of the most important new energy vehicle types to meet the increasingly stringent standards in energy saving and environment protection. To meet the control demands, China Automotive Technology & Research Center(CATARC) plan to develop an advanced Vehicle Control Platform(VCP) for pure electric vehicles. The developed VCP is well structured on both hardware and software and can be adapted to different pure electric vehicles easily. This paper describes the design of the hardware, the software architecture, the base software and the control strategy applied in the VCP in detail. A matching method is proposed to configure the VCP to a real VCU for the specific application by modifying the hardware channel definition and the control parameters. The paper shows successful application of the VCP on several types of pure electric vehicles.