Search Results

An experiment was performed with a 1.3L catalytic converter design containing a front and rear catalyst each having a volume of 0.65 liters. This investigation varied the front catalyst parameters to study the effects of 1) substrate diameter, 2) substrate cell density, 3) Pd loading and 4) Rh loading on the FTP emissions on three different vehicles. Engine displacement varied from 2.4L to 4.7L. Eight different converters were built defined by a Taguchi L-8 array. Cold flow converter restriction results show the tradeoff in converter restriction between substrate cell density and substrate diameter. Vehicle FTP emissions show how the three vehicles are sensitive to the four parameters investigated. Platinum Group Metals (PGM) prices and Federal Test Procedure (FTP) emissions were used to define the emission value between the substrate properties of diameter and cell density to palladium (Pd) and rhodium (Rh) concentrations.

The National Renewable Energy Laboratory (NREL) collaborated with Millennium Cell and DaimlerChrysler to study heat and water management in a sodium borohydride (NaBH4) storage/processor used to supply hydrogen to a fuel cell in an automotive application. Knowledge of heat and water flows in this system is necessary to maximize the storage concentration of NaBH4, which increases vehicle range. This work helps evaluate the NaBH4 system's potential to meet the FreedomCAR program technical target of 6 wt% hydrogen for hydrogen storage technologies. This paper also illustrates the advantages of integrating the NaBH4 hydrogen processor with the fuel cell.

Electronic Control Units (ECUs) are typically programmed using external programming devices - frequently called Diagnostic Testers. We propose a system and software architecture that requires no Diagnostic Tester for ECU (re)programming. ECU (re)programming is instead managed by an on-board software component, the Flashware-Reprogramming-Controller. It can reside in any ECU that has sufficient memory and processing power as well as good connectivity to internal networks and external sources from which to receive the software to be installed. Appropriate choices could be modern telematic devices. A second co-located on-board software component - the Installation-Configuration-Controller - is used to supervise the installation of new software releases and to validate their integrity after installation. The proposed architecture can be used for software download into ECUs in development, end-of-line production and after sales.

Automakers in the United States have started using bag mini-diluters (BMD) for developing, testing and certifying vehicles, to meet PZEV and SULEV regulation requirements. The BMD system which is a new technology developed by AIGER, is being used as an alternative to the traditional CFV/CVS system for accurate ultra low-level emission measurement. BMD system has shown to have considerable advantage over CFV/CVS system, especially at ULEV/SULEV emission levels. This paper details modifications and diagnostic checks conducted with the existing BMD system at the DaimlerChrysler Tech Center emissions facility, Auburn Hills, Michigan. This paper also discusses possible scenarios where the BMD system at DaimlerChrysler could give erroneous results due to system setup, optimization issues and equipment limitations.

The future of diesel-engine-powered passenger cars and light-duty vehicles in the United States depends on their ability to meet Federal Tier 2 and California LEV2 tailpipe emission standards. The experimental purpose of this work was to examine the potential role of fuels; specifically, to determine the sensitivity of engine-out NOx and particulate matter (PM) to gross changes in fuel formulation. The fuels studied were a market-average California baseline fuel and three advanced low sulfur fuels (<2 ppm). The advanced fuels were a low-sulfur-highly-hydrocracked diesel (LSHC), a neat (100%) Fischer-Tropsch (FT100) and 15% DMM (dimethoxy methane) blended into LSHC (DMM15). The fuels were tested on modern, turbocharged, common-rail, direct-injection diesel engines at DaimlerChrysler, Ford and General Motors. The engines were tested at five speed/load conditions with injection timing set to minimize fuel consumption.

Today the worldwide convergence towards stricter fuel consumption and emission regulations is pushing carmakers and suppliers into new fields of innovation. Valeo Engine Cooling, VEC, is contributing towards these goals by applying its thermal management system expertise in order to reduce fuel consumption and emissions by using an advanced engine cooling system that incorporated variable speed PWM fans, an electric water pump and an electric water control valve. The paper discusses the benefits in terms of engine cooling, fuel economy and emissions over the FTP drive cycle. The paper gives some examples of advanced engine cooling strategies based on a virtual, predictive metal temperature sensor that is used to actuate the electrical water pump at the desired flow rate. The electrical balance between the 42V pump and fans has also been optimized to reduce the vehicle electrical power consumption and to keep the coolant temperature close to 110°C.

Adding oxygenates to diesel fuel has shown the potential for reducing particulate (PM) emissions in the exhaust. The objective of this study was to select the most promising oxygenate compounds as blending components in diesel fuel for advanced engine testing. A fuel matrix was designed to consider the effect of molecular structure and boiling point on the ability of oxygenates to reduce engine-out exhaust emissions from a modern diesel engine. Nine test fuels including a low-sulfur (∼1 ppm), low-aromatic hydrocracked base fuel and 8 oxygenate-base fuel blends were utilized. All oxygenated fuels were formulated to contain 7% wt. of oxygen. A DaimlerChrysler OM611 CIDI engine for light-duty vehicles was controlled with a SwRI Rapid Prototyping Electronic Control System. The base fuel was evaluated in four speed-load modes and oxygenated blends only in one mode. Each operating mode and fuel combination was run in triplicate.

The overall program objectives were three fold: assess the benefits and limitations of oxygenated diesel fuels on engine performance and emissions identify oxygenates most suitable for potential use in future diesel formulations based on physico-chemical properties (e.g. flash point), toxicity, biodegradability and estimated cost of production perform limited emissions and performance testing of the oxygenated diesel blends select at least two oxygenated compounds for advanced engine testing In Part 1 of this program which is described in this paper, an extensive literature review was conducted to identify potential oxygenates for blending into diesel fuels. As many as 71 oxygenates were identified for the initial screening process. Based on a set of physical and chemical properties, a screening methodology was developed to select the 8 oxygenates that will be eligible for engine testing.

Most driver information systems offered in automobiles today display vehicle speed, fluid levels, fluid temperatures, and some basic diagnostic information (warnings, panel lamps). Optional driver information systems add to this list by offering fuel economy information, compass heading, outside temperature and other comfort and convenience related items. Very few provide information in regards to the real performance of the vehicle, its motion in 3-dimensional space, or the driver’s skill and performance. Making this information available to the driver can enhance the “fun-to-drive” aspects of driving.

The development of diesel powered passenger cars is driven by the enhanced emission legislation. To fulfill the future emission limits there is a need for advanced aftertreatment devices. A comprehensive study was carried out focusing on the improvement of the DOC as one part of these systems, concerning high HC/CO conversion rates, low temperature light-off behaviour and high temperature aging stability, respectively. The first part of this study was published in [1]. Further evaluations using a high temperature DPF aging were carried out for the introduced systems. Again the substrate geometry and the catalytic coating were varied. The results from engine as well as vehicle tests show advantages in a highly systematic context by changing either geometrical or chemical factors. These results enable further improvement for the design of the exhaust system to pass the demanding emission legislation for high performance diesel powered passenger cars.

Measuring vehicle exhaust volumetric flow rate accurately and precisely is critical in calculating the correct vehicle modal and bag mini-diluter exhaust emission constituent masses. It is also instrumental in engine calibration practices. Currently, DaimlerChrysler's Emission and Certification Lab in Auburn Hills, Michigan utilizes constant volume sampling bag systems to certify vehicles but the automotive technological trend is heading toward the bag mini-diluter for greater precision at low emission levels. The bag mini-diluters, as well as the modal sampling system, used extensively in vehicle development testing, rely on exhaust flow rate measurement by means of a direct vehicle exhaust flow meter named E-Flow. The E-Flow has few limitations such as flow profile instability at low idle flow rates and reaction to resonating pressure waves in the exhaust system.

As the volume and complexity of electronics increases in automobiles, so does the complexity of the electromagnetic relationship between systems. The reliability and functionality of electronic systems in automobiles can be affected by noise sources such as direct current (DC) motors. A typical automobile has 25 to 100+ DC motors performing different tasks. This paper investigates the noise environment due to DC motors found in automobiles and the requirements that automobile manufacturers impose to suppress RF electromagnetic noise and conducted transients.

Barrier impacts are routinely used to estimate the impact response of vehicles in vehicle-to-vehicle crashes. One area of investigation is the detection of the secondary energy absorbing structures provided for under-/over-ride mitigation as a result of increased structural engagement -- improved geometric compatibility. The flat rigid barrier and the Transportation Research Laboratory’s (TRL) full width honeycomb barrier are commonly considered. In the present study, a vehicle-to-vehicle impact that exhibited no under-/over-ride condition was compared to finite element analysis of vehicle impacts to the two different barriers in order to evaluate their ability to detect the secondary energy absorbing structure. This study demonstrates that the rigid barrier and the TRL barrier yield similar quantitative information with regard to vehicle-to-vehicle crashes.

A Robust Engineering experiment was performed to determine the effects PGM loading and placement on the FTP emissions of a 4 cylinder 2.4L and two 8 cylinder 4.7L vehicles. 1.3L catalytic converters were used containing a front and rear catalyst of equal volume. The experiment is defined by a Taguchi L-8 array. Eight different combinations of catalyst PGM loadings were aged and evaluated. Results show that nmHC and NOx emissions are predominately affected by the PGM loading of the front catalyst. The rear catalyst is insensitive to either Pt or Pd which can be used at low concentrations. Results also compare the benefits of Pd and Rh to reduce emissions. Confirmation runs suggest that significant reductions in PGM cost can be achieved over baseline designs.

The paper presents a comparison between the acceleration pulses of vehicle-to-vehicle crash tests with those of different single-vehicle crash tests. The severity of the full frontal rigid barrier test is compared with that of the vehicle- to-vehicle crash test based on average acceleration and time-to-zero-velocity. Based on this a 30mph full frontal rigid barrier test is found equivalent to a 41mph vehicle-to-vehicle crash. A reduced speed of 22mph for full frontal rigid barrier test is found to represent vehicle-to- vehicle crashes with 50%-100% overlap, with each vehicle travelling at 30mph. The paper also presents a comparison of the acceleration pulses from different crash tests based on the pulse shape and the pulse phase cross-correlation. None of the single-vehicle crash tests have been found to resemble vehicle-to-vehicle crashes in terms of the pulse shape and the pulse phase.

DaimlerChrysler and Mechadyne have undertaken a piece of work to investigate the opportunities for improving the operation of light duty diesel engines using variable valve timing. The very high compression ratios used in this type of engine make it essential to be able to alter the valve open periods to affect exhaust valve opening and intake valve closing, whilst leaving the valve motions largely unchanged around overlap top dead centre to avoid valve to piston contact. This paper presents an overview of the design solution, a description of the simulation model used, performance and economy data predicted by the model and a discussion of other areas of opportunity where improvements may be possible.

Tests were conducted at independent laboratories on a patented ashless additive technology designed generically for Fuel Charter I, II and III diesel fuels as defined by, AAMA (American Automobile Manufacturers Association), ACEA (European Automobile Manufacturers Association), EMA (Engine Manufacturers Association) & JAMA (Japan Automobile Manufacturers Association). The instantaneous effect of these additives in 6 light and 2 heavy duty engines in reducing particle number and particle mass emissions were measured as were mileage accumulation effects. Emission tests confirmed PM reduction of up to 19 % from both light duty vehicles tested under ECE15+EUDC or MVEG cycles and heavy-duty engines tested under the R49 or FiGE cycle. The results also indicated that such reduction had negligible or possibly a beneficial effect on NOx emissions.

Deposits on engine parts, and in particular in combustion chambers of modern engines are causing increasing concern in the automobile industry. Highly sophisticated engine management systems make effects on emissions or performance obvious as outgassing of unburned hydrocarbons or variation of spark advance. Reduced mean heat flux away from the cylinder influences engine thermodynamics. Extreme deposits may cause noise increase by carbon rap. A special form of combustion chamber deposits, well known under the synonym spark plug fouling, is a carbon needle on spark plugs, which can cause the total damage of the catalysts (Japanese Industrial Standard D 1606: Adaptability Test Code of Spark Plug for Automobiles) The Co-ordinating European Council for the development of performance tests for transportation fuels, lubricants, and other fluids (CEC) started the development of a new performance test in 1994.

In a consortium of European industrial partners and research institutes, a combination of industrial development and scientific research was organised. The objective was to improve the catalytic NOx conversion for lean burn cars and heavy-duty trucks, taking into account boundary conditions for the fuel consumption. The project lasted for three years. During this period parallel research was conducted in research areas ranging from basic research based on a theoretical approach to full scale emission system development. NOx storage catalysts became a central part of the project. Catalysts were evaluated with respect to resistance towards sulphur poisoning. It was concluded that very low sulphur fuel is a necessity for efficient use of NOx trap technology. Additionally, attempts were made to develop methods for reactivating poisoned catalysts. Methods for short distance mixing were developed for the addition of reducing agent.

The automobile industry is seeing an increased need for the application of plastics and their derivatives in various forms such as fiber reinforced plastics, in the design and manufacture of various automotive structural components, to reduce weight, cost and improve fuel efficiency. A lot of effort is being directed at the development of structural plastics, to meet specific automotive requirements such as stiffness, safety, strength, durability and environmental standards and recyclability. This paper presents the concept of reinforcing large injection molded fiber reinforced body panels with structural uni-directional fibers (carbon, graphite, kevlar or fiber glass) wound in tension around the body panels by filament winding technique. Structural uni-directional fibers in tension wound around the fiber reinforced plastic inner body panels would place these body panels under compression.