Search Results

Diesel particulate mass emissions and their corresponding size distributions have been investigated on a diesel passenger car at steady state conditions using standard filters and a cascade impactor. These tests have been carried out at two different engine operating conditions (2100 rpm, 2.7 and 13.3 kW, respectively) corresponding to low and high exhaust gas temperatures. Two diesel fuels differing in their sulfur content (150 ppm and 2500 ppm S) have been used for these investigations. The particulate size distribution after diesel oxidation catalyst was found to be affected by the sulfur content of the diesel fuel and by the exhaust gas temperature. Interpretations of these results on a mechanistic basis are given. The diesel particulate emission studies have been extended to dynamic vehicle tests.

SOF and de-NOx catalysts are applied to heavy-duty diesel trucks which are regulated by European 13 mode or Japanese 13 mode cycles. Precious metal free catalysts can reduce SOF at low temperatures without increasing sulfates up to 670C. This catalyst shows little deterioration after 400 hours of high temperature engine aging. 32% PM and 47% SOF reduction is observed under 13 mode tests when the exhaust gas temperature exceeds 700C (ECE-13 mode). This precious metal free catalyst is suitable for diesel trucks, especially trucks with natural aspirating engine whose exhaust gas temperature is very high. De-NOx catalysts with a 300-500C NOx reduction temperature window are applied to the Japanese heavy-duty test cycle (Japan 13 mode). When secondary diesel fuel is added under modes 8 to 12, (secondary fuel addition only when catalyst inlet temperature is more than 300C), 19-25% NOx can be reduced with 2-4% fuel penalty.

Several different possibilities will be described and discussed on the processes of reducing NOx in lean-burn gasoline and diesel engines. In-company studies were conducted on zeolitic catalysts. With lean-burn spark-ignition engines, hydrocarbons in the exhaust gas act as a reducing agent. In stationary conditions at λ = 1.2, NOx conversion rates of approx. 45 % were achieved. With diesel engines, the only promising variant is SCR technology using urea as a reducing agent. The remaining problems are still the low space velocity and the narrow temperature window of the catalyst. The production of reaction products and secondary reactions of urea with other components in the diesel exhaust gas are still unclarified.

The exhaust emissions of two stroke vehicles like motorbikes and scooters contribute to the pollution in urban areas of developing countries in South East Asia and India to a major extent. But also in Japan and selected European countries exhaust gas limitations become effective from 10/1998 and 06/1999 for these vehicles. To control this emissions catalytic aftertreatment by Hot Tubes® and/or monolith type catalysts are applied. Due to the constant rich operation of the two-stroke engines, common design criteria for three-way catalysts fail. Extremely high exhaust gas hydrocarbon concentrations lead to high exotherms during oxidation which increases the exhaust gas temperature to a range between 800 and 900 °C. Furthermore the lack of oxygen limits the CO and HC oxidation under certain engine operation conditions. Therefore, water-gas shift and steam reforming reactions play an important part in catalytic aftertreatment of two-stroke exhausts.

For the measurement of NO and NO2 the CLD-analyzer (chemiluminescense detector) has been used for more than twenty-five years. The disadvantage of the CLD is that NO can be measured only. To obtain total NOX (NO+NO2) the exhaust gas sample has to flow through a catalytic converter, which reduces NO2 to NO. The converter has a efficiency between 90 and 100%. For precise NO and NO2 values it is an advantage to analyze NO and NO2 directly. This paper describes a new UV NOX-analyzer for the simultaneous measurement of NO and NO2. Two different configurations, for high and low concentrations, eg. CVS-bag analysis are presented. The performance of the analyzers is documented in comparison to the UV-RAS analyzer with converter for NOX [1] and the conventional CLD-analyzer. The benefits of the new analyzer compared to analyzers equipped with a converter are given in detailed test results.

The California LEV1 II program will be introduced in the year 2003 and requires a further reduction of the exhaust emissions of passenger cars. The cold start emissions represent the main part of the total emissions of the FTP2-Cycle. Cold start emissions can be efficiently reduced by injecting secondary air (SA) in the exhaust port making compliance with the most stringent standards possible. The thermochemical conditions (mixing rate and temperature of secondary air and exhaust gas, exhaust gas composition, etc) prevailing in the exhaust system are described in this paper. This provides knowledge of the conditions for auto ignition of the mixture within the exhaust manifold. The thus established exothermal reaction (exhaust gas post-combustion) results in a shorter time to light-off temperature of the catalyst. The mechanisms of this combustion are studied at different engine idle conditions.

For substantial reduction of fuel consumption of their vehicle fleet, Volkswagen AG has decided to develop spark-ignition engines with direct fuel injection. To launch this new engine concept with stratified lean operation mode while at the same time meeting the stringent EU IV emission standards, it was necessary to develop a suitable exhaust gas aftertreatment system. This was achieved as part of an intensive co-operation between Volkswagen AG and OMG, formerly dmc2 Degussa Metals Catalysts Cerdec AG. The paper describes the demands for exhaust gas aftertreatment due to lean burn operation. In addition the main development steps of the exhaust gas aftertreatment system for Volkswagen FSI engines and catalyst durability over vehicle lifetime are discussed. Focus is laid on the catalyst system design and coating variations. Volkswagen developed a new closed-loop emission control management system which uses NOx-sensor signals for the first time worldwide.

This paper reports first results of research and development work to achieve Nox reduction under lean diesel exhaust gas conditions by using a special coated, zeolite based monolith catalyst. Much attention is paid to the optimization of the activated zeolite system and the influence of group Ib and VIII elements of the periodic system. A major part of the paper deals with the influence of hydrocarbons, carbon monoxide, sulfur dioxide and water on the activity of the catalyst. Another aspect discussed is the influence of the residence time of the exhaust gas components. The thermal stability and the influence of poisoning elements on the catalyst performance is demonstrated by model gas reactor tests on oven and engine aged samples. Finally, first results on the performance of the catalyst system in a vehicle dynometer test are given.

The NO formation is essentially determined by the flame temperature. In an engine the latter depends on the composition of the fuel and the intake gas. In this study the efficiency of various NO reducing measures is analysed by means of a comparison of measurements and computations for the Most frequent operation point of a 1.9 1 DI Diesel engine. The O2 concentration, which is shown to be the dominant source of influence on the flame temperature and NO formation, is varied using synthetic gas mixtures or by EGR. The molar heat capacity of CO2 and H2O in the recirculated exhaust gas, the intake temperature and the H/C ratio in the fuel are less important for the formation of NO. Measures which reduce the NO formation increase the ignition delay and thereby the fraction of the premixed combustion. The impact of EGR on the combustion process is illustrated by high speed filming.

A recently developed Laser Raman Scattering system was applied to measure the in-cylinder air-fuel ratio and the residual gas content (via the water content) of the charge simultaneously in a firing spark-ignition engine during cold start and warm-up. It is the main objective of this work to elucidate the origin of misfires and the necessity to over-fuel at cool ambient temperatures. It turns out that the overall air-fuel ratio and residual gas content (in particular the residual water content) of the charge appear to be the most important parameters for the occurrence of misfires (without appropriate fuel enrichment), i.e., the engine behaviour from cycle to cycle becomes rather predictable on the basis of these data. An alternative explanation for the necessity to over-fuel is given.

Strategic Materials at Reaction Temperatures (SMART) is an approach used to design washcoat systems for passive 4-way emission control catalysts. Light duty diesel vehicles need to meet the European Motor Vehicle Emissions Group (MVEG) cycle or U. S. Federal test procedure (FTP 75). Emissions that are monitored include hydrocarbon (HC), nitrogen oxides (NOx), carbon monoxide (CO) and total particulate matter (TPM). Low engine-exhaust temperatures (< 200°C during city driving) and high temperatures (> 500-800°C under full load and wide-open throttle) make emission control a formidable task for the catalyst designer Gas phase HC, CO and NOx reactions must be balanced with the removal of the soluble organic fraction for the vehicle to be in compliance with regulations. The SMART approach uses model gases under typical operating conditions in the laboratory to better understand the function of individual washcoat components.

In a joint research project between industrial companies and a number of research institutes, nitrogen oxide conversion in oxygen containing exhaust gas has been investigated according to the following procedure Basic investigations of elementary steps of the chemical reaction Production and prescreening of different catalytic material on laboratory scale Application oriented screening of industrial catalyst material Catalyst testing on a lean bum gasoline engine, passenger car diesel engines (swirl chamber and DI) and on a DI truck engine Although a number of solid body structures show nitrogen oxide reduction by hydrocarbons, only noble metal containing catalysts and transition metal exchanged zeolites gave catalytic efficiencies of industrial relevance. A maximum of 25 % NOx reduction was found in the European driving cycle for passenger cars, about 40 % for truck engines in the respective European test.

Zirconium dioxide (zirconia) is a well-known material often being a major component in the washcoat systems of three-way catalysts (TWC) and diesel oxidation catalysts. One important characteristic of zirconia containing washcoats is an improved aging stability which is required to meet the more and more stringent emission standards. In the last few years the utilization of zirconia became even more important - especially for high sophisticated three-way washcoat systems. This was due to the development of high temperature stable oxygen storage components, containing cerium dioxide (ceria) in combination with different other oxides - one very promising candidate being zirconia. In the present work the results of a research program are discussed, focusing on the influence of zirconia in combination with ceria and additional rare earth promoters on the stability of the oxygen storage characteristics.

A new method for the analysis of the gas flow in an internal combustion engine has been developed. It is based on the interactive coupling between commercially available three (STAR-CD) and one dimensional (PROMO) fluid dynamics codes. With this method the detailed transient flow distribution for any engine component of interest can be calculated taking into account the overall gas dynamic interaction with other engine components. The underlying physics and numerics are outlined. A description of the coupling procedure ensuring proper communication between the two computer codes is given. Also addressed is the averaging procedure adopted at the 3D boundaries, including the influence of the 1D/3D interface placement. A first application of this new method is presented, in which the gas flow in a turbo-charged DI-diesel-engine is simulated.

In this paper the emissions of regulated and unregulated exhaust gas components of a fleet of diesel passenger cars measured at Volkswagen in the eighties are compared with the results of a new investigation on modern direct-injection diesel vehicles. The potential of improved diesel fuels to reduce emissions is also examined. The emissions of regulated exhaust gas components as well as fuel consumption have been reduced significantly in the last years as a result of the systematic further development of conventional swirl chamber engines and exhaust gas after-treatment as well as the introduction of SDI/TDI engines. As was to be expected, this has also had a positive effect on the emissions of unregulated exhaust gas components. It has been possible, for example, to reduce the polycyclic aromatic hydrocarbons adsorbed on diesel particulates by more than 95%.

To support the application and design of exhaust gas aftertreatment systems for gasoline fueled passenger cars based on hydrocarbon adsorber catalysts, a computer model was developed. This model is based on simplified, lumped kinetics for the adsorption and desorption of hydrocarbons and for the oxidation of CO and hydrocarbons. Also included in the model are convective transport of heat and mass in the gas phase, mass and heat transfer to the washcoat layer, and diffusion with reaction in the washcoat layer. The continuity equations for this model with the appropriate boundary conditions were solved for a single channel assuming adiabatic behavior. After validation of the prediction on experimental results, this model was used to perform a simple parametric study on the influence of inlet temperature,CO concentration, washcoat loading, adsorber content, and cell density on the HC emission.