Search Results

In this paper, fatigue tests on a cast aluminum alloy (AS7GU-T64) were performed under different frequencies and humidity levels. Tests conducted under conventional frequency in laboratory air have been compared to tests conducted under ultrasonic frequency in dry air, saturated humidity and in distilled water. It was observed that the highest and lowest fatigue lives correspond to ultrasonic fatigue tests in dry air and in distilled water, respectively. Unlike specimens tested at conventional frequency, all of the specimens tested at ultrasonic frequency presented a large amount of slip facets on the fatigue crack propagation fracture surface.

In an automotive cooling circuit, the wax melting process determines the net and time history of the energy transfer between the engine and its environment. A numerical process that gives insight into the mixing process outside the wax chamber, the wax melting process inside the wax chamber, and the effect on the poppet valve displacement will be advantageous to both the engine and automotive system design. A fully three dimensional, transient, system level simulation of an inlet controlled thermostat inside an automotive cooling circuit is undertaken in this paper. A proprietary CFD algorithm, Simerics-Sys®/PumpLinx®, is used to solve this complex problem. A two-phase model is developed in PumpLinx® to simulate the wax melting process. The hysteresis effect of the wax melting process is also considered in the simulation.

The buildup of deposits in EGR coolers causes significant degradation in heat transfer performance, often on the order of 20-30%. Deposits also increase pressure drop across coolers and thus may degrade engine efficiency under some operating conditions. It is unlikely that EGR cooler deposits can be prevented from forming when soot and HC are present. The presence of cooled surfaces will cause thermophoretic soot deposition and condensation of HC and acids. While this can be affected by engine calibration, it probably cannot be eliminated as long as cooled EGR is required for emission control. It is generally felt that “dry fluffy” soot is less likely to cause major fouling than “heavy wet” soot. An oxidation catalyst in the EGR line can remove HC and has been shown to reduce fouling in some applications. The combination of an oxidation catalyst and a wall-flow filter largely eliminates fouling. Various EGR cooler designs affect details of deposit formation.

Nowadays, capacitive handles are increasing their use in high-end commercial vehicles. This particular handle applies a technology that permits to unlock and even lock the vehicle without a key. As benefit for current life, the customer has the possibility to access and close the vehicles more efficiently and faster, just possessing the key in the pocket or any close compartment that the user is carrying, for example, bag, purse, backpack. Even though, the design of capacitive exterior handle must follow several design strategies to avoid nonfunctional in rainy climate. Water could work as a blocker for the sensor signal captured, special design strategies that must be taken in order to minimize that the liquid could ingress the handle and even be retained on the region that sensor is located.

Transient higher-frequency flow-induced tones are often perceived following air-conditioning (A/C) compressor engagements in automotive refrigerant systems, especially the ones with Thermostatic Expansion Valve (TXV) controlled systems. In this paper, the mechanisms of the acoustic tones induced by turbulent flow and shear-layer-instability in A/C lines are presented. Some of the recommended countermeasures for the attenuation and suppression of these flow-induced transient tones are also discussed.

Climate change initiatives such as carbon dioxide (CO2) inventory reporting, emissions trading, and carbon offsets projects are receiving increased public and corporate attention worldwide. Through early, voluntary actions, Ford Motor Company's manufacturing operations have gained first-hand experience with these emerging policy tools and our global, centralized approach has supported our participation in facility CO2 initiatives in a more cost-effective and operationally-efficient manner. Ford's early action has also developed internal expertise which enables us to share our lessons learned with others beginning to investigate climate change initiatives.

For the application of advanced clean combustion technologies, such as diesel HCCI/LTC, a compressor with high efficiency over a broad operation range is required to supply a high amount of EGR with minimum pumping loss. A compressor with high pitch of vaneless diffuser would substantially improve the flow range of the compressor, but it is at the cost of compressor efficiency, especially at low mass flow area where most of the city driving cycles resides. In present study, an ultra low solidity compressor vane diffuser was numerically investigated. It is well known that the flow leaving the impeller is highly distorted, unsteady and turbulent, especially at relative low mass flow rate and near the shroud side of the compressor. A conventional vaned diffuser with high stagger angle could help to improve the performance of the compressor at low end. However, adding diffuser vane to a compressor typically restricts the flow range at high end.

One of the dominant sources of flow losses in the intake system of internal combustion engines (ICE) with log-style manifolds is the interface between the plenum and primary runner. The present study investigates such losses associated with the dividing flow at the entry to primary runner with geometries representative of those used in ICE. An experimental setup was constructed to measure the flow loss coefficients of T-junctions with all branches of circular cross-section. Experiments were conducted with seven configurations on a steady-flow bench to determine the effects of: (1) interface radius equal to 0, 10, and 20% of the primary runner diameter, (2) plenum to primary runner area ratios of 1, 2.124, and 3.117, and (3) primary runner taper including taper area ratios of 2.124 and 3.117. The last two categories employed 20% interface radii. The total mass flow rate was also varied to investigate the effect of Reynolds number Re on loss coefficients.

Collection of diesel exhaust using the Tapered Element Oscillating Microbalance (TEOM) instrument was investigated as an alternative to the traditional method of filter weighing for particulate matter mass determination. Such an approach, if successful, would eliminate considerable manual labor involved in weighing, as well as the delay of hours or days before final results were known. To avoid known artifacts in the second-by-second mode of operation, the TEOM was used in a phase-by-phase mode and was equilibrated with air of constant temperature and humidity before each measurement. Electrically operated valves were used to automate the equilibration and measurement process. The study also included a comparison between two types of TEOM filter - an older type and a new one designed by the TEOM manufacturer for more uniform flow and less flexing. Best results were obtained with the TEOM using the new filter under no-flow conditions.

The penetration of rainwater through the heating ventilation and air conditioning system, HVAC, of a vehicle directly affects the provision of thermal comfort within the vehicle passenger compartment. The first element of a typical HVAC system, namely the cowl box is considered. The purpose of the airway from the cowl grille openings to the air filter, immediately before the blower, is to ensure proper water separation from the incoming air stream before entry onto the air filter and onwards into the rest of the HVAC system. This is achieved by ensuring standing water within the cowl is quickly drained and that water rain droplets or water flows from the windshield and body are separated from the air stream, hence minimising the effect on the total system volumetric flow rate. An experimental study is conducted to examine the effect of plane baffles on the airflow filed within a rectangular duct. A set of plane baffle plates is placed within the cowl duct.

A wind noise model of a vehicle has been developed using Statistical Energy Analysis (SEA) with measured turbulent pressure data as the source input. Empirical formulas are used to scale the input data for changes in flow and design parameters. Wind tunnel tests have been conducted on a standard and modified vehicle to validate the SEA model and the input scaling. The results show good correlation with both the exterior turbulent pressure levels and the interior sound pressure levels across the audio frequency range.

Engine Mapping is usually performed under nominal conditions which include a humidity level of 8 g/Kg. Customers driving at different humidity conditions (which may range from 1 g/Kg in dry and colder climates and up to 35 g/Kg as in tropical climates) may experience a degraded performance due to the errors in engine torque estimation provided by the ECU. The torque estimation error interacts with many other features that affect drivability, such as the peak performance of the engine, transmission shift quality, etc. This paper extends the investigation in Part-1 by analyzing and quantifying the torque estimation error that may result in certain customer use cases at high humidity conditions, due to the mismatch between calibrated and actual conditions. The analysis is mainly performed for Speed-Density systems (MAP sensor based) but the effect of mass air flow sensor (MAF sensor) based systems is also briefly considered.

Engine Mapping is usually performed under nominal conditions which include a humidity level of 8 g/Kg. Customers driving at different conditions (which may range from 1 g/Kg in colder and dry climates and up to 35 g/Kg as in tropical climates) may experience less-than-optimal engine combustion which results in reduced onroad fuel economy. Humidity has an EGR-equivalent effect, and measuring it will correct the spark timing, mainly at Maximum Brake Torque (MBT) and borderline conditions, and claim back some of those losses. This paper aims at quantifying the small fuel economy benefits associated with on-board humidity measurement for certain customer use cases at high humidity conditions. Dyno data was collected for a Ford 2.3L GTDI engine at three speed load points, and intake air humidity was varied between 20% and 80% relative humidity. The effect of humidity compensation on spark timing, combustion phasing, knock, and consequently on overall engine efficiency was analyzed.

This work presents turbulent premixed combustion modeling in spark ignition engines using G-equation based turbulent combustion model. In present study, a turbulent flame speed expression proposed and validated in recent years by two co-authors of this paper is applied to the combustion simulation of spark ignition engines. This turbulent flame speed expression has no adjustable parameters and its constants are closely tied to the physics of scalar mixing at small scales. Based on this flame speed expression, a minor modification is introduced in this paper considering the fact that the turbulent flame speed changes to laminar flame speed if there is no turbulence. This modified turbulent flame speed expression is implemented into Ford in-house CFD code MESIM (multi-dimensional engine simulation), and is validated extensively.

Plug in hybrid electric vehicles (PHEVs) have gained interest over last decade due to their increased fuel economy and ability to displace some petroleum fuel with electricity from power grid. Given the complexity of this vehicle powertrain, the energy management plays a key role in providing higher fuel economy. The energy management algorithm on PHEVs performs the same task as a hybrid vehicle energy management but it has more freedom in utilizing the battery energy due to the larger battery capacity and ability to be recharged from the power grid. The state of charge (SOC) profile of the battery during the entire driving trip determines the electric energy usage, thus determining overall fuel consumption.

Diesel combustion and emissions formation is largely spray and mixing controlled and hence understanding spray parameters, specifically vaporization, is key to determine the impact of fuel injector operation and nozzle design on combustion and emissions. In this study, an eight-hole common rail piezoelectric injector was tested in an optically accessible constant volume combustion vessel at charge gas conditions typical of full load boosted engine operation. Liquid penetration of the eight sprays was determined via processing of images acquired from Mie back scattering under vaporizing conditions by injecting into a charge gas at elevated temperature with 0% oxygen. Conditions investigated included a charge temperature sweep of 800 to 1300 K and injection pressure sweep of 1034 to 2000 bar at a constant charge density of 34.8 kg/m₃.

In modern automobiles, many new complex features are enabled by software and sensors. When combined with the variability of real-world environments and scenarios, validation of this ever-increasing amount of software becomes complex, costly, and takes a lot of time. This challenges automakers ability to quickly and reliably develop and deploy new features and experiences that their customers want in the marketplace. While traditional validation methods and modern virtual validation environments can cover most new feature testing, it is challenging to cover certain real-world scenarios. These scenarios include variation in weather conditions, roadway environments, driver usage, and complex vehicle interactions. The current approach to covering these scenarios often relies on data collected from long vehicle test trips that try to capture as many of these unique situations as possible. These test trips contribute significantly to the validation cost and time of new features.

Corrosion failures of aluminum air conditioner evaporator cores have been reported in regions where the climate is relatively warm and humid. Microbiologically-influenced corrosion [MIC] has been implicated in these failures. Application of surface-treatment chemicals may inhibit microbiological (bacterial) growth and/or attachment, thereby reducing the potential for MIC. In this study, two laboratory methods were developed to evaluate selected surface-treatment chemicals for their ability to inhibit bacterial growth and reduce bacterial attachment to treated surfaces. Using the developed methods, two controlled-atmosphere brazed aluminum core materials and three surface-treatment chemicals were evaluated. Neither of the untreated core materials was found to inhibit the growth of the bacteria tested.

A number of metallic oxidation catalyst substrates with advanced internal structures have emerged in the past few years. In an aftertreatment application, these structures improve gas mixing by increasing turbulence within the substrate's matrix. Modeling results show these advanced structures, under some operating conditions, can be correlated to reductions in catalyst substrate volume and precious metal 1,2. Three structured metallics were compared to a baseline ceramic substrate in a designed experiment to understand the effect of advanced metallic substrates on diesel oxidation catalyst (DOC) sizing and performance. The results showed that smaller metallic DOCs coated with up to 30% less precious metal (PM) catalyst performed on par or better than the baseline ceramic DOC in terms of hydrocarbon conversion, heat-up, and pressure drop.

The automotive refrigerant systems can occasionally exhibit a transient hoot/whistle type noise under certain operating conditions. High pressure/velocity refrigerant flow through an evaporator core can readily excite the inherent acoustical and/or structural modes, resulting in audible transient tones. This condition if present can be experienced while driving away from a short stop and can last 2 to 10 seconds. The ambient conditions suitable for creating this noise are - moderate/high air-conditioning (A/C) load during days at 85-95° F temperatures with high humidity. Possible noise generating mechanisms have been discussed in earlier publications and our findings during this study indicate that they are excited by the high velocity superheated refrigerant vapor flow through the evaporator core plates. Examples of this transient noise and its spectral characteristics are presented to characterize this refrigerant system induced issue.