Search Results

Modern hybrid technologies, especially mild and micro-hybrids with auto start/stop feature, demand a starter with higher power, better performance and longer life than conventional brush-type starters. In this paper, a new starter design using a brushless motor is proposed. This improves the engine crank performance during autostarts due to lower inertia, higher torque and wider power band capability of the brushless motor, especially at higher speeds. The overall integrated system includes the motor, inverter and controller all packaged in the same form factor of the original starter housing as a “drop-in replacement”. The prototype starter motor is designed to operate at 48V with a peak power of 4kW but can be designed to operate at the standard 12V. This paper will describe in detail the functionalities of the overall system and the simulation and experimental results of the prototype that was tested on a 4-cylinder engine in a production crossover vehicle.

Reliable driveaway from frozen condition is one of the challenging design and control problem for fuel cell applications. Different approaches for warmup from frozen conditions have been developed by OEMs, e.g. low voltage inefficient operation, or use of coolant heaters. However, most methods result in water generation which risk icing and blocking the valves and rendering them nonfunctional till they thaw. One such valve is the anode drain valve which is needed to remove water that crosses over across the membrane to anode side. This work discusses characterization of dynamics of water crossover to anode balance of plant via step response experiments on full scale systems, and development of an online estimator to detect onset of anode water crossover via this online observer. In addition, detection via voltage dip-based feedback is also presented.

Hybrid high voltage battery pack is not only heavy mass but also large in dimension. It interacts with the vehicle through the battery tray. Thus the battery tray is a critical element of the battery pack that interfaces between the battery and the vehicle, including the performances of safety/crash, NVH (modal), and durability. The tray is the largest and strongest structure in the battery pack holding the battery sections and other components including the battery disconnect unit (BDU) and other units that are not negligible in mass. This paper describes the mass optimization work done on one of the hybrid batteries using CAE simulation. This was a multidisciplinary optimization project, in which modal performance and fatigue damage were accessed through CAE analysis at both the battery pack level, and at the vehicle level.

Electric vehicles have a strong potential to reduce a continued dependence on fossil fuels and help the environment by reducing pollution. Despite the desirable advantage, the introduction of electrified vehicles into the market place continues to be a challenge due to cost, safety, and life of the batteries. General Motors continues to bring vehicles to market with varying level of hybrid functionality. Since the introduction of Li-ion batteries by Sony Corporation in 1991 for the consumer market, significant progress has been made over the past 25 years. Due to market pull for consumer electronic products, power and energy densities have significantly increased, while costs have dropped. As a result, Li-ion batteries have become the technology of choice for automotive applications considering space and mass is very critical for the vehicles.

The paper presents the main results of a study on the simulation of energy efficient management of on-board electric and thermal systems for a medium-size passenger vehicle featuring a parallel-hybrid diesel powertrain with a high-voltage belt alternator starter. A set of advanced technologies has been considered on the basis of very aggressive fuel economy targets: base-engine downsizing and friction reduction, combustion optimization, active thermal management, enhanced aftertreatment and downspeeding. Mild-hybridization has also been added with the goal of supporting the downsized/downspeeded engine performance, performing energy recuperation during coasting phases and enabling smooth stop/start and acceleration. The simulation has implemented a dynamic response to the required velocity and manual gear shift profiles in order to reproduce real-driver behavior and has actuated an automatic power split between the Internal Combustion Engine (ICE) and the Electric Machine (EM).

Performance testing and evaluation always plays an important role in the developmental process of a vehicle, which also applies to autonomous vehicles. The complex nature of an autonomous vehicle from architecture to functionality demands even more quality-and-quantity controlled testing and evaluation than ever before. Most of the existing testing methodologies are task-or-scenario based and can only support single or partial functional testing. These approaches may be helpful at the initial stage of autonomous vehicle development. However, as the integrated autonomous system gets mature, these approaches fall short of supporting comprehensive performance evaluation. This paper proposes a novel hierarchical and systematic testing and evaluation approach to bridge the above-mentioned gap.

Hybridization is a mainstream technology for automobiles, and its application is rapidly expanding in other fields. Marine propulsion is one such field that could benefit from electrification of the powertrain. In particular, for boats to sail in enclosed waterways, such as harbors, channels, lagoons, a pure electric mode would be highly desirable. The main challenge to accomplish hybridization is the additional weight of the electric components, in particular the batteries. The goal of this project is to replace a conventional 4-stroke turbocharged Diesel engine with a hybrid powertrain, without any penalty in terms of weight, overall dimensions, fuel efficiency, and pollutant emissions. This can be achieved by developing a new generation of 2-Stroke Diesel engines, and coupling them to a state-of-the art electric system. For the thermal units, two alternative designs without active valve train are considered: opposed piston and loop scavenged engines.

GM has recently developed two types of plug-in electric vehicles. First is an extended range electric vehicle such as the Volt, and the second is a battery electric vehicle such as the Bolt. An overview, of traction inverter and power module used in GM battery electric vehicles, is presented. IGBT power modules are critical components used in traction inverters for driving GM Electrified Vehicles. IGBT power modules are also described in a benchmarking study using key metrics based on horizontal die configuration, layout and vertical thermal stack. Power Module evaluation test set up, procedure and instrumentation used in GM Power Module Lab, Pontiac, Michigan are described. GM Electrification development journey depends on IGBT power module passive test benches; turn on/off energy loss tester, thermal resistance tester, and slow/fast power cycles testers (fast junction temperature change, in seconds, and slow baseplate temperature change, in minutes).

This paper summarizes the development of a wireless message from infrastructure-to-vehicle (I2V) for safety applications based on Dedicated Short-Range Communications (DSRC) under a cooperative agreement between the Crash Avoidance Metrics Partners LLC (CAMP) and the Federal Highway Administration (FHWA). During the development of the Curve Speed Warning (CSW) and Reduced Speed Zone Warning with Lane Closure (RSZW/LC) safety applications [1], the Basic Information Message (BIM) was developed to wirelessly transmit infrastructure-centric information. The Traveler Information Message (TIM) structure, as described in the SAE J2735, provides a mechanism for the infrastructure to issue and display in-vehicle signage of various types of advisory and road sign information. This approach, though effective in communicating traffic advisories, is limited by the type of information that can be broadcast from infrastructures.

The automotive industry is facing many significant challenges that go far beyond the design and manufacturing of automobile products. Connected, autonomous and electric vehicles, smart cities, urbanization and the car sharing economy all present challenges in a fast-changing environment which the automotive industry must adapt to. Cars no longer are just standalone systems, but have become constituent systems (CS) in larger System of Systems (SoS) context. This is reflected in the emergence of several acronyms such as vehicle-to-everything (V2X), vehicle-to-vehicle (V2V), vehicle-to-infrastructure (V2I), and vehicle-to-grid (V2G) expressions. System of Systems are defined systems of interest whose elements (constituent systems) are managerially and operationally independent systems. This interoperating and/or integrated collection of constituent systems usually produce results unachievable by the individual systems alone, for example the use of car batteries as virtual power plants.

General Motors’ 3rd generation eAssist propulsion systems build upon the experience gained from the 2nd generation 115v system and the 1st generation 36v system. Extensive architectural studies were conducted to optimize the new eAssist system to maintain the performance and fuel economy gains of the 2nd generation 115v system while preserving passenger and cargo space, and reducing cost. Three diverse vehicle applications have been brought to production. They include two similar pickup trucks with 5.3 liter V8 engines and 8 speed transmissions, a 4-door passenger car with 2.5 liter 4 cylinder normally aspirated gasoline engine and a 6-speed automatic transmission, and a crossover SUV with a 2.0-liter turbocharged engine and 9 speed transmission. The key electrification components are a new water cooled induction motor/generator (MG), new water cooled power electronics module, and two major variants of 86v lithium ion battery packs.

Mean Value Engine Models (MVEM) represent average behaviour of an engine over one or more thermodynamic cycles and have been designed for automotive control and diagnosis applications. However, most MVEMs are limited to the description of the dynamics of few engine sub-systems. The diagnostic capabilities of a vehicular engine health management (VEHM) system that uses such MVEMs are limited. In this paper, the process of deriving an MVEM for an entire engine system from an instantaneous within-cycle crank-angle model (WCCM) is described. This is expected to be more beneficial for fault diagnosis in VEHMs since such MVEMs in the context of state observers, can be used to detect a broader range of faults and also generate a larger number of fault signatures for better fault detection and isolation (FDI). Extended Kalman Filter (EKF) based estimators are developed that use this MVEM for state estimation.

The performance of a High Voltage (HV) battery in an advanced propulsion application is often highly dependent on the customer controlled climate settings of the vehicle system. Cooling of the battery requires an understanding of the environment in which it is expected to operate. Results from testing on various air-cooled systems will be discussed to portray the interactions of the battery system design and the climate control system design. The following topics (in relation to battery cooling) will be discussed: climate control system temperature settings; climate-control system fan settings; climate control system recirculation mode and outside air mode settings; venting of the battery thermal system exhaust air; and the battery location and mounting.

Euro 7/VII regulations are currently under discussion and are expected to be the last big regulatory step in Europe. From available documentation, it is clear the aim of further regulating the extended conditions of use which are still responsible of high emission events (e. g. cold start or altitude) as well as regulating secondary emissions such as NH3, N2O, CH4, Aldehydes (HCHO). Even if not completely fixed yet, the EU7 limits will be challenging for internal combustion engines and even more for Diesel. Despite a consistent reduction of market share, Diesel engines are expected to remain a significant portion in certain sectors such as Heavy duty (HD) and Light-commercial vehicle (LCV) for some decades. In order to reach the new limits being proposed, besides minimizing engine-out emissions, Diesel powertrain will need an aftertreatment system able to work at very high efficiency right after engine start and in almost every working and environmental condition.

Thermal cabin comfort is the largest consumer of battery energy second only to propulsion in Battery Electric Vehicles (BEV’s). Accurate prediction of thermal comfort in the vehicle cabin with fast turnaround times will allow engineers to study the impact of various thermal comfort technologies and develop energy efficient Heating, Ventilation and Air Conditioning (HVAC) systems. In this study a novel data-driven model based on physics-guided Sparse Identification of Nonlinear Dynamics (SINDy) method was developed to predict Equivalent Homogeneous Temperature (EHT), Mean Radiant Temperature (MRT) and cabin air temperature under transient conditions and drive cycles. EHT is a recognized measure of the total heat loss from the human body that can be used to characterize highly non-uniform thermal environments such as a vehicle cabin. The SINDy model was trained on drive cycle data from Climatic Wind Tunnel (CWT) for a representative Battery Electric Vehicle.

The world is moving towards E-mobility solutions and Battery Electric Vehicles (BEVs) are the main enabler towards it. Li-ion cells are the fundamental building block of any BEVs. There are three common types of Li-ion cell design i.e., cylindrical cells, Prismatic Cells and Pouch cells. Ensuring safety of BEVs are critical to gain customer trust and acceptance over Internal Combustion Engine (ICE) vehicles. EV fire is found to be one of the major concerns related to using higher energy batteries. During a crash event, Post-Crash Electrical Integrity of the BEV is to be ensured and hence primary focus is on mitigation of Li-ion cell internal short circuit. It has been seen in prior published articles that cell internal short circuit can be triggered by physical intrusion of cell. This paper primarily focusses on simulating the mechanical behavior of cylindrical cell under various crush conditions.

Vehicle electrification is driven globally due to the increased concerns on carbon emissions. But the challenges in customer acceptance remains esp. in relation to vehicle costs. Virtual simulations can help in cutting down product development cost and enable faster launch of new vehicles. An early stage system model based design iterations can help in cutting down the product development costs and building more robust products. In the current paper, we develop and analyze a battery pack system model for early phase design. We extend a previously developed system model to include critical physics like sub-component level multiphysics for electrical joint integrity. Also, we demonstrate an integration of 3D FEM & system model for improving the accuracy of joint temperature predictions during charging and/or discharging. A typical High Voltage (HV) battery system comprises of battery modules (Li-ion cells, cooling channels, structural frames, interconnect boards) and HV bus bars.

Hardware-in-the-loop (HiL) simulation is an advanced technique for development and testing of complex real-time embedded systems. This technique has greatly developed in the last decades and has been more and more used in the automotive industry for algorithm and software development, hardware validation, safety validation, and fault investigation activities. Plant simulation model executes in HiL simulator to provide a virtual vehicle that interacts in an open-loop or closed-loop fashion with the embedded system that is under test. Compared to in-vehicle testing, HiL simulation provides benefits of low cost, high availability, high flexibility, repeatability, and test automation capability. HiL simulation reduces the risk caused by control failure, which is especially important for self-driving control system development and testing. The HiL simulation system is more application specific.

As fossil fuels dwindle and more electric vehicles enter the market, there is an opportunity to reevaluate the standard brake system. This paper will discuss and compare the differences in brake system sizing between a non-regenerative braking internal combustion engine vehicle and a dedicated battery electric vehicle with regenerative braking. It will use a model derived from component dynamometer testing and vehicle test data of a mid-size production vehicle. The model will be modified for the mass and regenerative braking capabilities of a battery electric vehicle. The contribution of regenerative braking energy will be analyzed and compared to show its impact on component sizing, thermal sizing, and lining life. The detailed design study will calculate the parameters for caliper, rotor design, actuation, etc., that are optimized for 100% regen enabled vehicles.

Vehicle to Everything (V2X) communication is a prominent solution for active safety collision avoidance and for providing autonomous vehicles Non-Line of Sight (NLOS) capabilities. For safety purposes, it is essential the V2X technology would support communication between all road users, e.g., Vehicles (V2V), pedestrians (V2P) and road infrastructure (V2I). Hence, the efficiency of a V2V communication solution should be evaluated through system level performance. In addition, the examined performance metrics need to reflect safety related properties. Metrics as Packet Reception Ratio (PRR) and transmission latencies, which are commonly used to assess V2X system’s functionality, aren’t enough since reception latencies are overlooked. The latter is crucial in ensuring messages would reach their destination on time to avoid hazardous incidents. The reception cadence may be much lower than this of the transmission due to various phenomenon (e.g. channel congestion).