Search Results

The purpose of this paper is to propose a control method to reduce acceleration shock in motorcycles. Reducing the acceleration shock is very important in improving driveability of motorcycles. Motorcycles equipped with manual transmission have some backlashes in the transmission, with large backlash especially in dog clutch portions. We have figured out that one of the main causes of the acceleration shock is the collision of the dogs at high relative angular velocity during acceleration. Also, our data analysis has revealed that there is a correlation between a peak value of the longitudinal body acceleration and the relative angular velocity at the moment of the dog collision. A simulation was undertaken to verify this phenomenon, and its results have made it clear that we need to decrease the relative angular velocity at the moment of the dog collision so as to reduce the acceleration shock.

The power train system for Utility Vehicles (UVs) or All-Terrain Vehicles (ATVs) mainly consists of a rubber V-belt CVT. The adjustment of the CVT specification requires many steps to realize the shifting operations of the CVT so as to satisfy the acceleration feeling of the driver. In this paper, we report on the simulation technology that predicts the transient behavior during an acceleration of the vehicle equipped with a belt tension clutching CVT, which has both functions of the shift operation and the clutch action. By using the developed simulation technique, it has become possible to adjust the CVT specifications efficiently.

The aim of this study was to clarify the feasibility of applying ion current measurement to detect knock and misfire in lean-burn gas engines. The practical applicability was evaluated by conducting a basic test on a small engine and a test on a large engine. The tests were conducted by advancing the ignition timing to cause knocking, and an evaluation was carried out by comparing the knocking intensity detected by ion current signals and by cylinder pressure signals. By increasing the application voltage and including an amplifier circuit, the weak ion current signals were detected, which indicates that it should be possible to use ion current measurement to detect knock and misfire in lean-burn gas engines.

The Advanced ECS is under development for the purpose of saving fuel, improving safety, and cabin comfort. In FY2006 study, basic components (i.e. MDC, OBNOGS, desiccant units, and CO2 removers) have been improved and their performances evaluated including resistance to environmental condition (i.e. vibration). In addition, the suitable system configuration for a 90-seats aircraft has been considered to evaluate the feasibility of the system. In this paper, we show the results of the evaluated performances based on prototype components, and the analytical study of a revised system configuration.

It is thought that the synthetic gas, including hydrogen and carbon monoxide, has a potential to be an alternative fuel for internal combustion engines, because a heating value of the synthetic gas is higher than one of hydrogen or natural gas. A purpose of this study is to acquire stable auto-ignition and combustion of the synthetic gas which is supposed to be applied into a direct-injection compression ignition engine. In this study, the effects of ambient gas temperatures and oxygen concentrations on auto-ignition characteristics of the synthetic gas with changing percentage of hydrogen (H2) or carbon monoxide (CO) concentrations in the synthetic gas. An electronically-controlled, hydraulically-actuated gas injector was used to control a precise injection timing and period of gaseous fuels, and the experiments were conducted in an optically accessible, constant-volume combustion chamber under simulated quiescent diesel engine conditions.

This paper describes a simulation of the lubricating oil flow in a motorcycle oilpan using a CFD technique in consideration of oil suction and oil return. In the technique, sink boundary and source boundary were used to simulate oil suction and oil return, and a VOF method was used to simulate the free surface of oil. To validate the simulation, a simulation result was compared with experiment results of a prototype motorcycle. As a result, the time of the simulated oil pressure drop in main gallery when the motorcycle decelerated rapidly in a racing circuit was agreed with the measured one. In addition, to demonstrate the applicability of the CFD simulation, a case study of the shape optimization on the baffle plate in the oilpan was shown.

In response to design requirements for lower weight and higher output, the motorcycle engine cylinder block has evolved from a cast cylinder block to an aluminum alloy cylinder block whose bore walls are surface-treated for wear-resistance. Hard-chromium plating, nickel-compound plating, and the like are in wide use as the wear-resistance surface treatment method, but spray technology has recently been attracting attention because of less impact on the environment, superior initial running-in performance and good oil retention. We have been applying a unique spraying method called wire explosion spraying to those models with a special need for wear-resistance surface. In this report we describe our wire explosion spray technology. With the aim of improving the bond strength of the sprayed coat, we studied the effects of the collided particles' form on bond strength in the wire explosion spraying conditions.

This paper describes a numerical analysis method for predicting the brake squeal using the Substructure Synthesis Method. This method is more accurate than the classical method based on the mass-spring system, and simpler than the analysis of all the brake system by FEM. The squeal studied here is focused the one occurring in the low frequency range and its mechanism is due the structural instability of the brake assembly. First, some experiments were carried out in order to grasp the brake squeal phenomenon. These experiments made clear the following items. (1) The low frequency brake squeal occurred at 850Hz. (2) The vibration mode shape had 5 nodes fixed in a space. (3) The brake squeal became maximum at 0.3 - 0.5 (MPa) liquid pressure under the constant temperature condition. (4) The higher the temperature of the pad was, the stronger the brake squeal was under the constant liquid pressure condition.

Motorcycle engines are operated at an extremely broad range of revolutions, from 1000 min-1 to 10000 min-1 or more. Ideally, the natural frequency of each part should never match the engine excitation frequency at any point over that entire range of revolution speeds, but practically, there are times when resonance cannot be avoided because the range is so broad, and therefore the vibration amplitude at resonance must be kept low. For this reason, it is important to grasp not only the resonance frequency but also the vibration amplitude at that point. This may be achieved by two methods, measurement and analysis. The direct measurement of vibration is generally difficult because the motorcycle muffler system has a complex shape and in addition it gets very high temperature when the engine is operating. For this reason, with the aim of being able to predict muffler vibration at the design stage, we carried out a vibration test and FEM (finite element method) analysis.

Since construction machinery manufacturers recommend various brands and types of greases for their machinery, customers would benefit from a standardized grease which can be used in all construction machinery. Furthermore, construction machinery manufacturers have many experiences of field problems caused by commercially available and commonly used EP Lithium greases. Therefore, the Fuels and Lubricants Committee of Japan Construction Mechanization Association (JCMA) has developed a new grease specification called “Japan Construction Mechanization Association Specification (JCMAS) GK,” for construction equipment. The JCMAS GK includes requirements for National Lubrication and Grease Institute (NLGI) No. 1 and No. 2 consistency grades. The JCMAS GK greases have enough lubricating properties for periodical grease fitting of most construction machines, hydraulic excavators, bulldozers and wheel loaders. The JCMAS GK greases are applicable from -20 to +130 degrees Celsius.

In the expansion of composite material application, it is one of the most important subjects in assembly of aircraft structure how drilling of composite/metal stack should be processed in an efficient way. This paper will show the result of development of a drill bit for CFRP/Aluminum-alloy stack by Kawasaki Heavy Industries (KHI) and Sumitomo Electric Hardmetal (SEH). In order to improve workability and economic performance, the drill bit which enables drilling CFRP/Al-alloy stack: at 1 shot; from both directions; without air blow and coolant (just usual vacuuming); was required. A best mix drill bit which has smooth multi angles edge and pointed finishing edge was produced as a result of some trials. Developed drill bit achieved required performance and contributed to large cost reduction, labor hour saving, production speed increase and work environment improvement.

During high engine load, adequate engine cooling is necessary to prevent irregularly highly machine temperatures and spark knock that are issues affecting high power from being achieved. However, excessive cooling during low engine load or cooling locations that do not require cooling relatively exacerbates fuel consumption. Therefore, optimization of the engine cooling system is needed to achieve higher performance of motorcycle engines. First of all, in water-cooled engines, conventional water cooling system adjusts the cooling amount via flow channel switching with a thermostat, which is opened in high water temperature. However, with the bypass channel, water may bypass the radiator but still continues to circulate, thereby leading to loss arising from heat transfer from the cylinders.

In this study, we efficiently predict the vibration response of a design shape at a low computational cost in the early development stage, select design proposals with good characteristics from many proposals devised by the designer at the early stage, and forward them to the next stage to achieve the front-loading of development while increasing product value. The application of participation factor (PF) focusing on the response at a specific part for vibration evaluation of a motorcycle frame is described. To reduce the motorcycle frame vibration, an eigenvalue analysis was performed, and appropriate design change proposals were efficiently selected using partial participation factor (PPF), an index showing the relevance of vibration of specific parts or positions. Using the PPF, we extracted which vibration modes considerably contribute to the vibration response of the part of interest.

In the closed environments such as manned space station, it is necessary to remove contaminant gas to keep a suitable environment. Removal of gaseous contaminants generated from crew, animals, and plants is important function to keep the environment below the allowable level in the Closed Ecology Experiment Facilities (abbreviated as CEEF). CEEF consist of three modules for habitat, animal and plant, the supporting facilities for each module and a plant cultivation facility. CEEF are scheduled to be constructed from 1994 in Aomori Prefecture, northern part of Japan. For designing Trace Contaminant Control Assembly (TCCA) for CEEF, the following six (6) trace contaminants have been selected as major contaminant gas in CEEF; Ammonia (NH3) Methane (CH4) Ethylene (C2H4) Carbon Monoxide (CO) Nitrogen Dioxide (NO2) Sulfur Dioxide (SO2) Ethylene is well-known as an aggressive contaminant to plant growth and maturity.

As a result of our researches into reduction of exhaust emissions for small utility two-stroke engines which are widely used for handheld equipment such as a brush cutter and a hedge trimmer, we here discuss how much exhaust emissions can be reduced with only minor modifications of an engine. For the purpose of reducing emissions, we evaluated the effects of exhaust timing retard and of enleanment of carburetor mixture on mass emissions using the existing 25cc two-stroke engine, which emits high levels of HC and CO, and substantially low levels of NOx. We attained great reduction of HC and CO. The power output, however, dropped and both the plug seat and the exhaust gas temperatures rose, which would detract the practicability of the engine. But we solved the problems by modifying the combustion chamber and the exhaust port shape, keeping the emissions reduced as mentioned above.

The engine noise accounts for a relatively large percentage among the noises generated by a motorcycle. Among the parts of the engine, the cover is important in design as well as a source of the engine noise, being at the end of the vibration transfer path. This paper clarifies that the natural frequency of the cover with a flat surface clearly affects its vibration and noise radiation and that its vibration depends on this surface, by investigation of the effect of surface shape of the cover on its vibration and noise radiation and by a modal analysis of its vibration characteristics. In addition, we confirmed that the calculated value of the radiated noise from the cover agrees well with the measured value.

Hydraulic fluid (HF) specifications for mobile construction equipment called JCMAS HK and HKB have been established by the Fuels and Lubricants Committee of Japan Construction Mechanization Association (JCMA). The specifications are designated by two viscosity categories of single grade and multigrade. Each category has ISO viscosity grade (VG) 32 and 46. The JCMAS HK oils are recommended for use in hydraulic systems designed at pressure up to 34.3MPa(5000psi) and to heat hydraulic fluid up to 100 °C. These oils also provide wear control, friction performance, oxidation and rust protection, seal swell control and filterability performance. Two piston pump test procedures were developed to evaluate lubricating performance of these oils under high pressure conditions. The JACMAS HKB oils are classified as environmentally friendly oils due to the additional requirement for biodegradability.

In order to improve the fuel efficiency and the operating performance of motorcycles, there is a need to reduce their weight. Magnesium, which is the lightest of the various metals currently being used and has a high specific strength, has the potential to satisfy that need. We conducted a study to clarify the weldability and strength characteristics of, and the most suitable surface treatment for, extruded magnesium alloys and rolled magnesium alloys. Based on the stress analysis by the finite element method, we designed a magnesium swing arm and produced the prototype swing arm by pressing hot rolled AZ31 magnesium alloy plates and welding them. The prototype is about 10% lighter and has higher torsional rigidity than a conventional aluminum swing arm.

Abnormal combustion, which is a cause for engine failure, is explicated to be high speed knocking by multi-cycle analysis of the cylinder pressure data of snowmobile two stroke cycle engines operated at high speed and wide open throttle condition. A mini-computer was used for the analysis of the cylinder pressure data. Calculation of the entire cycle was conducted until an engine actually failed and the relationship between the engine failure and the conditions surrounding the knocking was made clear. Using the rate of pressure change as a quantitative evaluation method for high speed knocking, a combustion chamber shape with less knocking occurrence possibility was selected.

A new 0.9-liter 4-valve-per-cylinder liquid cooled engine was developed for 1984 model motorcycles. This new engine was optimized from the standpoint of performance, durability, and weight efficiency. Semi-Flat slide carburetors, high compression ratio, relatively short stroke and large valves were employed. This engine was upgraded every other year with changes in displacement. Induction system, exhaust system, and valve train. This paper describes, from the viewpoint of the designer, the evolution of the 4-valve liquid-cooled engine from the 1984 to 1988 models. In that evolutionary process we employed: (1) semi-down draft carburetors with smooth air ducts, (2) a computer-aided intake and exhaust port design and manufacturing system. (3) individual rocker arms. (4) a cool air intake system. (5) lightweight pistons. (6) angle -controlled tightening of connecting rod bolts.