Search Results

A unique differential assembly was needed for the Lawrence Technological University (LTU) SAE Formula race car. Specifically, a differential was required that had torque sensing capabilities, perfect reliability, high strength, light weight, the ability to withstand inertia and shock loading, a small package, no leaks, the ability to support numerous components. In that regard, an existing differential was selected that had the torque sensing capabilities, but had deficiencies that needed to be fixed. Those deficiencies included the following: Differential unit was over 4 kg unmounted, with no housing. This was considered too heavy, when housed properly. Bearing surface was provided on only one end of the carrier. This design provides insufficient bearing surface to support either the differential housing or half-shafts The internal drive splines integral to the case are not optimized for a perpendicular drive/axle arrangement, such as, a chain drive.

All-wheel drive (AWD) vehicle performance considerably depends not only on total power amount needed for the vehicle motion in the given road/off-road conditions but also on the total power distribution among the drive wheels. In turn, this distribution is largely determined by the driveline system and its mechanisms installed in power dividing units. They are interwheel, interaxle reduction gears, and transfer cases. The paper presents analytical methods to evaluate the energy and, accordingly, fuel efficiency of vehicles with any arbitrary number of the drive wheels. The methods are based on vehicle power balance equations analysis and give formulas that functionally link the wheel circumferential forces with slip coefficients and other forces acting onto an AWD vehicle. The proposed methods take into consideration operational modes of vehicles that are tractive mode, load transportation, or a combination of both.

The 2000 Formula SAE Team at Lawrence Technological University (LTU) has designed a chain driven, three-piece aluminum differential unique from past years. This innovative design introduces an adjustable chain mount replacing conventional shackles. Made completely of aluminum, this device moves the entire rear drive train. The gear set remains to be limited slip with a student designed housing. The idea of an aluminum housing with manufactured gear set is a continued project at LTU. After cutting approximately 33% from the weight of the 1999 differential, the 2000 is geared toward a simpler, and smaller design, easier assembly and lighter weight. After reading this brief overview, the idea of this paper is to provide an understanding of the reasoning behind the choices made on the LTU driveline team. FIGURE 1

This paper reviews how sound transmission loss (STL) of insulators is affected by gravitational and thermal effects. A special STL test fixture was designed and fabricated to quickly and accurately obtain the STL measurement of a sample oriented at various controlled angles. The STL apparatus was designed to roll into a large reverberation chamber and act as the anechoic termination for a two-microphone approach to measuring STL. The fixture was also built with the intention of studying the temperature effects on a material's STL performance. A variety of samples, including lightweight and traditional barrier decoupled insulators, were tested in the horizontal, vertical, and inverted positions to evaluate gravitational/inertial effects. Thermal effects were investigated by bringing the STL apparatus and sample to a low temperature by moving outdoors, and then rolling the system into the reverberation chamber, at normal room temperature.

To evaluate traction and velocity performance and other operational properties of a vehicle requires data on some tire parameters including the effective rolling radius in the driven mode (no torque on a wheel), the effective radii in the drive mode (torque applied to the wheel), and also the tire longitudinal elasticity. When one evaluates vehicle performance, these parameters are extremely important for linking kinematic parameters (linear velocity and tire slip coefficient) with dynamic parameters (torque and traction net force) of a tired wheel. This paper presents an experimental method to determine the above tire parameters in laboratory facilities. The facilities include Lawrence Technological University's 4x4 vehicle dynamometer with individual control of each of the four wheels, Kistler RoaDyn® wheel force sensors that can measure three forces and three moments on a wheel, and a modern data acquisition system. The experimental data are also presented in the paper.

Traction control is an electronic means of reducing the wheel spin caused by the application of excessive power for the valuable grip. Wheel spin can result in loss control of the car, reduce acceleration and cause tire wear. In the front wheel tire the loss grip is experienced as underwater, where the front of the car ‘pushes’ forward, not turning as much as the driver has exposed by turning the tearing. In the rear wheels slip causing oversteer, where the rear of the car swings around, turning much sharper than the driver anticipated. The result of all these problems is that the driver starts loosing control of the vehicle, which is undesirable. With the new design of the Traction Control System, the amount of the wheel slippage is precisely controlled. In racing, this means corner can be taken constantly quicker, with system applying the maximum power possible while the driver remains in total control.

Thermal management systems (TMS) of armored ground vehicle designs are often incapable of sustained heat rejection during high tractive effort conditions and ambient conditions. During these conditions, which mainly consist of high torque low speed operations, gear oil temperatures can rise over the allowable 275°F limit in less than twenty minutes. This work outlines an approach to temporarily store excess heat generated by the differential during high tractive effort situations through the use of a passive Phase Change Material (PCM) retrofit thereby extending the operating time, reducing temperature transients, and limiting overheating. A numerical heat transfer model has been developed based on a conceptual vehicle differential TMS. The model predicts the differential fluid temperature response with and without a PCM retrofit. The developed model captures the physics of the phase change processes to predict the transient heat absorption and rejection processes.

The American Axle & Manufacturing Inc. driveline dynamometer provides immense value for experimental validation of product NVH performances. It has been intensively used to evaluate product design robustness in terms of build variations, mileage accumulation, and temperature sensitivity. The current driveline dynamometer input motor system has multiple torsional modes which create strong coupling with test part gear mesh dynamics. Mechanical Engineering seniors at Lawrence Technological University designed, fabricated, and validated a mechanism to decouple the driveline dynamics from the driveline dynamometer dynamics. The student-designed decoupler mechanism is presented with experimental validation of effectiveness in decoupling driveline dynamometer dynamics from the driveline under test.

A steady state vehicle model is developed that will predict engine and automatic transmission operating conditions based on various vehicle configurations and operating conditions. The model provides a better understanding of the effects, including direction and magnitude, of changes in vehicle configuration and/or operating conditions on powertrain requirements. The model results can then be used as input into powertrain matching decisions. In general, the model will begin by determining vehicle road load requirements (wheel speed and torque) as a function of vehicle speed based on ambient, road, and vehicle inputs. Such road load requirement will then be cascaded into input and output requirements of the rear axle, transmission gearing, torque converter (locked and unlocked), and finally the engine. Wide open throttle engine torque data will also be translated into tractive effort at the wheels and resulting acceleration capability versus the vehicle road load requirements.

Online road profiling capability is required for automotive active suspension systems to be realized in a commercial landscape. The challenges that impede the realization of these systems include a profiler’s ability to maintain an optimal resolution of the oncoming road profile (spatial frequency). Shifting of the profile measurement frame of reference due to body motion disturbances experienced by the vehicle also negatively impacts profiling capability. This work details the early development of a corrective look-ahead road profiling system (CLARPS) and its control logic. The CLARPS components are introduced and additional focus will be given to the development of the angle generating function (AGF) and how it drives the ability of the system to optimize look-ahead viewing angles for the best spatial frequency resolution of a road profile. The CLARPS simulation environment is demonstrated with numerical comparison of simulated road profiles at varying vehicle speeds.