Search Results

The world is firmly focused on reducing energy consumption and on increasingly stringent regulations on CO2 emissions. Examples of regulatory changes include the new United States Environmental Protection Agency's (U.S. EPA) fuel economy test procedures which were required beginning with the 2008 model year for vehicles sold in the US market. These test procedures include testing at higher speeds, more aggressive acceleration and deceleration, and hot-weather and cold-temperature testing. These revised procedures are intended to provide an estimate that more accurately reflects what consumers will experience under real world driving conditions. The U.S.

Phosphorus is known to reduce effectiveness of the three-way catalysts (TWC) commonly used by automotive OEMs. This phenomenon is referred to as catalyst deactivation. The process occurs as zinc dialkyldithiophosphate (ZDDP) decomposes in an engine creating many phosphorus species, which eventually interact with the active sites of exhaust catalysts. This phosphorous comes from both oil consumption and volatilization. Novel low-volatility ZDDP is designed in such a way that the amounts of volatile phosphorus species are significantly reduced while their antiwear and antioxidant performances are maintained. A recent field trial conducted in New York City taxi cabs provided two sets of “aged” catalysts that had been exposed to GF-4-type formulations. The trial compared fluids formulated with conventional and low-volatility ZDDPs. Results of field test examination were reported in an earlier paper (1).

Global original equipment manufacturers (OEMs) have requested lower viscosity automatic transmission fluid (ATF) for use in conventional and 6-speed automatic transmissions (AT) to meet growing demands for improved fuel economy. While lower-viscosity ATF may provide better fuel economy by reducing churning losses, other key performance attributes must be considered when formulating lower viscosity ATF(1,2). Gear and bearing performance can be key concerns with lower-viscosity ATFs due to reduced film thickness at the surfaces. Long-term anti-shudder performance is also needed to enable the aggressive use of controlled slip torque converter clutches that permit better fuel economy. And, friction characteristics need to be improved for higher clutch holding capacity and good clutch engagement performance. This paper covers the development of next-generation, low-viscosity ATF technology, which provides optimum fuel economy along with wear and friction durability.

A 100-hour engine dynamometer test for intake valve deposits (IVD) which uses a Ford 2.3L engine was developed by the Coordinating Research Council (CRC). Recently, this test has been approved by the American Society for Testing and Materials (ASTM) as Test Method D 6201-97. Since this test offers improvements in test variability, duration, and cost, it is expected to replace ASTM D 5500-94, a 16,000-km vehicle test run using a BMW 318i, as the key performance test for the Certification of Gasoline Deposit Control Additives by the EPA Final Rule. As a step in the replacement process, a correlation between valve deposit levels for the CRC 2.3L Ford IVD test and ASTM D 5500 BMW IVD test must be determined. This paper provides a statistical review of available data in an attempt to provide such a correlation.

Wet clutch friction devices are the primary means by which torque is transmitted through many of today's modern vehicle drivelines. These devices are used in automatic transmissions, torque vectoring devices, active on-demand vehicle stability systems and torque biasing differentials. As discussed in a previous SAE paper ( 2006-01-3271 - Next Generation Torque Control Fluid Technology, Part II: Split-Mu Screen Test Development) a testing tool was developed to correlate to full-vehicle split-mu testing for limited slip differential applications using a low speed SAE #2 friction test rig. The SAE #2 Split-Mu Simulation is a full clutch pack component level friction test. The purpose of this test is to allow optimization of the friction material-lubricant hardware system in order to deliver consistent friction performance over the life of the vehicle.

Wet clutch friction devices are the primary means by which torque is transmitted in many of today's modern vehicle drivelines. These devices are used in automatic transmissions, torque vectoring devices, active on-demand vehicle stability systems, and torque biasing differentials. As discussed in a previous SAE paper ( 2006-01-3270 - Next Generation Torque Control Fluid Technology, Part I: Break-Away Friction Slip Screen Test Development), a testing tool was developed to simulate a limited slip differential break-away event using a Full Scale-Low Velocity Friction Apparatus (FS-LVFA). The purpose of this test was to investigate the fundamental interactions between lubricants and friction materials. The original break-away friction screen test, which used actual vehicle clutch plates and a single friction surface, proved a useful tool in screening new friction modifier technology.

This paper describes the development of an extended vane pump test procedure utilizing the Eaton® 35VQ-25 vane pump. Evaluation of two commercial Zinc Dithiophosphate containing and two commercial non Zinc (ashless) hydraulic fluids are also described. Results show that extending the test time allows differentiation among fluids which give comparable performance in the standard 50 hour test. System cleanliness, as well as pump weight loss, must be used in the performance assessment.

Light trucks and sport utility vehicles (SUVs) have become extremely popular in the United States in recent years, but this shift to larger passenger vehicles has placed new demands upon the gear lubricant. The key challenge facing vehicle manufacturers in North America is meeting government-mandated fuel economy requirements while maintaining durability. Gear oils must provide long-term durability and operating temperature control in order to increase equipment life under severe conditions while maintaining fuel efficiency. This paper describes the development of a full-scale light duty axle test that simulates a variety of different driving conditions that can be used to measure temperature reduction properties of gear oil formulations. The work presented here outlines a test methodology that allows gear oil formulations to be compared with each other while accounting for axle changes due to wear and conditioning during testing.

In a step-ratio automatic transmission system, wet friction components are widely utilized to alter planetary gear configurations for automatic shifting. Thus, their engagement characteristics have a direct impact on shift quality or drivetrain NVH. A vehicle design process can benefit from predictive friction component models that allow analytical shift quality evaluation, leading to reduced development time. However, their practical application to shift analysis is seldom discussed in the literature although there are many references available for friction component modeling itself. A successful shift analysis requires a balance of model complexity, predictability and computational efficiency for a given objective. This paper reviews three types of friction component models found in today's open literature, namely, first principle based, algebraic, and empirical models. Model structure, assumptions, computational efficiency, and utilities are discussed.

City transit buses are a severe environment for an automatic transmission fluid. The fluid must endure very high operating temperatures because of the use of brake retarders, frequent stop-and-go driving, and numerous shifts. There is an increasing trend toward the use of extended-drain, synthetic-based ATFs for such severe service applications. This paper documents a field trial with both synthetic and petroleum-based ATFs at a large municipal bus fleet in Southern California. Three different commercial ATFs, made with either API Group 2, 3, or 4 base oils, respectively, were compared after roughly 80,000 km. and one year of operation. Because of different additive packages in each fluid, not all of the results can be explained by base oil effects alone. However, the base oil is certainly a dominant contributor to the finished fluid performance. The following four variables were monitored by used oil analysis: iron wear, copper wear, viscosity change, and acid number change.

The popularity of SUVs and light trucks in North America, combined with the return to rear-wheel-drive cars globally, is significantly increasing the installation of torque control devices that improve vehicle stability and drivability. As with other driveline hardware, it is important to optimize the friction material-lubricant-hardware system to ensure that a torque control device provides consistent performance over the life of the vehicle. While there are many publications on friction tests relevant to automatic transmission fluids, the literature relating to torque control testing is not as well developed. In this paper, we will describe a split-mu vehicle test and the development of a split-mu screening test. The screening test uses the SAE#2 friction test rig and shows how results from this test align with those from actual vehicle testing.

The popularity of SUVs and light trucks in North America, combined with the return to rear-wheel-drive cars globally, is significantly increasing the installation rates of torque control devices that improve vehicle stability and drivability. As with other driveline hardware, it is important to optimize the friction material-lubricant-hardware system in order to ensure that a torque control device provides consistent performance over the life of the vehicle. While there are many publications on friction tests relevant to automatic transmission fluids, the literature relating to torque control testing is not as well developed. In this paper we will describe the development of a break-away friction screening test using a Full-Scale Low-Velocity Friction Apparatus (FS-LVFA). Additionally, we will illustrate how this screening test can be used to investigate the fundamental friction material-lubricant interactions that occur in continuously engaged limited slip differentials.

The Coordinating European Council, CEC, develops performance tests for the motor, oil, petroleum, additive and allied industries. In recent years, CEC has moved away from using round robin programmes (RRP's) for monitoring the precision and severity of test methods in favour of regular referencing within a test monitoring system (TMS). In a TMS, a reference sample of known performance, determined by cross-laboratory testing, is tested at regular intervals at each laboratory. The results are plotted on control charts and determine whether the installation is and continues to be fit to evaluate products. Results from all laboratories are collated and combined to monitor the general health of the test. The TMS approach offers considerable benefits in terms of detecting test problems and improving test quality. However, the effort required in collating data for statistical analysis is much greater, and there are technical difficulties in determining precision from TMS data.

The popularity of light trucks and sport utility vehicles (SUVs), coupled with growing consumer demand for vehicles with more size, weight and horsepower, has challenged the original equipment manufacturers' (OEM) ability to meet the Corporate Average Fuel Economy (CAFE) specifications due to the increased contribution of these vehicle classes on fleet averages. The need for improved fuel economy is also a global issue due to the relationship of reduced fuel consumption to reduced CO2 emissions. Vehicle manufacturers are challenged to match the proper fluid with the application to provide the required durability protection while maximizing fuel efficiency. Recent new viscosity classifications outlined under SAE J306 aid in more tightly defining options for lubricant choice for a given application. Changes to the SAE J306 viscosity classification define new intermediate viscosity grades, SAE 110 and SAE 190.

The constant velocity joint (CVJ) has seen increased usage driven by the growth of front wheel drive vehicles over the last 30 years. The CVJ provides a smooth, dynamic connection between the output of the axle or gearbox and the driving wheels of the vehicle. The seemingly simple device, however, requires specially designed greases to maximize protection of the internal components from distress and provide optimum performance and service life. One measure of potential distress in the CVJ can be related to temperature rise which is a reflection of the friction and wear properties of the grease employed. A test rig was designed and a method created to evaluate the temperature response of different greases used in a CVJ. The test rig was designed to allow a wide range of speeds, torques and shaft angles to be used. The rig uses a unique temperature pickup system to allow for dynamic measurement of the grease temperature in the boot.

This paper features the results of emission tests conducted on diesel oxidation catalysts, and the combination of diesel oxidation catalysts and water blend fuel (diesel fuel continuous emulsion). Vehicle chassis emission tests were conducted using an urban bus. The paper reviews the impact and potential benefits of combining catalyst and water blend diesel fuel technologies to reduce exhaust emissions from diesel engines.

This paper outlines the history and background of the NLGI (formerly known as the National Lubricating Grease Institute) lubricating grease specifications, GC-LB classification of Automotive Service Greases as well as details on the development of new requirements for their High-Performance Multiuse (HPM) grease certification program. The performance of commercial lubricating grease formulations through NLGI's Certification Mark using the GC-LB Classification system and the recently introduced HPM grease certification program will be discussed. These certification programs have provided an internationally recognized specification for lubricating grease and automotive manufacturers, users and consumers since 1989. Although originally conceived as a specification for greases for the re-lubrication of automotive chassis and wheel bearings, GC-LB is today recognized as a mark of quality for a variety of different applications.

New technologies are being commercialized across the automotive industry to address demands for improved fuel economy, emissions reductions, and improved customer satisfaction. Push-belt continuously variable transmissions (b-CVTs) are beginning to command a significant percentage of the market now dominated by manual and conventional automatic transmissions. In addition, automobile manufacturers plan to introduce the first traction drive toroidal-CVTs to the market place within the next five years. A review of the relative benefits and limitations of each of these automatic transmissions exists in the literature. In this paper we consider how the performance requirements of each of these automatic transmission systems impact automatic transmission fluid technology. The physical characteristics and screen test performance of two commercial ATFs, a b-CVTF, and two traction fluids were examined.