Search Results

The Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model incorporated fuel economy and electricity use of alternative fuel/vehicle systems simulated by the Powertrain System Analysis Toolkit (PSAT) to conduct a well-to-wheels (WTW) analysis of energy use and greenhouse gas (GHG) emissions of plug-in hybrid electric vehicles (PHEVs). Based on PSAT simulations of the blended charge depleting (CD) operation, grid electricity accounted for a share of the vehicle’s total energy use ranging from 6% for PHEV 10 to 24% for PHEV 40 based on CD vehicle mile traveled (VMT) shares of 23% and 63%, respectively. Besides fuel economy of PHEVs and type of on-board fuel, the type of electricity generation mix impacted the WTW results of PHEVs, especially GHG emissions.

The objective of this study is to optimize the injector power drive system for improved fuel injection quantity and timing control. The power drive system was optimized for improved injection repeatability under different operating conditions such as fuel supply pressures. A coupled simulation of injector electromagnetic, pintle (needle) rigid body motion and computational fluid dynamics (CFD) model was employed to generate the optimal values of the 1st stage current, the 1st stage on-time and the 2nd stage current. The simulation results were validated against the experimental data measured with a photo detector measurement system.

Many Small Unmanned Aerial Vehicles (SUAV) are driven by small scale, fixed blade propellers. Flow produced by the propeller can have a significant impact on the aerodynamics of a SUAV. Therefore, in Computational Fluid Dynamic (CFD) simulations, it is often necessary to simulate the SUAV and propeller coupled together. For computational efficiency, the propeller can be modeled in a steady-state view by using momentum source terms to add the thrust and swirl produced by the propeller to the flow field. Many momentum source term models are based on blade element theory. Blade element theory divides the blade into element sections in the spanwise direction and assumes each element to operate independently as a two-dimensional (2D) airfoil.

It is important for engineering firms to be able to develop forecasts of recommended courses of action based on available information. In particular, engineering firms must be able to assess the benefit of performing information-gathering actions. For example, an automobile manufacturer may use a computer simulation of a hydraulic motor and pump in the design of a new vehicle. The model may contain random variables that can be more accurately determined through expensive information-gathering actions, e.g., physical experiments, surveys, etc. To decide whether to perform these information-gathering actions, the automobile manufacturer must be able to quantify the expected value to the firm of conducting them. However, the cost of computing the expected value of information (through optimization, Monte Carlo sampling, etc.) grows exponentially with the amount of information that is to be gathered and can often exceed the cost of actually gathering the information.

This paper presents calculations of engine flows by using the Partially-Averaged Navier Stokes (PANS) method (Girimaji [1]; [2]). The PANS is a scale-resolving turbulence computational approach designed to resolve large scale fluctuations and model the remainder with appropriate closures. Depending upon the prescribed cut-off length (filter width) the method adjusts seamlessly from the Reynolds-Averaged Navier-Stokes (RANS) to the Direct Numerical Solution (DNS) of the Navier-Stokes equations. The PANS method was successfully used for many applications but mainly on static geometries, e.g. Basara et al. [3]; [4]. This is due to the calculation of the cut-off control parameter which requires that the resolved kinetic energy is known and this is usually obtained by suitably averaging of the resolved field. Such averaging process is expensive and impractical for engines as it would require averaging per cycles.

Research interests in autonomous driving have increased significantly in recent years. Several methods are being suggested for performance optimization of autonomous vehicles. However, weather conditions such as rain, snow, and fog may hinder the performance of autonomous algorithms. It is therefore of great importance to study how the performance/efficiency of the underlying scene understanding algorithms vary with such adverse scenarios. Semantic segmentation is one of the most widely used scene-understanding techniques applied to autonomous driving. In this work, we study the performance degradation of several semantic segmentation algorithms caused by rain for off-road driving scenes. Given the limited availability of datasets for real-world off-road driving scenarios that include rain, we utilize two types of synthetic datasets.

Advanced Driver Assistance Systems (ADAS) like Lane Departure Warning (LDW) and Lane Keep Assist (LKA) have been available for several years now but has experienced low customer acceptance and market penetration. These deficiencies can be traced to the inability of many of the perception systems to consistently recognize lane markings and localize the vehicle with respect to the lane markings in the real-world with poor markings, changing weather conditions and occlusions. Currently, there is no available standard or benchmark to evaluate the quality of either the lane markings or the perception algorithms. This work seeks to establish a reference test system that could be used by transportation agencies to evaluate the quality of their markings to support ADAS functions that rely on pavement markings. The test system can also be used by designers as a benchmark for their proprietary systems.

As autonomous vehicles continue to grow in popularity, it is imperative for engineers to gain greater understanding of vehicle modeling and controls under different situations. Most research has been conducted on on-road ground vehicles, yet off-road ground vehicles which also serve vital roles in society have not enjoyed the same attention. The dynamics for off-road vehicles are far more complex due to different terrain conditions and 3D motion. Thus, modeling for control applications is difficult. A potential solution may be the incorporation of empirical data for modeling purposes, which is inspired by recent machine learning advances, but requires less computation. This thesis proposal presents results for empirical modeling of an off-road ground vehicle, Polaris XP 900. As a first step, data was collected for 2D planar motion by obtaining several velocity step responses. Multivariable polynomial surface fits were performed for the step responses.

A major decision to make in design projects is the selection of the best technology to provide some needed system functionality. In making this decision, the designer must consider the range of technologies available and the performance of each. During the useful life of the product, the technologies composing the product evolve as research and development efforts continue. The performance evolution rate of one technology may be such that even though it is not initially a preferably technology, it becomes a superior technology after a few years. Quantifying the evolution of these technologies complicates the technology selection decision. The selection of energy storage technology in the design of an electric car is one example of a difficult decision involving evolving technologies.

Tradeoff studies are a common part of engineering practice. Designers conduct tradeoff studies in order to improve their understanding of how various design considerations relate to one another and to make decisions. Generally a tradeoff study involves a systematic multi-criteria evaluation of various alternatives for a particular system or subsystem. After evaluating these alternatives, designers eliminate those that perform poorly under the given criteria and explore more carefully those that remain. One limitation of current practice is that designers cannot combine the results of preexisting tradeoff studies under uncertainty. For deterministic problems, designers can use the Pareto dominance criterion to eliminate inferior designs. Prior work also exists on composing tradeoff studies performed under certainty using an extension of this criterion, called parameterized Pareto dominance.

EcoCAR 2: Plugging In to the Future is a three-year design competition co-sponsored by General Motors and the Department of Energy. Mississippi State University has designed a plug-in hybrid powertrain for a 2013 Chevrolet Malibu vehicle platform. This vehicle will be capable of 57 miles all-electric range and utility-factor corrected fuel economy of greater than 80 miles per gallon gasoline equivalent (mpgge). All modifications are designed without sacrificing any of the vehicle's utility or performance. Advanced modeling, simulation, and Hardware-in-the-Loop (HIL) simulation capabilities are being used for rapid control prototyping and vehicle design to ensure success in the following years of the competition.

There is significant potential for connected and autonomous vehicles to impact vehicle efficiency, fuel economy, and emissions, especially for hybrid-electric vehicles. These improvements could have large-scale impact on oil consumption and air-quality if deployed in large Mobility-as-a-Service or ride-sharing fleets. As part of the US Department of Energy's current Advanced Vehicle Technology Competition (AVCT), EcoCAR: The Mobility Challenge, Mississippi State University’s EcoCAR Team is redesigning and doing the development work necessary to convert a conventional gasoline spark-ignited 2019 Chevy Blazer into a hybrid-electric vehicle with SAE Level 2 autonomy. The target consumer segments for this effort are the Mobility-as-a-Service fleet owners, operators and riders. To accomplish this conversion, the MSU team is implementing a P4 mild hybridization strategy that is expected to result in a 30% increase in fuel economy over the stock Blazer.

In this work, a process-structure-property relationship for additively manufactured Al-Si-Mg alloy was constructed, with the aid of an integrated multi-physics model. Specifically, first, a series of thermal simulations were performed to understand molten pool geometry under different additive manufacturing (AM) operating conditions, including laser beam power, scanning speed, and hatch spacing. The porosity formation was predicted based on thermal simulation results, which yield molten pool dimension information for predicting the lack-of-fusion porosity. Dream.3D was utilized to reconstruct synthetic microstructures with different volume fraction of porosity.

A Thin Film Thermocouple (TFT) surface micro-machined on a Pyrex wafer was used to study micro-scale features in nucleate boiling. This study is relevant for various aerospace applications such as spray cooling, energy conversion devices and materials processing. The K-Type TFT was ~50 microns wide and ~250nm thick. A high speed digital data acquisition system was used to record the surface temperature fluctuations during pool boiling of PF-5060. The surface temperature transients were obtained at different superheats and data acquisition sampling rates up to 1 kHz. The spectra of surface temperature transients were analyzed using Fast Fourier Transform (FFT).

The current research conducted a cross-validation between an infrared motion capture system and an electromechanical motion capture device. No differences were found between the motion capture methods in shoulder and elbow angles. However, differences were found between the motion capture methods on distances of hand movements and actor location in space. Results of the current study indicate electromechanical motion capture devices are too inaccurate to use for validating digital human models unless the ultimate application of the model does not require millimeter accuracy or an absolute location in space. If one is primarily interested in joint angles, and distances are secondary, an electromechanical device is acceptable.

Recently [1, 2, 3 and 4], the novel Advanced (injection) Low Pilot-Ignited Natural Gas (ALPING) low-temperature combustion (LTC) concept was demonstrated to yield very low NOx emissions (<0.2 g/kWh) with high fuel conversion efficiencies (>40%). In the ALPING-LTC concept, very small diesel pilot sprays (contributing ∼2-3 percent of total fuel energy) are injected early in the compression stroke (60°BTDC) to ignite lean, homogeneous natural gas-air mixtures. To simulate ALPING-LTC, a phenomenological thermodynamic model was developed. The cylinder contents were divided into an unburned zone containing fresh natural gas-air mixture, several packets containing diesel and entrained natural gas-air mixture, a flame zone, and a burned zone. The simulation explicitly accounted for pilot injection, spray entrainment, diesel ignition (with the Shell autoignition model), spray combustion of diesel and entrained natural gas, and premixed turbulent combustion of the natural gas-air mixture.

The Mississippi State Challenge X team has built a new rear cradle for its 2005 Chevy Equinox hybrid, which allows for the integration of a Ballard electric drive system. The OEM cradle would have required extensive modification for the installation of the Ballard unit. The new cradle will save space by utilizing smaller members with thicker walls, thereby permitting more flexibility in mounting the drive. The team developed a working model of the MSU cradle that serves the duties of the existing cradle and allows the Ballard drive to be installed. Analytical calculations were performed to determine the loads experienced by the cradle during on-road service. A stress analysis was then performed using these loading criteria. The MSU team determined that mechanical testing would be the fastest way to analyze the stiffness of the original part. Two mechanical tests were performed to determine the part's stiffness.

An engine cycle simulation which included the second law of thermodynamics was used to examine the engine performance and the thermodynamic characteristics of a spark ignition engine as functions of the oxygen inlet concentration. A wide range of oxygen inlet concentrations (12% to 40% by volume) was considered. For oxygen inlet concentrations less than 21%(v), EGR was used, and for oxygen inlet concentrations greater than 21%(v), oxygen enriched inlet air was used. Two EGR configurations were considered: (1) cooled and (2) adiabatic. In general, engine efficiencies decreased, heat transfer increased, nitric oxide emissions increased, and the destruction of availability (exergy) decreased as the oxygen concentration increased.

The advantages of having higher stiffness to weight ratio and strength to weigh ratio that composite materials have resulted in an increased interest in them. In automotive engineering, the weight savings has positive impacts on other attributes like fuel economy and possible noise, vibration and harshness (NVH). The driveline of an automotive system can be a target for possible use of composite materials. The design of the driveshaft of an automotive system is primarily driven by its natural frequency. This paper presents an exact solution for the vibration of a composite driveshaft with intermediate joints. The joint is modeled as a frictionless internal hinge. The Euler-Bernoulli beam theory is used. Lumped masses are placed on each side of the joint to represent the joint mass. Equations of motion are developed using the appropriate boundary conditions and then solved exactly.

Biodiesel remains an alternative fuel of interest for use in diesel engines. A common characteristic of biodiesel, relative to petroleum diesel, is a lowered heating value (or energy content of the fuel). A lower heating value of the fuel would, presuming all other parameters are equal, result in decreased engine torque. Since engine torque is often user-demanded, the lower heating value of the fuel generally translates into increased brake specific fuel consumption. Several literature report this characteristic of biodiesel. In spite of the wealth of fuel consumption characteristic data available for biodiesel, it is not clear how other engine performance parameters may change with the use of biodiesel. Characterizing these parameters becomes complicated when considering the interactions of the various engine systems, such as a variable geometry turbocharger with exhaust gas recirculation.