Search Results

Flash boiling spray is effective in improving the atomization and evaporation characteristics for gasoline direct injection engines. However, for a multi-hole injector the morphology structure of spray has an obvious change with the fuel temperature increasing or the ambient pressure decreasing, which influences the process of mixture formation and flame propagation. Specially, the spray collapses with both long penetration and a narrow spray angle above certain high superheat degree, which deteriorates air/fuel mixing and hence increases emissions. It is not desired for engine applications while the mechanism of spray structure transformation for multi-hole injector still remains unclear. In the present study, a systematic flash boiling spray model for multi-hole injector is built to investigate the flash boiling spray of multi-hole injector.

In-cylinder flow characteristics in a four-stroke diesel engine were studied experimentally by instantaneous measurements of swirl and squish flow velocity distribution with particle image velocimetry (PIV). The triple-exposed PIV films were interrogated on a self-made system to get the velocity distribution. The measured velocities were analyzed by spatially high-pass and low-pass filtering techniques. Vorticity distributions were also calculated using the measured data. As results, vortex structure of the flow field was clearly visualized. Spatially averaged in-cylinder flow energy was found decaying at high rate but the less-scaled flow components at much lower rate. Clearly visualized squish and reverse squish movements around the top dead center (TDC) during the compression stroke were found strongly affecting the swirl flow field. making the in-bowl flow energy increased.

Chinese new legislations on two wheels and mopeds have been published recently. Depending on the latest exhaust statistic analyses, with the resulting of tighter limits, the application of catalytic converters is becoming a prevalent and a cost-efficient solution for Chinese motorcycle manufacturers. The phenomenon of exhaust temperature changes rapidly during real driving process is well known as one of major destructive factors which have effects upon converter's durability. One 125 cm3 motorcycle is selected as a typical model in this research project. Exhaust temperature of the 125 cm3 motorcycle is measured and recorded during the process of ECE 40 driving cycle. A simulation test system has been set up successfully depending on those temperature data. Conversion ratio of converter sample lost distinctly after 18 hours' thermal impact tests. After further analyses, there were not evident changes in microstructure and substance on the surface of converter.

Matching fuel injection and airflow motion is critical for the optimization of fuel-air mixing and combustion process in diesel engines. In this study, the effects of swirl flow on liquid droplet motion and the selection of swirl ratio, which are known as the major concern in organizing airflow motion, were investigated based on theoretical analysis of droplet trajectories. The evaporating droplets with various initial conditions are assumed to be transported in a solid-body-like swirl field, and their trajectories were derived based on force analysis. To evaluate fuel-air mixing quality, a new parameter with respect to fuel vapor distribution was proposed. Based on this methodology, the effects of swirl velocity, droplet size, as well as liquid-gas density ratio on droplet trajectory were discussed under diesel-engine-like boundary conditions.

Using a Laser Doppler Velocimetry with Burst Spectrum Analyzer (LDV-BSA), droplet velocities of a diesel fuel spray under a pressure higher than 100 MPa were measured at different points within the spray profile. Results show that although the mean velocity distribution at the sampling plane is rather uniform, the number-based droplet velocity distributions of two sampling points at the same plane are different. The conclusions agree with theoretical predictions through maximum entropy principle qualitatively.

It is found that a thin and rich mixture layer on a wall is formed after impingement of a gas jet of fuel on the wall. The measured thickness of the mixture layer is about 2 mm. and its dispersion rate after the end of injection is much lower, compared to that of a space gas jet. This phenomenon in a small D.I. diesel engine is known as “wall wetting” or “wall fuel accumulation” which has an important influence on engine fuel consumption and emissions. This paper presents a technique for enhancing the near wall mixing of an impinging jet by means of a bump on the wall. The development of a wall jet formed after an impingement of a gas jet has been investigated by simultaneously measuring the near wall velocity and concentration distribution. It has been found that a wall jet is stripped off the wall and ejected as a secondary jet when the wall jet encounters a bump of the wall.

Although excellent progress has been made recently in powertrain fault diagnosis based on vibration signals, most of them are based on the assumption that the fault features of the training and test data are drawn from the same probability distribution. Due to the limitation of the domain shift phenomenon, the performance of the current intelligent fault diagnosis methods is significantly reduced. Even many existing transfer learning methods have the problem of low generalization ability. Inspired by sparse representation theory, a novel cross-domain fault diagnosis method based on K-means singular value decomposition (K-SVD) and long short-term memory network (LSTM) is proposed in this study. First, K-SVD can convert source domain data into a sparse dictionary and sparse coefficient. The domain-invariant features are explored in the sparse dictionary, which contains redundant features. The sparse coefficients are input into the LSTM to obtain a primary classifier.

A new two-dimensional wall-flow DPF microstructure model has been developed in this paper to investigate the particle deposition distribution in DPF channels and the deep-bed filtration process of DPF. The substrate wall of the DPF having a thickness of L is divided into several layers with a uniform thickness of Δy along the cross-wall direction, and each layer has specific porosity and pore size. The pressure drop, particle deposition distribution and the dynamic deep-bed filtration process of the DPF with inhomogeneous wall structure are studied under various space velocities. Besides, the differences on DPF’s performance brought by the inhomogeneous wall structure are discussed by comparing with a homogeneous wall structure.

OH, soot and temperature distributions of wall-impinging diesel fuel spray were investigated in a high-temperature high-pressure constant volume combustion vessel. The ambient temperature (Ta) was set as 773 K, and the wall temperature (Tw) was set as 523 K, 673 K, 773 K, respectively. Three different injection pressures (Pi) of 60 MPa, 100 MPa, 160 MPa, and the ambient pressures (Pa) of 4 MPa were applied. The OH spatial distributions of wall-impinging spray were measured by the method of OH chemiluminescence imaging. Two-color pyrometry was applied to evaluate the spatial distributions of KL factor and flame temperature of wall-impinging spray. The results reveal that, OH chemiluminescence is observed in the region near the impingement point firstly. The regions of high OH chemiluminescence intensity and high KL factor appear in the location near the wall surface along the whole combustion process.

In order to achieve high precision measurement with low manufacturing process, we propose a new angular displacement measurement method, which uses light filed as a measurement medium and can realize simultaneous measurement of whole circumference. Firstly, through the orthogonal modulation of time and space for the ring light field, four channels of standing wave light field uniformly distributed along the circumference are obtained. Then, electric traveling wave signal is synthesized by photoelectric conversion and phase-shifting processing. Finally, the angular displacement is measured by using the method of phase discrimination through calculating the phase difference between electric traveling wave signal and reference signal. Through the derivation of the sensor measurement principle, the error characteristics of the sensor caused by non-uniform distribution of light field are analyzed.

The performance of three different electric turbo-compounding systems under both steady and driving cycle condition is investigated in this paper. Three configurations studied in this paper are serial turbo-compounding, parallel turbo-compounding and electric assisted turbo-compounding. The electric power, global gain of the whole system (engine and power turbine) under steady operating condition is firstly studied. Then investigation under three different driving cycles is conducted. Items including fuel consumption, engine operating point distribution and transient response performance are analyzed among which the second item is done based on statistic method combined with the results obtained under steady operating conditions. Study under steady condition indicates that electric assisted turbo-compounding system is the best choice compared with the other two systems. The performance of serial turbo-compounding is load oriented while parallel configuration is speed oriented.