Search Results

This research developed a new measurement technology for thermal analysis of the heat radiation from a hybrid transaxle case surface to the air and improved the heat radiation performance. This heat flux measurement technology provides the method to measure heat flux without wiring of sensors. The method does not have effects of wiring on the temperature field and the flow field unlike the conventional methods. Therefore, multipoint measurement of heat flux on the case surface was enabled, and the distribution of heat flux was quantified. To measure heat flux, thermal resistances made of plastic plates were attached to the case surface and the infrared thermography was used for the temperature measurement. The preliminary examination was performed to confirm the accuracy of the thermal evaluation through heat flux measurement. The oil in the transaxle was heated and the amount of heat radiation from the case surface was measured.

This paper provides an overview of automotive electronic systems put into products over the past decade, and describes automotive electronics which have been demonstrated in experimental cars. In addition, future electronic systems found to be promising for the practical use in coming years and the direction of development of electronics are also discussed, as an extention of the overview mentioned above.

The hybrid system has the typical advantage that it can realize various types of system control, because the system has two power units, engine and motor. On the other hand, however, constraints are increasing due to the complexity of the vehicle system. Compared to the conventional HILS construction and application, there are mainly two typical characteristics or themes for HV-HILS (i.e. HILS for hybrid vehicle control development). Firstly, HV-HILS requires full vehicle simulation environment, because the plural ECU control logic is intricately intertwined. Secondly, recent HILS system needs to run with more accurate or complicated plant models which are necessary to develop more accurate vehicle control logic.

Electronic Control Units (ECUs) for automobiles are usually composed of a main single-chip microcomputer and peripheral circuits with some standard and/or custom ICs. The peripheral circuits vary with the kinds of control or models of automobiles. When the peripheral circuits are replaced with a single-chip microcomputer, the ECU becomes compact and low in cost. This is because the ECU is constructed with only two LSIs and can be used for various kinds of control and various models of automobiles only by changing the program of the microcomputer. The microcomputer, however, requires many I/O functions and high reliability. We have developed a new 4-bit microcomputer suitable for these requirements. The new microcomputer has two remarkable features. One is powerful I/O functions such as high speed I/O, serial I/O, parallel I/O, analog I/O, and default output that is generated in place of the calculated output by the main CPU when it fails.

A new ABS and Traction control system (TRAC system) has been developed and put into mass production in a new model LEXUS LS400. The TRAC system controls Sub-Throttle Valve and brake hydraulic pressure independently for left and right wheels. To realize the ABS and TRAC system,it is necessary for the Electronic Control Unit (ECU) to process complex algorithm and high speed calculation. The ABS and TRAC ECU for LEXUS LS400 is constructed by 3 TOYOTA custom 8-bit single chip microcomputers. Each CPU performs wheel speed calculation,ABS control and TRAC control,sharing the common data through high speed serial communication. This paper describes the function of each CPU,the method of CPU communication and fail safe function in the ECU.

Toyota has developed a new continuously variable transmission (CVT) named “Super CVT”. The Super CVT has a wide ratio coverage and adopts a newly developed integrated control system with a direct injection gasoline engine (D-4) equipped with electronically controlled throttle. The combined package has achieved good fuel economy and a high overall level of performance. This paper shows the major features and performance of the Super CVT.

In order to further improve the performance of NOx storage-reduction catalysts (NSR catalysts), focus was placed on their high temperature performance deterioration via sulfur poisoning and heat deterioration. The reactions between the basicity or acidity of supports and the storage element, potassium, were analyzed. It was determined that the high temperature performance of NSR catalysts is enhanced by the interaction between potassium and zirconia, which is a basic metal oxide. Also, a new zirconia-titania complex metal oxides was developed to improve high temperature performance and to promote the desorption of sulfur from the supports after aging.

On board multiplexing communication system is regarded as a necessary technology for the future of electronic system in automobiles. Many companies are developing multiplexing systems and the ISO and SAE are active in establishing standards for communication protocols. The proposed communication protocol specifications have different specifications. Consequently, no compatible evaluation standards existed, and it was difficult to compare one protocol to another. Therefore, to assist the standardization activities of the IS0 and SAE, we have developed an evaluation method for distributed multiplexed communication systems and evaluated each of the proposed protocols using this method. These evaluations were performed from the point of view of the future users of these systems. In this paper we present the results of the experiments on distributed multiplexed communication systems each of which consists of communication IC and the proposed physical layer.

A smart analog integrated circuit (IC) is developed for use in an electronic control unit for an automotive variable power-steering system. This IC accepts a vehicle speed signal as its input, performs signal processings such as frequency to voltage conversion and function generation, and then as its output generates a pulse width modulated (PWM) signal whose duty corresponds precisely to a given piecewise linear function of the vehicle speed. The PWM output is used as a driving signal to a power MOSFET for the actuation and control of a linearly variable solenoid valve to vary the force needed for steering effort in a prescribed relation to the vehicle speed. The IC is fabricated by monolithic bipolar integrated circuit technology and has about 750 device elements in a chip size of 5.7 by 3.1 mm2. It is enveloped in a shrinked dual in-line package with 24 pins.

This paper describes the development of the electrical systems for the integrated control system which unified automobile electronic control systems and led to a dramatic improvement in vehicle dynamics. An outline of the system is presented first, followed by actual automobile application examples of electrical systems employing medium-speed multiplexing.

With the increasing use of electronic control systems to improve vehicle dynamics, there is an ever growing need to transfer control information among electronic control units(ECUs). To meet this need, a protocol was proposed for high-speed multiplex in the previous SAE paper 910463. Based on the paper, a prototype IC for high-speed multiplexing control was developed. First, a further analysis was made of the information which is transferred among ECUs. As a result, it was found that the information has certain distinctive characteristics. These characteristics are so distinctive that it may be relevant to devise a new protocol for communication. Based on the analysis, a new form of token passing method was implemented. By using this method, it is easy to calculate transmission latency time. So this method is suitable for a real time control application like vehicle dynamics control.

Several methods have been studied by using adaptive control in order to tune parameters of the cruise control automatically. But theoretical analysis has not been done by the reason of severe non-linearity. In this paper, a vehicle dynamics model is made with theoretical analysis, and two adaptive control methods to assist the conventional PID controller are proposed.

With an ever growing demand for the enhanced control of a vehicle and for the reduction of power and signal distributing wires in a vehicle, there is a pressing need for the development of Local Area Network (LAN) in a vehicle. LAN enables the exchange of various data among several electronic control units (ECUs), and results in the higher controlled performances of a vehicle and the reduction of the wires. In response to this need, two integrated circuits for vehicle multiplexing communication are developed. One is a communication control IC and the other is a bus driver/receiver IC, both based upon the standard of a PWM type of the J1850 for a communication protocol. The communication control IC is designed to have distinctive features such as a highly fail-safe operation and the reduction of the overhead for communication imposed on a central processing unit (CPU) of the ECU.

It is widely known that pellet-typed catalysts are deactivated by phosphorus (ZnDTP) that comes from engine oils. In this paper, the poisoning of monolithic three-way catalysts and oxygen sensors by engine oils is studied. First, catalysts and oxygen sensors were poisoned on the engine bench by test oils in which the quantity of phosphorus and ash was varied. Next, performance of the catalysts and sensors alone was examined and the vehicle exhaust emission at FTP mode was measured on a chassis dynamometer. The results indicate that phosphorus in engine oils poisons the monolithic catalyst and the oxygen sensor resulting in deterioration of the vehicle NOx exhaust emission. However, Ca sulfonate and Mg sulfonate detergents act by restraining phosphorus poisoning of the catalyst and the oxygen sensor. Through analysis of the catalyst and sensor surfaces, it is concluded that phosphorus poisons the catalyst and sensor forming a dense coating.

This paper describes the multiplex communication protocol, BEAN (Body Electronics Area Network), developed for body control system on passenger cars which in recent years has increased the scope of multiplex communication. BEAN is based on a protocol developed in 1992 (SAE920231) but expands upon the performance in areas, such as the suitability of the ID system for increase of ECUs, the variable data length enabling the transmission of diagnostic data, and the transmission rate, while keeping the cost and radiation noise level low. The software size of BEAN is compact enough to be implemented by general purpose 8bit MCUs which have recently seen improvements in performance. The BEAN communication devices are available corresponding to the scale of the application and configuration of the ECU taking into account the software capability. This protocol was evaluated using simulation with the body control system on luxury passenger cars.

Toyota succeeded in the fall of 1984 in manufacturing a complex engine and transmission control system using a newly developed single-chip microcomputer. This microcomputer, equipped with an 8K-byte ROM ( Read Only Memory) and a 256-byte RAM ( Random Access Memory), a powerful real time processing function, and a high-speed optimum instruction set, is better suited for automobiles. Application of the latest CMOS technology has enabled lower power consumption and improved noise immunity. The new system, which includes a new function; the electronic spark advance with knock control in addition to the conventional sophisticated system, has greatly improved the performance and driveability of vehicles.

The deactivation process of automotive catalysts by lead and phosphoruos were studied. The accelerated poisoning test were performed. The activity evaluation and characterisation of poisoned pellet oxidation catalysts showed the following origin of poisoning deactivations. Lead interacts with active materials and phosphorus covers over catalysts to reduce these catalytic performance. In the case of phosphorus and lead co-existence, the activity decreases rapidly because leadphosphate plugges pores of the support. In monolithic catalysts, highly axial distributions of poisons was obserbed. This characteristic distribution is advantageous for the durability of the catalyst.

Engine control systems were the precursor of scale automotive electronics systems using microcomputers. Toyota Motor Corporation introduced high - level, total control of the power train by applying system integration through introducing a multi - CPU system to the 1988 MY Toyota Camry. Integration in the ECU has been promoted to parallel with system integration. By adopting single - chip microcomputers, monolithic ICs, and hybrid ICs all designed and developed for car electronics, and semiconductor barometric pressure sensors for car electron into ECU's. etc. ever - expandable functions can be provided in a smaller and more lightweight ECU package with higher reliability.

This paper describes an analysis of the rise in timing belt temperature occuring under high engine speed operation that was made to establish the cause of heat deterioration of the belt materials. Surface temperatures of the belt were accurately measured by correcting thermo-vision detected radiations to eliminate environmental radiation. The temperature profile of a belt cross-section was obtained by a specially developed thermo-couple device. The experimental results indicated that heat generated by the belt contributes significantly to the temperature rise and that the primary cause of the heat generation is bending hysteresis of the belt cords. In addition, a description is made of a method of calculating the rate of heat generation in the belt. In this simulation method, the energy dissipated as heat is calculated from the bending strains and loss moduli of the belt materials. Calculated results were found to agree well with experimental results.

A system to measure transient temperature distribution on the brake disc rotor at high speed braking has been developed and its measuring principle and configuration were discussed in this paper. This system consists of two revolution sensors and two sets of optical fiber array, photoelectric elements, and microprocessor, which fiber array is so arranged that it faces the brake disc rotor. This new system has the following features: (1) Measuring is made using a visible radiation wavelength range for red hot temperatures higher than 550°C.