Search Results

In this paper, it is developed a descriptive theory of paraglider flight mechanics, a gliding aircraft designed for entertainment purposes. After the analytical representation of the equipment geometry, the equations of longitudinal motion are derived and the most relevant parameters of performance and stability are identified. The developed theory is tried out based on real gliders analysis showing consistent results. The theoretical results here presented about paraglider flight mechanics can not be found in the available bibliography. It's expected that a scientific approaching of the paraglider stability and performance, as a branch in the aeronautic engineering field enables relevant improvements on flying and safety characteristics of these unconventional aircrafts.

Driven by the necessity to reduce costs and improve products quality the automotive industry replaced the design method known as "trial and error" by those grounded on mathematical and physical theory. In this context, a longitudinal performance test was made by BAJA SAE UFMG team, in order to acquire vehicular performance data that will be used to validate computer models. The methodology consists of sensors and data acquisition system research, validation, fixation and installation in the vehicle, test and process of acquired data. From these steps, correlated data were acquired from magnitudes such as angular velocity in transmission shafts, global longitudinal acceleration and velocity, travel of break and throttle pedals and pressure inside of master cylinder. These results developed the knowledge about vehicular dynamic allowing the improvement of futures prototypes.

In this work, sailplane symmetrical motion equations including pitch motion controlled by elevator angle are presented. The following effects are especially taken into consideration: i) tail damping due to pitch motion; ii) air density variation according to altitude; iii) presence of vertical and horizontal atmospheric air motions, and iv) non-linearity of CL ′ a curve near stall angle. The mathematical modeling includes the construction of an objective function for competition flight optimization. Making use of the concept of state variables, the minimum time trajectory problem is formulated as an optimal control problem with state constraints. Using simplified control laws and a mathematical programming algorithm, suboptimal trajectories are obtained for the sailplane PIK-20B.

This work presents a full analysis of a bi-fuel engine converted to natural gas and aims to survey the main performance losses and the advantages in specific consumption and toxic emissions. With this purpose, dynamometric tests and curves survey of a Fiat Palio 1.6, 16V engine, according to Standard NBR ISO 1585. Tests were made using diverse mixers, trying to obtain the losses caused by this device when the engine is working with gasoline, after the conversion. Tests were performed for different ignition advances, with manual and electronic VNG flow control systems. Trials for many differents low gear engine regulation, looking for consumption reduction and lower emission rates. The gas pressure reducer was tested with and without heating, showing differents results, mainly for emission rates. Other than comparing different components and different engine operation conditions, an analysis of two different natural gas conversion kits were performed, both extensile used in Brazil.

Using a Simple Genetic Algorithm, the present paper obtains the optimal geometry of a cam with roll follower. In order to evaluate cam performance, an objective function which takes into account the influence of the inertia, the perimeter and of the pressure angle is proposed. The choice for a Genetic Algorithm is justified because, in preliminary tests, the objective function had proven to be multimodal

A multi-hole direct injection injector was studied by means of image analysis. Methodologies based on an automatic process of cone angle measurement and edge detection were applied for the spray images generated by a 100 bar injection pressure discharged into a pressurized rigid chamber. A criterion based on pixel values was taken to localize the spray edges as angular coordinates and also with x and y position data. The high pixel values were associated with liquid phase while the low pixel values were associated to its absence. Computational codes written in MATLAB environment were used to analyze the numerical matrices associated to the images. Using the written MATLAB codes, a comparison of the effect of atmospheric back pressure, inside the chamber, on the spray pattern, cone angle and spray penetration were evaluated. The chamber was pressurized with 2.5, 5.0, 7.5 and 10 bar of back pressure. The tested fluid injected was EXXSOL D60 for simulating ethanol fuel behavior.

Global climate change and an increasing energy demand are driving the scientific community to further advance internal combustion engine technology. Invented by Sr. Henry Ricardo in 1918 the torch ignition system was able to significantly decrease engine’s fuel consumption and emission levels. Since the late 70s, soon after the Compound Vortex Controlled Combustion (CVCC) created by Honda, the torch ignition system R&D almost ceased due to the issues encountered by very complex and costly mechanic control systems that time. This work presents a stratified torch ignition prototype endowed with a sophisticated electronic control systems and components such as electro-injectors from direct injection systems placed on the pre-combustion chamber. The torch ignition prototype was tested and its performance are presented and compared with the baseline engine, which was used as a workhorse for the prototype engine construction.

Reducing environmental pollution by the transport sector has been influenced according to the increasingly restrictions imposed by regulatory standards. For this, legislation such as Euro (at global level) and Proconve (at local level) set new limits each new phase, usually stipulating reductions in the levels of greenhouse gas emissions. Compliance with these requirements is seen with the vehicle or engine ratings working through the conditions imposed by a standard test cycle. However, standard driving conditions often do not represent the real-world driving conditions, being influenced by relief, traffic lights and other peculiarities of each city or route. This paper aims to compare real-world driving cycles of urban bus and passenger car in the city of Santa Maria, in southern Brazil, with the conditions used for light gasoline vehicles and heavy diesel vehicles approval.

Resistive forces are a great source of fuel consumption in vehicles. In particular, rolling resistance represent the major resistance force at low speeds. It is highly influenced by the inflation pressure of the tire and vertical load over it. In the present work, a computer model is created with the objective of investigating the influence of tire inflation pressure on fuel consumption and rolling resistance force. Pressure is varied and parameters analyzed at different vehicle speeds for two different calculation methods. Results show significant decrease in fuel consumption and rolling resistance force as inflation pressure is augmented.

For metallic tanks in contact with aqueous solution, it is always observed the presence of electrochemical corrosion. This process can cause both economic and environmental damage. In the automotive industry, fuel tanks systems have been studied in order to propose new materials to replace the plastic tanks or tanks with metallic coatings. Plastic tanks have the disadvantage of not being recyclable. In the other hand, for metallic coated tanks, tin is used as a coat material and, for this reason, the external tank side must be painted, making its productive process more expensive and generating higher amount of waste. Nowadays, organic-metallic coated tanks, in which, nickel and aluminum are the metals present, can be found. These coatings show potential application; because they do not use heavy metals in their composition and they do not require external painting, allowing a lower production cost.

The focus of this study was to create a methodology to evaluate spray characteristics in a gasoline direct injection injector by means of an automatic process. Computational codes were used to get information about cone angle and breakup length based on images got from injection process. A mathematical function was created to locate the boundaries of the spray and the cone angle was studied as the angle of arcs situated within these boundaries. The centre of the arc was located on the orifice of the injector and a value of angle was associated with several distances from orifice. The breakup length was associated as a distance from the orifice of an arc formed by a group of pixels with the maximum standard deviation related to the values of these pixels. The velocity field was studied by the Particle Image Velocimetry technique. Three fluids were tested at this work: water, ethanol and gasoline.

The limited thermal efficiency in internal combustion engines provides a partial transformation of fuel energy in net power. The heat lost through the exhaust gases represent a significant portion of energy looses. The Seebeck Effect is the direct conversion of temperature differences between two dissimilar metals or semiconductors into electrical voltage. The present study demonstrates the application of thermoelectric generators technology in Baja SAE vehicles to recovery exhaust heat looses, using thermal energy converter devices. The electrical energy produced in Seebeck Effect Cells, assembly in engine exhaust manifold, is conditioned and applied in vehicle batteries and supply energy consumption during vehicle operation. This action could increase the vehicle energy efficiency by the recovery the thermal energy dissipated. This extra power supply makes possible the reduction of on board batteries charge capacity and also recharges them without external power sources.

This paper discusses the importance of vibration transmitted from the ground to the driver from the perspective of human whole-body vibration (WBV). The scope of analysis is to compare the main vehicle frequencies with those important from the human vibration health and comfort point of view. That was performed by mapping the vibration transmissibility present in different sub sections of the vehicle. The first is the transmissibility between the axles and the chassis rail, the following between the chassis rail and the cabin. The last would be between the cabin and the drivers' seat, although that was not possible from the acquisition point of view. The vehicles measured have mechanical suspension and elastomeric cabin coupling. It is known that all suspension systems in vehicle are highly nonlinear, although here linear dynamic analysis methods were used.

The present study introduces a proposal to improve the longitudinal performance of a land vehicle through the adoption of an unusual traction control system. The system is capable of improving the transfer of engine power to the ground and reduces the complexity of the task being performed by the driver. High-performance vehicles are able to achieve high levels of longitudinal acceleration and, sometimes, the power excess leads to the spinoff of the drive wheels, which decrease the ability of the tires to generate force, and consequently the vehicle acceleration. The proposed system acts in addition with the motor control, through the derivation of the motor speed signal, and its control by comparison with a predefined value. The control can delay or even suppress the ignition of the engine. Thus, the rate at which the engine gains speed, and consequently, the rate at which the vehicle accelerates, is limited.

Aiming the decrease of manufacturing costs, the automotive industry uses Computational Aided Engineering (CAE) and prototype testing for product development. In the field of simulation CAE could be performed using FEA (finite element analysis) or CFD (Computational Fluid Dynamic), the last one is the analysis of systems involving fluid flow, heat transfer and associated phenomena such as chemical reactions by means of computer-based simulation. One of the most important components of cooling system is a water pump which is evaluated through the fluid dynamic analysis. Therefore, this work aims to analyze the fluid flow inside an automotive water pump considering a three-dimensional steady-state using CFD, but also developing a methodology to evaluate it. The parameters of the analysis and the volumetric mesh were according to the simulated results approached the experimental results.

The aim of this work is to present the preliminary configuration design studies for an unmanned, lightweight (less than 15 kg), supersonic research aircraft. The studies comprise the aircraft typical mission, the aerodynamic and structural arrangement, preliminary performance, as well as mass distribution. The aircraft, an Unmanned Air Vehicle, or “UAV”, is named as Pohox (“arrow” in Maxakali indian language). It is intended to be the flying test bed for a multicycle engine capable to provide thrust in subsonic, transonic and supersonic regimes. In order to provide validation of the analysis tools, flight performance characteristics of a known, high speed aircraft - North American X-15 - have been also evaluated and compared with the available flight test data. The present analysis is an important step towards the aircraft detailed definition. And the features associated with the configuration obtained are good indications of the technical feasibility of this supersonic UAV.

This work shows procedures for analyzing sprays produced by a direct injection injector. The parameters studied were tip penetration, spray pattern, cone angles and velocity profiles. Two different experimental procedures were applied. The first one to get knowledge of the initial stage of injection consisted in recording images in 4000 Hz. With the data obtained, the penetrations and penetration rates were evaluated. The second experimental procedure consisted of using the Particle Image Velocimetry technique to get images and velocity data for getting knowledge of spray pattern, external and internal cone angle and velocity profiles of the spray fully developed. Gasoline and ethanol were the two fluids tested on the experiments. The results showed larger cone angles for gasoline, linear decreasing behavior for velocities on the linear velocity profiles and a transient stage for the magnitude of the velocities in the initial stage of injection.

To attend the new tendencies of the automotive market, new technologies must be used throughout the engine conception. One way of improving the project is to use computational numerical simulation, predicting engine behavior in a wide range of situations. This paper presents a methodology to estimate the engine characteristic parameters necessary to numerical simulation. Morse test was used to determine friction power, mean effective pressure friction and friction torque, considering the engine behavior during cylinder ignition cut-off. In this test all the results were compatible with manufacturer data, which validates the methodology. To define the moment of inertia, it's also proposed a fuel cut methodology, associated with the Morse test, because the torque values measured by dynamometer after the fuel cut did not correspond to the real value. Thus, plausible values of engine moment of inertia, very close to values obtained by software, were obtained.

In this work an algebraic model for the thermodynamic study of the compression-ignition engine is developed using the concept of efficiencies in the processes that compose the air standard cycle. In this model, the use of the efficiency concept added to the variation of the specific heat, the heat release based on Wiebe function, and variation of the initial instant of heat release and heat rejection, makes this no ideal cycle to approach the actual Diesel operation. A cinematic model of the crank-and-connecting rod mechanism is used to transform the gas work in axis torque. This model serves as didactic tool for the thermodynamic analysis of the compression-ignition engines operation.

Future engine control systems need suitable and accurate models for combustion. For this purpose, this paper presents a practical application of nonlinear autoregressive moving average polynomial models with exogenous inputs (NARMAX) technique to model pressure dynamics inside the cylinder of a direct injection compression ignition engine. Two models have been investigated taking two different sets of input variables. The first model only includes basic injection settings available from the electronic control unit. The second model uses the instantaneous crankshaft revolution speed as a main model input. Model parameter identification and validation are performed with experimental data obtained from a test engine equipped with a piezoelectric pressure sensor and with data computed from a thermodynamic-based engine cycle simulation code.