Search Results

Helmholtz resonators are often used in the design of vehicle mufflers to target tonal noise at a few specific low frequencies generated by the engine. Due to the uncertainty of temperature variations and different engine speeds, multiple resonators may have to be built in series to cover a narrow band of frequencies. Double-tuned Helmholtz resonators (DTHR) normally consist of two chambers connected in series. Openings or necks are created by punching small slots into a thin-walled tube which provide a natural neck passage to the enclosing volume of the Helmholtz resonator. In this paper, numerical analyses using both the boundary element (BEM) and the finite element (FEM) methods are performed and simulation results are compared against one another. A typical real-world muffler configuration commonly used in passenger vehicles is used in a case study.

The two-load method is used to measure the transmission loss of thin panels in two different sized impedance tubes (3.49 cm and 10.16 cm). Samples were initially tested with a clamped boundary condition. This was followed by tests with an elastomer inserted between the tube and tested sample to adjust the boundary condition at the periphery. In all tests performed, the influence of the sample holding method could not be removed from the test. The measured transmission loss was compared to finite element simulation with good agreement for both impedance tubes. Additionally, the effect of a compliant boundary condition along the periphery of the sample was also validated via simulation.

The insertion loss of louvered terminations positioned at the end of a rectangular duct is determined using acoustic finite element analysis. Insertion loss was determined by taking the difference between the sound power with and without the louvers at the termination. Analyses were conducted in the plane wave regime and the acoustic source was anechoic eliminating any reflections from the source. The effect of different louver configurations on insertion loss was examined. Parameters investigated included louver length, angle, and spacing between louvers. Based on the analyses, equations were developed for the insertion loss of unlined louvers.

Traditional manufacturing processes such as injection or compression molding are often enclosed and pressurized systems that produce homogenous products. In contrast, 3D printing is exposed to the environment at ambient (or reduced) temperature and atmospheric pressure. Furthermore, the printing process itself is mostly “layered manufacturing”, i.e., it forms a three-dimensional part by laying down successive layers of materials. Those characteristics inevitably lead to an inconsistent microstructure of 3D printed products and thus cause anisotropic mechanical properties. In this paper, the anisotropic behaviors of 3D printed parts were investigated by using both laboratory coupon specimens (bending specimens) and complex engineering structures (A-pillar). Results show that the orientation of the infills of 3D printed parts can significantly influence their mechanical properties.

Finite element modeling has been used extensively nowadays for predicting the noise and vibration performance of whole engines or subsystems. However, the elastomeric components on the engines or subsystems are often omitted in the FE models due to some known difficulties. One of these is the lack of the material properties at higher frequencies. The elastomer is known to have frequency-dependent viscoelasticity, i.e., the dynamic modulus increases monotonically with frequency and the damping exhibits a peak. These properties can be easily measured using conventional dynamic mechanical experiments but only in the lower range of frequencies. The present paper describes a method for characterizing the viscoelastic properties at higher frequencies using fractional calculus. The viscoelastic constitutive equations based on fractional derivatives are discussed. The method is then used to predict the high frequency properties of an elastomer.

This paper documents an inverse visible element Rayleigh integral (VERI) approach. The VERI is a fast though approximate method for predicting sound radiation that can be used in the place of the boundary element method. This paper extends the method by applying it to the inverse problem where the VERI is used to generate the acoustic transfer matrix relating the velocity on the surface to measurement points. Given measured pressures, the inverse VERI can be used to reconstruct the vibration of a radiating surface. Results from an engine cover and diesel engine indicate that the method can be used to reliably quantify the sound power and also approximate directivity.

This paper considers the use of partial enclosures and absorbing materials inside those enclosures to dissipate energy. Several experiments were conducted where various parameters of an enclosure were altered and the effect on the noise radiating through the opening was measured. From these results, the parameters that play the most important role in sound radiation through the opening of an enclosure were determined. The two-point method and decomposition theory were used to calculate the transmission loss, which was used as the primary variable to analyze the enclosure's performance; the transmission loss is shown to be a better variable than sound pressure or output sound power for this purpose. Numerical simulations were conducted using the indirect boundary element method, and the results were compared with experimental results.

This paper considers two questions: how does one know when a boundary element mesh is reliable, and what are the advantages and potential pitfalls of various methods for sound radiation prediction. To answer the first question, a mesh checking method is used. With this method velocity boundary conditions are calculated on the nodes of the mesh using a point source or sources placed inside the mesh. A boundary element program is then used to calculate the sound power due to these boundary conditions. The result is compared to the known sound power of the point source or sources. This method has been used to determine the maximum frequency of a mesh, how many CHIEF points to use, etc. The second question is answered by comparing the results of several numerical methods to experimental results for a running diesel engine. The methods examined include the direct and indirect boundary element methods and the Rayleigh integral.

The population of drivers over the age of 65 has been rapidly increasing since the early 1970's and this trend is expected to continue in the future. Aging could affect visual and cognitive abilities of elderly drivers and possibly impair their ability to operate a vehicle safely. This study examined the impact of this population on traffic safety over a 20-year period. The factors of age and cohort are examined to determine their influence on the crash involvement of elderly drivers. Age factors have been shown to be decisive in crashes resulting from complex situations, whereas cohort effects play a more dominate role in less demanding circumstances.

Over the past decade crash rates of younger drivers have been increasing despite a decrease in their driver population. This study examined specific driving maneuvers whose unsuccessful undertaking results in specific types of crashes involving these drivers. Four types of crashes were identified including crashes at intersections, rear end, crashes resulting from passing maneuvers and single vehicle crashes. For all crashes a general trend of decreasing involvement with increasing age was observed indicating that inexperience is the largest single contributor to the increased crash rates of younger drivers. Increasing the level of awareness among young drivers about these issues and their likely crash involvement seems to be the only viable approach.

The two-source method was used to measure the bulk properties (complex characteristic impedance and complex wavenumber) of sound-absorbing materials, and results were compared to those obtained with the more commonly used two-cavity method. The results indicated that the two-source method is superior to the two-cavity method for materials having low absorption. Several applications using bulk properties are then presented. These include: (1) predicting the absorptive properties of an arbitrary thickness absorbing material or (2) layered material and (3) using bulk properties for a multi-domain boundary element analysis.

The principle of vibro-acoustic reciprocity is reviewed and applied to model sound radiation from a shaker excited structure. Transfer functions between sound pressure at a point in the far field and the velocity of a patch were determined reciprocally both for the to-scale structure and also for a half-scale model. A point monopole source was developed and utilized for the reciprocal measurements. In order to reduce the measurement effort, the boundary element method (BEM) was used to determine the reciprocal transfer functions as an alternative to measurement. Acceleration and sound intensity were measured on patches of the vibrating structure. Reciprocally measured or BEM generated transfer functions were then used to predict the sound pressure in the far field from the vibrating structure. The predicted sound pressure compared favorably with that measured.

This paper presents a stability analysis of the free-piston Stirling engine and linear alternator power generation system. Since such a system operates under sustained mechanical oscillations, stability of the system is important for proper operation, and as a criterion in selecting the tuning capacitor. The stability criterion of the system is that the rate of change in power dissipation and electric power output is always faster than the rate of the power generated by the engine. The dynamic equations and model of the system are developed in this paper. Frequency domain analysis and Bode plot techniques are utilized in the study. The stable operating frequency region corresponding to different levels of power output are then determined.

This paper presents the criteria in selecting the size of the tuning capacitor, and the cost tradeoff between magnet volume and tuning capacitor in a free piston Stirling engine power generation system. The permissible range of capacitor size corresponding to different magnet volume, in order to prevent magnet demagnetization and stabilize the operation of the system, is determined. Within the permissible range suitable capacitor size may be selected to compensate the inductive load of the system to improve the overall power factor. If the capacitor size is not in the permissible range, there would exists a danger of losing magnet strength, or unstable operation of the engine that would destroy the engine due to unbounded amplitude of piston oscillations. The theory developed is then applied to a practical system, and the cost tradeoff between magnet volume and capacitor is studied.

System modeling and simulation results for an experimental switched reluctance external integral starter/generator (EISG) are reported. The EISG system employs a single switched reluctance machine and a generating system architecture that produces two separate 270 Vdc buses from that single switched reluctance machine. The machine has six phases with three of the phases connected to one converter supplying 125 kW to one 270 Vdc bus while the other three phases are connected to a second converter supplying 125 kW to the other 270 Vdc bus. Each bus has its own EMI filter and control in addition to its own converter. Two separate system models have been developed for the EISG. One of these models has been denoted the averaged model and the other has been denoted the detailed model. Both models include the switched reluctance machine and power electronics, the EMI filter, and the feedback control. The development of both of these models is described.

This paper examines the feasibility of using the boundary element method (BEM) and the Rayleigh integral to assess the sound radiation from engine components such as oil pans. Two oil pans, one cast aluminum and the other stamped steel, are used in the study. All numerical results are compared to running engine data obtained for each of these oil pans on a Cummins engine. Measured running-engine surface velocity data are used as input to the BEM calculations. The BEM models of the oil pains are baffled in various ways to determine the feasibility of analyzing the sound radiated from the oil pan in isolation of the engine. Two baffling conditions are considered: an infinite baffle in which the edge of the oil pan are attached to an infinite, flat surface; and a closed baffle in which the edge of the oil pan is sealed with a rigid structure. It is shown that either of these methods gives satisfactory results when compared to experiment.

Carbon nanomaterials such as vertically aligned carbon nanotubes arrays are emerging new materials that have demonstrated superior mechanical, thermal, and electrical properties. The carbon nanomaterials have the huge potential for a wide range of vehicular applications, including lightweight and multifunctional composites, high-efficiency batteries and ultracapacitors, durable thermal coatings, etc. In order to design the carbon nanomaterials for various applications, it is very important to develop effective computational methods to model such materials and structures. The present work presents a structural mechanics approach to effectively model the mechanical behavior of vertically aligned carbon nanotube arrays. The carbon nanotube may be viewed as a geometrical space frame structure with primary bonds between any two neighboring atoms and thus can be modeled using three-dimensional beam elements.

Numerical acoustics has traditionally been relegated to a prediction only role. However, recent work has shown that numerical acoustics techniques can be used to diagnose noise problems. The starting point for these techniques is the acoustic transfer vector (ATV). First of all, ATV's can be used to conduct contribution analyses which can assess which parts of a machine are the predominant noise sources. As an example, the sound power contribution and radiation efficiency from parts of a running diesel engine are presented in this paper. Additionally, ATV's can be used to reliably reconstruct the vibration on a machine surface. This procedure, commonly called inverse numerical acoustics (INA), utilizes measured sound pressures along with ATV's to reconstruct the surface velocity. The procedure is demonstrated on an engine cover for which the reconstructed vibration had excellent agreement with experimental results.

An advanced computational method is presented for calculating the sound radiated by vibrating engine of arbitrary shape. The method is based on the numerical evaluation of the Helmholtz Integral Equation. In particular an isoparametric element formulation is introduced in which both the surface geometry and the acoustic variables on the surface of the vibrating body are represented by second order shape functions within the local coordinate system. The formulation includes the case where the surface may have a non-unique normal (e.g. at edges or corners). A general result for the surface and field velocity potential is derived. Test cases involving spherical geometry are given for a pulsating sphere and for an oscillating sphere in which the analytical solutions are known. Examples for bodies with edges and corners are shown for the problems of radiation from a circular cylinder and from a pulsating cube.

In many industries, muffler and silencer design is primarily accomplished via trial and error. Prototypes are developed and tested, or numerical simulation (finite or boundary element analysis) is used to assess the performance. While these approaches reliably determine the transmission loss, designers often do not understand why their changes improve or degrade the muffler performance. Analyses are time consuming and models cannot be changed without some effort. The intent of the current work is to demonstrate how plane wave muffler models can be used in industry. It is first demonstrated that plane wave models can reliably determine the transmission loss for complicated mufflers below the cutoff frequency. Some tips for developing dependable plane wave models are summarized. Moreover, it is shown that plane wave models used correctly help designers develop intuition and a better understanding of the effect of their design changes.