Search Results

This paper covers the mathematical modeling of governing equations for the coupled heat and mass transfer phenomena during adsorption and desorption. Also the main focus is given on the methodology for numerical simulation for solving these partial differential equations for carbon canister. A comprehensive literature review is presented to summarize the target requirements of allowed evaporative emission level of gasoline vapour in grams per day based on global standards like, EU6, EPA stage II enhanced, CARB LEVII, PZEV and SULEV. In order to meet these stringent emission norms, presence of carbon canister is mandatory. The simulation results are compared for the gasoline vehicle application at various climatic temperature conditions in India, in which the canister sizing vs allowable emission targets are summarized.

Vehicles consume energy and release harmful emissions throughout their life period from the manufacturing stage of raw materials to the vehicle scrapyard. The current Green-House Gas (GHG) emissions from diesel and petrol vehicles are reported to be 164 g CO2/km and 156 g CO2/km respectively. Thus, enormous research studies are been carried out for low-carbon alternative fuel-powered vehicles to reduce the overall GHG emissions. Numerous research on hydrogen as a transportation fuel has demonstrated the potential of reduced vehicular emissions compared to conventional fuels. Life cycle assessment (LCA) is a comprehensive methodology used for estimating the overall environmental impact of vehicles. In this present work, a comparative LCA is conducted between Compressed Natural gas (CNG) powered vehicles and H-CNG powered vehicles. The effect of the two alternative vehicles is assessed from various points in their lifetime using the GREET model software.

The objective of the research is to develop a lightweight yet stiff, 2 piston fixed brake caliper which can be used in formula student race car. To make a race car, its components need to be lighter. To stop a car with minimum stopping distance, it needs to have a sophisticated braking system with well-designed components. The designing of the caliper is carried out on the Altair Inspire software. The topology optimisation algorithm is used to minimise the weight of the caliper without compromising the stiffness. The structural analysis is also carried out on the Altair Inspire. The caliper is also tested for fatigue failure using Ansys.

The major challenge that is faced by most of the engine manufacturers nowadays is to meet the stringent emission norms with least modification in the engine design. In achieving the emission norms simplicity of the design has to be maintained as far as possible by optimizing the available emission control techniques. This paper deals with such optimal technique with reduced cost and up gradation of the engine from CPCB I to CPCB II in minimum time with minimum design changes. This difficult task is achieved by adopting direct continuous EGR and intercooler with appropriate injection timing and optimizing the fuel injection pump in a cost effective manner. The experiment is carried out on 2.86 litre turbocharged engine giving power output 44.5 kW @1500 rpm. In order to achieve the NOx emission norms LLR FIP is used, to retard the injection timing at part loads to reduce the in-cylinder temperature.

The cross flow design of a radiator and its heat transfer and temperature drop was simulated then validated by using a data acquisition system during both static and dynamic running conditions of a Formula SAE car. The data acquisition system simulated and validated the radiator's cross flow design and heat transfer, as well as the temperature drop, under static and dynamic conditions in a car. The optimal radiator design determines the engine's operating temperature and the desired temperature drop gain through proper design of the inner core, number of fins and tubes, and radiator material. The purpose of a properly designed radiator is to prevent the combustion engine from heating up above its operating temperature [1]. The radiator's design is based on the operating temperature of the CBR 600RR engine. The highest temperature recorded was around 105°C, and in the worst case scenario, it can reach 110°C.

The present study discusses the effects of engine combustion, performance and emission features of methanol-gasoline blend fired lean burn Spark Ignition (SI) engine. Performance features such as Brake Power (BP), Brake Specific Fuel Consumption (BSFC), Brake Thermal Efficiency (BTE), tail pipe emissions namely Hydrocarbon (HC), Carbon Monoxide (CO), Nitrogen Oxide (NO), Carbon di Oxide (CO2) and combustion characteristics viz. in-cylinder pressure, Heat Release Rate (HRR), Cumulative Heat Release (CHR) and variation of mean effective pressure were measured and compared with that of neat gasoline. Experiments were conducted on a modified sole cylinder four-stroke compression engine (Kirloskar TAF1) to operate as SI engine with a compression ratio of 10.5:1. A new manifold injection system and ignition system were developed by replacing the fuel injection pump and injector.

Epoxy carbon fiber composite materials are known for their light weight and high performance. They can be effective substitutes for commonly used materials for making drive shafts. Fiber orientation angle plays a major role in determining such a drive shaft’s responses. The responses considered in this paper are critical buckling torque, fundamental natural frequency and total deformation. A drive shaft made of epoxy carbon unidirectional prepreg is generated using ANSYS 18.0 ACP Composite Prepost. The objective of this paper is to determine an optimal configuration of fiber orientation angles for four, five and six-layered epoxy carbon drive shaft which tends to increase critical buckling torque and fundamental natural frequency while decreasing the total deformation. The optimal configuration which satisfies this objective for the three responses is identified by Minitab 17 statistical software.

This paper summarizes the research work incorporated in the exploration of the potential of swirling in CI Engine and designing of a new mechanism, particularly at inlet, to deliver it to improve the in-cylinder air characteristics to eventually improve mixing and combustion process to improve the engine performance. The research is concentrated on the measures to be done on engine geometry so as to not only deliver advantage to any specific fuel. According to the CI combustion theory, better engine performance may be achieved with Higher Viscous Fuel by improving the in-cylinder air-fuel mixing by increasing the swirl (rotation of air view from top of the cylinder) and tumble (rotation of air view from front of the cylinder) of in-cylinder air inside the fuel-injected region. The proposed inlet component is embedded with airfoil and is suitably designed after being iterated from four steps.

This paper describes the modelling and electromagnetic analysis of Permanent Magnet Brushed Direct Current (PMBDC) motor using Finite Element Analysis (FEA) software packages. The designed motors referred in this analysis are fit for use in applications of the electronic throttle control and exhaust gas recirculation in automobiles. Performances of the designed PMBDC models are compared with the traditionally used machines. Three PMBDC models with different operating characteristics are proposed for the two applications. Each model is suitable for use in both applications. Cost analysis of the motors is also carried out, and comparison with the traditionally used machines is done.

Considerable weight of an automobile is constituted by the engine and there is scope for improvement in fuel efficiency and emission control through optimization of weight in the engine. In this work, AlSi10Mg alloy produced by the direct metal laser sintering (DMLS) is suggested for engine application which is a lightweight aluminum alloy. Mechanical properties like tensile strength, compressive strength, and hardness of both cast and DMLS manufactured alloy are compared followed by analysis of SEM images of tensile test fractured surfaces. Reciprocating wear test is carried out for one lakh cycles at 125°C temperature with SAE 40 grade oil as lubricant. Co-efficient of friction (COF), wear rate of the cast and DMLS manufactured samples are compared. Wear patterns are analyzed using SEM images of the wear tracks.

Various research regarding new types of fabrication and modifications of Aluminium alloy to improve the existing properties are going on. The wide range application of aluminium alloy is in aerospace and Automobile Industries. The demand for this material improved by mechanical properties with little to zero increment in weight. The current work is based on the fabrication of hybrid aluminium metal matrix composites with the addition of TiC (Titanium Carbide) and Al2O3 (Aluminium Oxide) reinforcement particle using stir casting technique. Three types of hybrid composite samples were prepared based on the weight percentage 5% Al2O3+0% TiC (sample-1), 8% Al2O3 + 12% TiC (sample-2), 20% Al2O3+15% TiC (sample-3). The objective of the study is to analyze the mechanical and corrosion properties of the hybrid composite with the influence of the reinforcement and varying the weight fraction of the particles.

In lieu of the drastic growth of the vehicle population, there is a huge consumption of fossil fuels and mineral oils for mobility. This leads to depletion in fossil fuels and mineral oils which are the by-products of petroleum. These fossil fuels can’t sustain for a long period of time because of its toxicity. In order to reduce the usage of existing mineral oil for lubrication, a source of non-edible oil from Jatropha curcus is processed as jatropha methyl ester (JME). It is holding high viscosity, density and easy blend with base oil. In this current work, the wear resistance of the lubricating oil is enhanced by the addition of nano-copper oxide particle blend with the base oil. The emission performance and tribological behavior have been experimentally tested in 98.2CC two-stroke air cooled engine. The 20% of JME blend with CuO nano particle provides better emission performance and wear characteristics than the other combination of blends.

Inconel 625, nickel based alloy, is found in gas turbine blades, seals, rings, shafts, and turbine disks. On the other hand, the manufacturing of this alloy is challenging, mainly when machining processes are used due to excellent mechanical properties. Application of nanofluids in minimum quantity lubrication (MQL) shows gaining importance in the machining process, which is economical and eco-friendly. The principal objective of this investigational work is to study the influence of three types of nanofluids in the MQL turning of Inconel 625 nickel based alloys. The used nanofluids are multi-walled carbon nanotubes (CNT), alumina (Al2O3) and copper oxide (CUO) dispersed in vegetable oil. Taguchi-based L27 orthogonal array is used for the experimental design. The parameter optimization of design variables over response is carried out by the use of Taguchi-based derringer's desirability function.

The present study was carried out to analyze the catalytic action of K2O-Al2O3 in NOx Storage and Reduction (NSR) monolith catalyst and Fe2O3-TiO2 in Selective Catalytic Reduction (SCR) monolith catalyst. The core objective of this investigation is to determine the maximum percentage of Oxides of Nitrogen (NOx) reduction in NSR and NSR-SCR combined system with respect to engine exhaust gas temperature and compares the results with the results of the conventional mode of operation. To accomplish this task monolith ceramic bricks were coated with K2O-Al2O3 (NSR) and Fe2O3-TiO2 (SCR) catalyst and were placed in different configurations inside the catalytic chamber. Several trials were attempted to get the optimal operating temperature that has a maximum NOx removal efficiency when successively connecting a single NSR catalyst and the combined NSR-SCR double bed catalyst. Single NSR monolith at 320 °C, showed the best NOx conversion rate of 74%.

Nimonic 90A alloy is a nickel-chromium-cobalt alloy and found as a potential material for turbine blades, discs, forgings, a ring section, and hot-working tools. This paper presents the effect of concentration along with cutting speed and feed rate on Fz: cutting force, Ra: surface roughness and Vba: tool wear with the application of two different nanofluids (NFS) on turning of Nimonic 90A by TiAlN PVD carbide cutting inserts. The nanoparticles suspended in oil taken for present investigation are nAl2O3, nCNT, and groundnut oil. The Taguchi L9 orthogonal array and derringer’s desirability response surface has been employed for parameter design and optimal search. 3D surface plots, factor effect plots, Taguchi S/N, and variance tests are used to study the effect of concentration on the machining performance of Nimonic 90A. The statistical analysis revealed % concentration for nCNT and cutting speed for nAl2O3 are found as an influenced parameter on performance characteristics.

The objective of this study is to develop, demonstrate and validate the methodology of external aerodynamic analysis of a State Road Transport bus for prediction of drag coefficient and its impact on fuel consumption with experimental validation. It has been verified that vehicle consumes around 40% of the available engine power to overcome the air drag. This gives us a huge scope to study the effect of aerodynamic drag. Baseline model of State Road Transport Bus was evaluated for estimating fuel consumption using Computational Fluid dynamics (CFD) methodology. The CFD results were validated with the experimental data with less than 10% deviation. Bus design was optimized with an objective of reducing the fuel consumption with parameters like angle of windshield, rounding and tapering corners and rear draft angle. Optimized bus design is also ensured to meet functional specifications as per AIS052.

The surface properties have a vital role in the overall performance of the parts like brake shoe pad and other frame system. The mechanical and residual stress measurements of aluminium alloy 5083 were investigated on friction stir processed plates using the reinforcements of chromium oxide (Cr2O3) and titanium dioxide (TiO2) separately as well as combination of these powders. A comparative study was made to analyze the effects of reinforcements, tool type (cylindrical and threaded), parameters and the volume fraction of the reinforcements. The mechanical properties such as surface hardness and residual stress of the friction stir processed specimens were investigated. The experimental results shows that there was a significant increase in surface hardness (118 HRC) as well as a decrease in residual stress compare to the base metal. This study also reveals that the threaded tool with a reinforcement of Cr2O3 and TiO2 reflected better mechanical properties than the cylindrical tool.

Permanent magnet brushed DC (PMBDC) motors are mostly preferred in many automotive applications because of better power density and easier control. Five different automotive applications such as electric parking brake (EPB), power seat, power window, sunroof drive, and tire air pump are chosen and discussed in this paper. A step-by-step electromagnetic analysis is carried out for all the designed models. Low-cost ferrite-based magnets are used for cost reduction keeping the efficiency as high above 77% in all the models. Comparison on performance and cost are discussed in the conclusion section.

An “APU” (Auxiliary Power Unit) is a small gas turbine engine to provide supplementary power to an aircraft and is located at the tails of larger jets. APU generators provide auxiliary electrical power for running aircraft systems on the ground. Applications include powering environmental systems for pre-cooling or preheating the cabin, and providing power for crew functions such as preflight, cabin cleanup, and galley (kitchen) operation and long-haul airliners must be started using pneumatic power of APU compressor. The Honeywell 131-9A gas turbine APU has 440 kW shaft power and 90 kW electric generator consuming 120 kg fuel/hour. Hybrid power systems based on fuel cells are promising technology for the forthcoming power generation market. A solid oxide fuel cell (SOFC) is the perfect candidate for utilizing waste heat recovery. This case deals with waste heat recovery from fuel cell exhaust using Brayton cycle as bottoming cycle for additional power production.

This paper presents a methodology for predicting thermal comfort inside Midibus cabin with an objective to modify the Heating, Ventilation and Air Conditioning (HVAC) duct design and parametric optimization in order to have improved thermal comfort of occupant. For this purpose the bus cavity is extracted from baseline CAD model including fully seated manikins with various seating positions. Solar Load has been considered in the computational model and passenger heat load is considered as per BSR/ASHRAE 55-1992R standard. CFD simulation predicted the air temperature and velocity distribution inside passenger cabin of the baseline model. The experimental measurements have been carried out as per the guidelines set in APTA-BT-RP-003-07 standard. The results obtained from CFD and Experimental test were analysed as per EVS EN ISO7730 standard and calculated occupant comfort in terms of thermal comfort parameters like Predicted Mean Vote (PMV) and Predicted Percentage Dissatisfied (PPD).