Search Results

In recent years a new combustion phenomenon called Low-Speed Pre-Ignition (LSPI) occurred, which is the most important limiting factor to exploit further downsizing potential due to the associated peak pressures and thus the huge damage potential. In the past there were already several triggers for pre-ignitions identified, whereat engine oil seems to have an important influence. Other studies have reported that detached oil droplets from the piston crevice volume lead to auto-ignition prior to spark ignition. However, wall wetting and subsequently oil dilution and changes in the oil properties by impinging fuel on the cylinder wall seem to have a significant influence in terms of accumulation and detachment of oil-fuel droplets in the combustion chamber. For this reason, the influence of test fuels with different volatility were investigated in order to verify their influence on wall wetting, detachment and pre-ignition tendency.

The objective of the project was to compare the exhaust gas emissions and fuel consumption of a test vehicle, which was on a one hand operating with premium gasoline 95 RON (RON 95) and a mixture of 90% by volume premium gasoline 95 RON and 10% by volume of high purity bio ethanol (E10) on the other hand. As a test vehicle a Skoda Octavia station wagon was used. The engine of the tested vehicle corresponded to the Euro 4 emission standard. The investigations were conducted under the real world conditions, and also at the chassis dynamometer test bench. The tested vehicle was equipped with a new On-board measurement System (OBM) to determine the mass emissions on real world driving routes. The measurement method is based on modal analysis of the emission concentrations in the tailpipe of the vehicle, and real time exhaust mass flow determination.

The piston ring and cylinder liner tribosystem is very sensitive. It is a heavily loaded system with high temperature and force exposure. High demands are made on the components in this area. These facts concern not only system components, but also the engine oil which can reach up to 300°C at the inner cylinder walls. High temperatures and force cause oil aging. As a part of the combustion chamber, the piston ring-cylinder liner tribosystem is in close contact with combustion constituents. If alternative fuels like ethanol are used, the influences to this tribosystem have to be investigated. In particular, the impacts of oil aging have to be considered to avoid higher wear and damage to the engine, to assure low fuel consumption, and to extend oil change intervals. Research work on abrasion of the ring-cylinder system was aimed to gain detailed information about the effects on this tribosystem.

Current commercial vehicles' engines are complex systems with multiple degrees of freedom. In conjunction with current emissions regulations manufacturers are forced to combine highly developed engines with complex aftertreatment systems. A comprehensive simulation model including the engine and aftertreatment system has been set up in order to study and optimize the overall system. The model uses a phenomenological spray combustion model to predict fuel consumption and NO emissions. In addition physical models for the material temperatures and the reaction kinetics were generated for the aftertreatment system. Steady state and transient measurements were used to calibrate the engine as well as the aftertreatment model. The aim for a system-level optimization was a reduction of fuel consumption while meeting emission standards.

The usage of ethanol and two different mixtures of ethanol and gasoline (E85 and E65) wаs investigated on a modified diesel engine designed to work in a dual-fuel combustion mode with intake manifold alcohol injection. The maximum ratio of alcohol to diesel fuel was limited by irregular combustion phenomena like degrading combustion quality and poor process controllability at low load and knock as well as auto-ignition at high load. With rising alcohol amount, a significant reduction of soot mass and particle number was observed. At some testing points, substituting diesel with ethanol, E65 or E85 led to a reduction of NOx emissions; however, the real benefit concerning the nitrogen oxides was introduced by the mitigation of the soot-NOx trade-off. The indicated engine efficiency in dual-fuel mode showed an extended tolerance against high EGR rates. It was significantly improved with enhanced substitution ratios at high loads, whereas it dropped at low loads.

A fast preparation of the liquid urea water solution (UWS) is necessary to ensure high conversion rates in exhaust aftertreatment systems based on Selective Catalytic Reduction (SCR). Droplet wall interaction is of major importance during this process, in particular droplet breakup and the Leidenfrost effect. A deeper understanding of the underlying mechanisms is a basic requirement to calibrate CFD models in order to improve their prediction accuracy. This paper presents a detailed literature study and discussion about the major impact factors on droplet wall interaction. Measurements of the Leidenfrost temperature were conducted and the corresponding regimes classified based on optical observations. The pre- and post-impingement spray was analysed using the laser diffraction method. Further, the validity of spray initialisation based on measurements at room temperature was verified.

A naturally aspirated SI engine with port fuel injection was investigated at the Institute for Powertrains and Automotive Technology of the Vienna University of Technology to analyze the impact of the ethanol blend E85 on the full load performance. Measurements and numerical studies with a predictive wall film model have been carried out to explain the mixture cooling, the calorific fluid properties after inlet valve closing and the volumetric efficiency with conventional fuel and E85. It could be shown that only with a detailed modelling of the wall film formation in the inlet port an accurate prediction of the engine's full load performance is possible when studying different fuels with varying fluid properties. Anyway, an integrated approach that includes measurements and numerical investigations is necessary to analyse the mixture preparation and the engine process correctly.