Search Results

It was demonstrated that a bypass duct similar to a Herschel- Quincke tube could be used to increase the transmission loss of mufflers at selected frequencies. In many cases, the duct can be short and thought of as a leak. It was shown that the optimal length and cross-sectional area could be determined by using a simple optimization technique known as the Vincent Circle. Most importantly, it was demonstrated that the attenuation at low frequencies could be improved by as much as 15 dB. To prove the concept, a muffler was designed and optimized using transfer matrix theory. Then, the optimized muffler was constructed and the transmission loss measured using the two-load method. The measured results compared well with prediction from transfer matrix theory. Boundary element simulation was then used to further study the attenuation mechanism.

Transmission loss (TL) is a good performance measure of mufflers since it represents the muffler's inherent capability of sound attenuation. There are several existing numerical methods, which have been widely used to calculate the TL from numerical simulation results, such as the four-pole and three-point methods. In this paper, a new approach is proposed to evaluate the transmission loss based on the reciprocal work identity. The proposed method does not assume plane wave propagation in the inlet and outlet ducts, and more importantly, does not explicitly apply the anechoic termination impedance at the outlet. As a result, it has the potential of extending TL computation above the plane wave cut-off frequency.

The two-load method is used to measure the transmission loss of thin panels in two different sized impedance tubes (3.49 cm and 10.16 cm). Samples were initially tested with a clamped boundary condition. This was followed by tests with an elastomer inserted between the tube and tested sample to adjust the boundary condition at the periphery. In all tests performed, the influence of the sample holding method could not be removed from the test. The measured transmission loss was compared to finite element simulation with good agreement for both impedance tubes. Additionally, the effect of a compliant boundary condition along the periphery of the sample was also validated via simulation.

Transmissibility is the most common metric used for isolator characterization. However, engineers are becoming increasingly concerned about energy transmission through an isolator at high frequencies and how the compliance of the machine and foundation factor into the performance. In this paper, the transfer matrix approach for isolator characterization is first reviewed. Two methods are detailed for determining the transfer matrix of an isolator using finite element simulation. This is accomplished by determining either the mobility or impedance matrix for the isolator and then converting to a transfer matrix. It is shown that results are similar using either approach. In both cases, the isolator is first pre-loaded before the transfer matrix is determined. The approach to find isolator insertion loss is demonstrated for an isolator between two plates, and the effect of making changes to the structural impedance on the machine side of the isolator by adding ribs is examined.

A recently developed superposition approach for determining the insertion loss of a two-inlet muffler is reviewed. To validate the approach, calculated and measured insertion losses are compared for a small engine muffler with two inlets and one outlet. After which, the phasing between the two inputs is varied and the insertion loss is evaluated. Results show that the insertion loss is strongly affected by the phasing between sources at low frequencies while phasing between sources has a lesser impact at high frequencies. At the conclusion of the paper, the theory for applying the superposition approach to transmission loss is reviewed.

Diesel engines produce harmful exhaust emissions and high exhaust noise levels. One way of mitigating both exhaust emissions and noise is via the use of after treatment devices such as Catalytic Converters (CC), Selective Catalytic Reducers (SCR), Diesel Oxidation Catalysts (DOC), and Diesel Particulate Filters (DPF). The objective of this investigation is to characterize and simulate the acoustic performance of different types of filters so that maximum benefit can be achieved. A number of after treatment device configurations for trucks were selected and measured. A measurement campaign was conducted to characterize the two-port transfer matrix of these devices. The simulation was performed using the two-port theory where the two-port models are limited to the plane wave range in the filter cavity.

A process for predicting the transmission and insertion losses of multi-component exhaust systems is detailed in this paper. A two-tiered process incorporating boundary element analysis to evaluate multi-component systems is implemented. At the component level, the boundary element method is used to predict the transfer matrix for larger components where plane wave behavior is not expected within the component. The transfer matrix approach is then used to predict insertion loss for built-up systems with interconnecting duct or pipe work. This approach assumes plane wave behavior at the inlet and outlet of each component so it is limited to the low frequency regime. Results are compared with experimental results for HVAC systems.

This paper documents an inverse visible element Rayleigh integral (VERI) approach. The VERI is a fast though approximate method for predicting sound radiation that can be used in the place of the boundary element method. This paper extends the method by applying it to the inverse problem where the VERI is used to generate the acoustic transfer matrix relating the velocity on the surface to measurement points. Given measured pressures, the inverse VERI can be used to reconstruct the vibration of a radiating surface. Results from an engine cover and diesel engine indicate that the method can be used to reliably quantify the sound power and also approximate directivity.

This paper explores the use of inverse numerical acoustics to reconstruct the surface vibration of a noise source. Inverse numerical acoustics is mainly used for source identification. This approach uses the measured sound pressure at a set of field points and the Helmholtz integral equation to reconstruct the normal surface velocity. The number of sound pressure measurements is considerably less than the number of surface vibration nodes. A brief guideline on choosing the number and location of the field points to provide an acceptable reproduction of the surface vibration is presented. The effect of adding a few measured velocities to improve the accuracy will also be discussed. Other practical considerations such as the shape of the field point mesh and effect of experimental errors on reconstruction accuracy will be presented. Examples will include a diesel engine and a transmission housing.

Insertion loss in one-third or octave bands is widely used in industry to assess the performance of large silencers and mufflers. However, there is no standard procedure for determining the transmission loss in one-third or octave bands using measured data or simulation. In this paper, assuming that the source is broadband, three different approaches to convert the narrowband transmission loss data into one-third and octave bands are investigated. Each method is described in detail. To validate the three different approaches, narrowband transmission loss data of a simple expansion chamber and a large bar silencer is converted into one-third and octave bands, and results obtained from the three approaches are demonstrated to agree well with one another.

This paper documents a finite element approach to predict the attenuation of muffler and silencer systems that incorporate diesel particulate filters (DPF). Two finite element models were developed. The first is a micro FEM model, where a subset of channels is modeled and transmission matrices are determined in a manner consistent with prior published work by Allam and Åbom. Flow effects are considered at the inlet and outlet to the DPF as well as viscous effects in the channels themselves. The results are then used in a macro FEM model of the exhaust system where the transmission relationship from the micro-model is used to simulate the DPF. The modeling approach was validated experimentally on an example in which the plane wave cutoff frequency was exceeded in the chambers upstream and downstream to the DPF.

This paper explores the use of inverse boundary element method to identify aeroacoustic noise sources. In the proposed approach, sound pressure at a few locations out of the flow field is measured, followed by the reconstruction of acoustic particle velocity on the surface where the noise is generated. Using this reconstructed acoustic particle velocity, the acoustic response anywhere in the field, including in the flow field, can be predicted. This approach is advantageous since only a small number of measurement points are needed and can be done outside of the flow field, and a relatively fast computational time. As an example, a prediction of vortex shedding noise from a circular cylinder is presented.

Numerical acoustics has traditionally been relegated to a prediction only role. However, recent work has shown that numerical acoustics techniques can be used to diagnose noise problems. The starting point for these techniques is the acoustic transfer vector (ATV). First of all, ATV's can be used to conduct contribution analyses which can assess which parts of a machine are the predominant noise sources. As an example, the sound power contribution and radiation efficiency from parts of a running diesel engine are presented in this paper. Additionally, ATV's can be used to reliably reconstruct the vibration on a machine surface. This procedure, commonly called inverse numerical acoustics (INA), utilizes measured sound pressures along with ATV's to reconstruct the surface velocity. The procedure is demonstrated on an engine cover for which the reconstructed vibration had excellent agreement with experimental results.

The theory of patch (or panel) contribution analysis is first reviewed and then applied to a motorcycle engine on a test stand. The approach is used to predict the sound pressure in the far field and the contribution from different engine components to the sound pressure at a point. First, the engine is divided into a number of patches. The transfer functions between the sound pressure in the field and the volume velocity of each patch were determined by taking advantage of vibro-acoustic reciprocity. An inexpensive monopole source is placed at the receiver point and the sound pressure is measured at the center of each patch. With the engine idling, a p-u probe was used to measure particle velocity and sound intensity simultaneously on each patch. The contribution from each patch to the target point is the multiplication of the transfer function and the volume velocity, which can be calculated from particle velocity or sound intensity. There were two target points considered.

Transfer path analysis is commonly used to determine input forces indirectly utilizing measured responses and transfer functions. Though it is recommended that the source should be detached from the vibrating structure when measuring transfer functions, engineers and technicians frequently have a difficult time in doing so in practice. Recently, a substitute for inverse force determination via transfer path analysis has been suggested. The indirectly determined forces are termed blocked forces and are usable so long as the source and machine are not detached from one another. Blocked forces have the added advantage of being valid even if the machine structure is modified. In this research, a typical automotive engine cover is considered as a receiver structure and is bolted to a plastic source plate excited by an electromagnetic shaker.

Bench tests are an important step to developing mufflers that perform adequately with acceptable pressure drop. Though the transmission loss of a muffler without flow is relatively simple to obtain using the two-load method, the presence of mean flow modifies the muffler behavior. The development of an insertion loss test rig is detailed. A blower produces the flow, and a silencer quiets the flow. Acoustic excitation is provided by a loudspeaker cluster right before the test muffler. The measurement platform allows for the measurement of flow-induced noise in the muffler. Also, the insertion loss of the muffler can be determined, and this capability was validated by comparison to a one-dimensional plane wave model.

The two-load method is commonly applied to determine the transmission loss for a muffler especially if an impedance tube rig is used. Although one procedure and algorithm is detailed in ASTM E2611, the quality of the transmission loss curve is dependent on several factors that are not discussed in detail in the standard. In this paper, several practical concerns are investigated including (1) the number of channels used in the measurement, (2) the selection of the reference channel, and (3) the choice of data processing algorithm (transfer or scattering matrix). Results are compared for a simple expansion chamber first, then for mufflers of other types. Recommendations are made for obtaining smoother transmission loss curves for various measurement methods.

The two-load method is commonly used to determine the transmission loss of a muffler or silencer. Several practical measurement considerations are examined in this paper. First of all, conical adapters are sometimes used to transition between impedance tubes and the muffler. It is demonstrated that the effect of adding the adapter can be quite significant at low frequencies especially if the adapter is short in length. The effect of changing the length of the adapter was examined via measurement and plane wave theory. Secondly, the effect of selecting the reference microphone was examined experimentally. It was found that measurements are improved by selecting a downstream reference. Finally, the effect of using different frequency response function estimation algorithms (H1, H2 and Hv) was compared sans flow. This had little effect on the measurement.

Prior research on assessing multiple inlet and outlet mufflers is limited, and only recently have researchers begun to consider suitable metrics for multiple inlet and outlet mufflers. In this paper, transmission loss and insertion loss are defined for multiple inlet and outlet mufflers using a superposition method that can be extended to any m-inlet n-outlet muffler. Transmission loss is determined assuming that the sources and terminations are anechoic. On the other hand, insertion loss considers reflections. For both metrics, the amplitude and phase relationship between the sources should be known a priori. This paper explains both metrics, and measurement of transmission and insertion loss are demonstrated for a 2-inlet 2-outlet muffler with good agreement.