Search Results

The Detroit Diesel 6V-92TA engine has been redesigned to run on alcohol fuels to meet 1991 urban bus emission standards. A prototype engine was tested over the EPA transient procedure, using mixtures of methanol, ethanol (with and without water), gasoline, and ignition enhancer. Regulated and selected unregulated emissions were measured. Organic material hydrocarbon equivalent (OMHCE) emissions were significantly above the hydrocarbon emission standard; however, emissions of CO and NO, were below the 1991 emission standards for the fuel combinations used. Particulate emissions were close to the 1991 urban bus emission standard for some configurations. The method used for calculating OMHCE emissions when ethanol was used is also given.

Exhaust emissions from heavy-duty diesel engines operating at high altitude are of concern. EPA and Colorado Department of Health sponsored this project to characterize regulated and selected unregulated emissions from a naturally-aspirated Caterpillar 3208 and a turbocharged Cummins NTCC-350 diesel engine at both low altitude and simulated high attitude conditions (≈ 6000 ft). Emissions testing was performed over cold- and hot-start transient Heavy-Duty-Federal Test Procedure (HD-FTP) cycles as well as selected steady-state modes. In addition, the turbocharged engine was operated with mechanically variable and (fixed) retarded fuel injection timing to represent “normal” and “malfunction” conditions, respectively. High altitude operation generally reduced NOx emissions about 10 percent for both engines.

The use of a partial flow sampling system (PFSS) to measure nonroad steady-state diesel engine particulate matter (PM) emissions is a technique for certification approved by a number of regulatory agencies around the world including the US EPA. Recently, there have been proposals to change future nonroad tests to include testing over a nonroad transient cycle. PFSS units that can quantify PM over the transient cycle have also been discussed. The full flow constant volume sampling (CVS) technique has been the standard method for collecting PM under transient engine operation. It is expensive and requires large facilities as compared to a typical PFSS. Despite the need for a cheaper alternative to the CVS, there has been a concern regarding how well the PM measured using a PFSS compared to that measured by the CVS. In this study, three PFSS units, including AVL SPC, Horiba MDLT, and Sierra BG-2 were investigated in parallel with a full flow CVS.

Emissions from existing diesel-powered urban buses are increasingly scrutinized as local, state, and federal governments require enforcement of more stringent emission regulations and expectations. Currently, visual observation of high smoke levels from diesel-powered equipment is a popular indicator of potential emission problems requiring tune-up or engine maintenance. It is important that bus inspection and maintenance (I/M) operations have a quality control “test” to check engine emissions or diagnose the engine state-of-tune before or after maintenance. Ideally, the “emission test” would be correlated to EPA transient emissions standards, be of short duration, and be compatible with garage procedures and equipment. In support of developing a useful “short-test,” equipment was designed to collect samples of raw exhaust over a short time period for gaseous and particulate emissions.

Several diesel fuel properties have been identified as having significant effects on diesel engine emissions. For heavy-duty diesel engines, fuel properties of aromatics, back end volatility (represented by the 90 percent boiling point), and sulfur were examined in a previous CRC VE-1 study in which reductions in all three properties decreased regulated emissions to varying degrees. Aromatic levels and cetane numbers were generally correlated in the previous study, so variation in emissions due to “aromatics” could not clearly be assigned to variation in aromatic levels alone. To separate the effects of aromatics and cetane number, a fuel set with controlled variation in aromatics and cetane number was developed, including the use of ignition improver to increase the cetane number of selected fuels. The fuel set was used in a 1991 Prototype DDC Series 60 heavy-duty diesel engine to examine regulated emissions over EPA transient cycle operation.

Concern over emissions from heavy-duty diesel engines at high altitudes prompted an investigation into the effects of increasing altitude on gaseous and particulate emissions. On behalf of the Engine Manufacturers Association, emissions from a Detroit Diesel Corporation Series 60 at local test conditions (barometer 98.9 kPa), and two simulated altitudes, Denver (82.6 kPa) and Mexico City (77.9 kPa) were examined using a special altitude simulation CVS. Transient torque output and full load steady-state torque, for this turbocharged aftercooled engine, decreased slightly with increasing altitude. Although, the DDC Series 60 compensates for variation in barometer, transient composite emissions of HC, CO, CO2, smoke, and particulate matter generally increased with increasing altitude for both transient and steady-state operation.

A Coordinating Research Council sponsored test program was conducted to determine the effects of diesel fuel properties on emissions from two heavy-duty diesel engines designed to meet EPA emission requirements for 1994. Results for a prototype 1994 DDC Series 60 were reported in SAE Paper 941020. This paper reports the results from a prototype 1994 Navistar DTA-466 engine equipped with an exhaust catalyst. A set of ten fuels having specific variations in cetane number, aromatics, and oxygen were used to study effects of these fuel properties on emissions. Using glycol diether compounds as an oxygenated additive, selected diesel fuels were treated to obtain 2 and 4 mass percent oxygen. Cetane number was increased for selected fuels using a cetane improver. Emissions were measured during transient FTP operation of the Navistar engine tuned for a nominal 5 g/hp-hr NOx, then repeated using a 4 g/hp-hr NOx calibration.

As stringent emission regulations further constrain engine manufacturers by tightening both NOx and particulate emission limits, a knowledge of fuel effects becomes more important than ever. Among the fuel properties that affect heavy-duty diesel engine emissions, cetane number can be very important. Part of the CRC-APRAC VE-10 Project was developed to quantify the effects of cetane number on NOx and other emissions from a prototype 1998 Detroit Diesel Series 60. Three fuels with different natural cetane number (41, 45, 52) were treated with several levels and types of cetane improvers to study a range of cetane number from 40 to 60. Statistical analysis was used to define how regulated emissions from this prototype 1998 engine decreased with chemically-induced cetane number increase. Variation of HC, CO, NOx, and PM were modeled using a combination of a fuel's naturally-occurring cetane number and its total cetane number obtained with cetane improver.

Over twenty prototype hybrid buses and other commercial vehicles are currently being completed and deployed. These vehicles are primarily “series” hybrid vehicles which use electric motors for primary traction while internal combustion engines, or high-speed turbine engines connected to generators, supply some portion of the electric propulsion and battery recharge energy. Hybrid-electric vehicles have an electric energy storage system on board that influences the operation of the heat engine. The storage system design and level affect the vehicle emissions, electricity consumption, and fuel economy. Existing heavy-duty emissions test procedures require that the engine be tested over a transient cycle before it can be used in vehicles (over 26,000 lbs GVW). This paper describes current test procedures for assessing engine and vehicle emissions, and proposes techniques for evaluating engines used with hybrid-electric vehicle propulsion systems.

Emissions from two heavy-duty four stroke direct injection engines designed to use methanol fuel, one using Diesel pilot fuel injection and the other using spark ignition, were characterized in this program along with those from a comparably-sized Diesel engine. Emissions evaluated during both steady-state and transient FTP procedures included regulated gases (HC, CO, and NOx), unburned methanol, aldehydes, other gaseous organics, total particulate, sulfate, soluble organics in particulate and BaP. The engines adapted for methanol fuel and using catalysts emitted less HC, CO, particulate, soluble organics, and BaP than the Diesel fueled engine.

Emissions from a modern heavy-duty Diesel truck engine were characterized with five different fuels during transient and steady-state operation. A control fuel (Phillips D-2) was used for baseline emissions, and as base stock in three alternate fuel blends containing EDS or SRC-II middle distillates, or used lubricating oil. The fifth fuel tested was neat soybean oil, heated to 145°C. HC, CO, NOX, and particulate emissions were similar for this engine on all fuels tested, with the exception of higher particulates for the soybean oil and higher NOX for the SRC-II blend.

Diesel soot or smoke has been regarded as a nuisance pollutant and potential health hazard, especially in congested urban areas where diesel buses operate. Exhaust emissions from a DDAD 6V-71 coach engine and a similarly-powered 1980 GMC RTS-II coach, fitted with a non-catalyzed particulate trap, were characterized over various Federal Test Procedures for heavy-duty engines, including an experimental test cycle for buses. Regeneration was accomplished using an in-line burner in the exhaust to raise the engines' idle exhaust gas temperature from 120 to 700°C. Trap testing included approximately 15 hours of engine operation and 100 miles of bus operation. Particulate emissions were reduced by an average of 79 percent and smoke emissions were nil using the trap. The effect of the trap on regulated and other unregulated emissions was generally minimal.

Diesel engines are adjusted to manufacturers' specifications when produced and placed in service, but varying degrees of maintenance and wear can cause changes in engine performance and exhaust emissions. Maladjustments were made on two heavy-duty diesel engines typically used in buses in an effort to simulate some degree of wear and/or lack of maintenance. Emissions were characterized over steady-state and transient engine operation, in both baseline and maladjusted configurations. Selected maladjustments of the Cummins VTB-903 substantially increased HC, smoke and particulate emission levels. Maladjustments of the Detroit Diesel 6V-71 coach engine resulted in lower HC and NOX emission levels, but higher CO emissions, smoke, and particulate.

Three crude shale oils were chosen from six candidates to investigate their possible use as substitutes for No. 2 diesel fuel. Satisfactory hot engine operation was achieved on the crudes using a fuel heating system, allowing emissions characterization during transient and steady-state operation. Regulated gaseous emissions changed little with the crudes compared to diesel fuel; but total particulate and soluble organics increased, and larger injector tip deposits and piston crown erosion were observed. After engine rebuild, two minimally-processed shale oils were run without the fuel heating system, causing no engine problems. Most emissions were higher than for No. 2 fuel using an SO percent distillate of crude shale oil, but lower using a hydrotreated form of the distillate.

Regulated and some unregulated emissions from a Detroit Diesel Allison Division 8V-71TAC California bus engine were characterized over transient engine operation with and without catalyzed wire mesh particulate traps fitted in place of the standard exhaust manifold assemblies. Moderate reductions in particulate emissions were obtained, but initial trap design adversely affected performance of the 2-stroke, turbocharged, blower-scavenged bus engine. Most of the baseline engine performance was recovered with a second trap design. After catalyst aging, the second set of traps reduced baseline particulate emissions on both standard and low sulfur fuels by 60 and 70 percent, respectively.

The United States Environmental Protection Agency (EPA) has initiated Phase I of a regulatory program to control exhaust emissions of nonroad diesel engines over 37 kW. Central to any emissions regulation is the test procedure, which must include an appropriate test cycle. Based on actual in-use speed and estimated torque data collected from an agricultural tractor, a backhoe-loader, and a crawler tractor, three duty cycles were developed. Using an iterative process, comparison of chi-square statistical data was used to identify representative microtrips, segments of engine operation gathered during performance of selected activities. Representative microtrips for specific activities for a particular nonroad application were “strung” together to make up a test cycle. Before accepting the test cycle, data for the cycle was compared to statistical data used to characterize the raw data in an effort to validate that the cycle was representative of the raw data.