Search Results

The current trend toward more fuel efficient vehicles with lower emission levels has prompted development of new combustion techniques for use in gasoline engines. Stratified combustion has been shown to be a promising approach for increasing the fuel efficiency. However, this technique is hampered by drawbacks such as increased particulate and standard emissions. This study attempts to address the issues of increased emission levels by investigating the influence of high frequency ionizing ignition systems, 350 bar fuel injection pressure and various tumble levels on particulate emissions and combustion characteristics in an optical SGDI engine operated in stratified mode on isooctane. Tests were performed at one engine load of 2.63 bar BMEP and speed of 1200 rpm. Combustion was recorded with two high speed color cameras from bottom and side views using optical filters for OH and soot luminescence.

The potential of 48V Mild Hybrid is promising in meeting the present and future CO2 legislations. There are various system layouts for 48V hybrid system including P0, P1, P2. In this paper, P2 architecture is used to investigate the effects of water injection benefits in a mild hybrid system. Electrification of the conventional powertrain uses the benefits of an electric drive in the low load-low speed region where the conventional SI engine is least efficient and as the load demand increases the IC Engine is used in its more efficient operating region. Engine downsizing and forced induction trend is popular in the hybrid system architecture. However, the engine efficiency is limited by combustion knocking at higher loads thus ignition retard is used to avoid knocking and fuel enrichment becomes must to operate the engine at MBT (Maximum Brake Torque) timing; in turn neutralizing the benefits of fuel savings by electrification.

Cycle-resolved end-gas temperatures were measured using dual-broadband rotational CARS in a single-cylinder spark-ignition engine. Simultaneous cylinder pressure measurements were used as an indicator for knock and as input data to numerical calculations. The chemical processes in the end-gas have been analysed with a detailed kinetic mechanism for mixtures of iso-octane and n-heptane at different Research Octane Numbers (RON'S). The end-gas is modelled as a homogeneous reactor that is compressed or expanded by the piston movement and the flame propagation in the cylinder. The calculated temperatures are in agreement with the temperatures evaluated from CARS measurements. It is found that calculations with different RON'S of the fuel lead to different levels of radical concentrations in the end-gas. The apperance of the first stage of the autoignition process is marginally influenced by the RON, while the ignition delay of the second stage is increased with increasing RON.

The effects of multiple injections on engine-out emissions from a high-speed direct injection (HSDI) diesel engine were investigated in a series of experiments using a single cylinder research engine. Injection sequences in which the main injection was split into two, three and four pulses were tested and the resulting emissions (NOx, CO HC and particulate matter), torque and cylinder pressures were compared to those obtained with single injections. Together with the number of injections, the effects of varying the dwell time were also investigated. It was found that dividing the main injection into two parts lowered the engine-out particulate and CO emissions and increased fuel efficiency. However, it also resulted in increased NOx emissions.

Future demands for improvements in the fuel economy of gasoline passenger car engines will require the development and implementation of advanced combustion strategies, to replace, or combine with the conventional spark ignition strategy. One possible strategy is homogeneous charge compression ignition (HCCI) achieved using negative valve overlap (NVO). However, several issues need to be addressed before this combustion strategy can be fully implemented in a production vehicle, one being to increase the upper load limit. One constraint at high loads is the combustion becoming too rapid, leading to excessive pressure-rise rates and large pressure fluctuations (ringing), causing noise. In this work, efforts were made to reduce these pressure fluctuations by using a late injection during the later part of the compression. A more appropriate acronym than HCCI for such combustion is SCCI (Stratified Charge Compression Ignition).

For the application to Gasoline Homogenous Charge Compression Ignition (HCCI) modeling, a multi-zone model was developed. For this purpose, the detailed-chemistry code SENKIN from the CHEMKIN library was modified. In a previous paper, the authors explained how piston motion and a heat transfer model were implemented in the SENKIN code to make it applicable to engine modeling. The single-zone model developed was successfully implemented in the engine cycle simulation code AVL BOOST™. A multi-zone model, including a crevice volume, a quench layer and multiple core zones, is introduced here. A temperature distribution specified over these zones gives this model a wider range of application than the single-zone model, since fuel efficiency, emissions and heat release can now be predicted more accurately. The SENKIN-BOOST multi-zone model predictions are compared with experimental data.

In a diesel engine, the combustion and emissions formation are governed by the spray formation and mixing processes. To meet the stringent emission legislations of the future, which will demand substantial reductions of NOX and particulate emissions from diesel engines, the spray and mixing processes play a major roll. Different fuel injection systems and injection strategies have been developed to achieve better performance and lower emissions from the diesel engine almost without investigating the influence of the injector nozzle orifices. A reduction in the nozzle orifice diameter is important for an increased mixing rate and formation of smaller droplets which is beneficial from emissions and fuel consumption point of view, as long as the local air-to-fuel ratio (AFR) is kept at a sufficiently lean level.

Many technological developments in automobile powertrains have been implemented in order to increase efficiency and comply with emission regulations. Although most of these technologies show promising results in official fuel economy tests, their benefits in real driving conditions and real driving emissions can vary significantly, since driving profiles of many drivers are different than the official driving cycles. Therefore, it is important to assess these technologies under different driving conditions and this paper aims to offer an overall perspective, with a numerical study in simulations. The simulations are carried out on a compact passenger car model with eight powertrain configurations including: a naturally aspirated spark ignition engine, a start-stop system, a downsized engine with a turbocharger, a Miller cycle engine, cylinder deactivation, turbocharged downsized Miller engine, a parallel hybrid electric vehicle powertrain and an electric vehicle powertrain.

This study reflects on two areas of vehicle aerodynamics, optimising cooling performance and features that will improve the handling of the car. Both areas will have a significant impact on the overall performance of the car and at the same time these areas are linked to each other. The considered vehicle in this study was the Chalmers Formula Student 2011 Formula SAE car and the flow field was analysed using both numerical simulations as well as performing wind tunnel experiments on a 1:3-scale model of the car. The focus on increasing downforce without increasing the aerodynamic drag is particularly good in Formula SAE since fuel economy is an event at the competition. Therefore, the intention of this work is to present a study on how undertrays with different design such as added foot plates, diffuser and strakes can improve the downforce and reduce the drag.

Due to stricter emission regulations and more environmental awareness, the powertrain systems are moving toward higher fuel efficiency and lower emissions. In response to these pressing needs, new technologies have been designed and implemented by manufacturers. As a result of increasing complexity of the powertrain systems, their control and optimization become more and more challenging. Virtual powertrain calibration, also known as model-based calibration, has been introduced to transfer a part of test bench testing into a virtual environment, and hence considerably reduce time and cost of product development process while increasing the product quality. Nevertheless, virtual calibration has not yet reached its full potential in industrial applications. Volvo Penta has recently developed a virtual test cell named VIRTEC, which is used in an ongoing pilot project to meet the Stage V emission standards.

Plug-in hybrid electric vehicles (PHEVs) have rechargeable energy storage which can be used to run the vehicle on shorter range on electricity from the grid. In the absence of a priori information about the trip, a straightforward strategy is to first deplete the battery down to a minimum level and then keep the state of charge (SoC) around this level. However, largely due to the battery losses, the overall fuel economy can be improved if the battery is discharged gradually. This requires some a priori knowledge about the trip. This paper investigates the tradeoff between improved fuel economy and the need for a priori information. This investigation is done using a variant of telemetry equivalent consumption minimization strategy (T-ECMS) which is modified to be used for a PHEV. To implement this strategy, several parameters need to be tuned based on an assumption of the future trip.

In this study, the effects of varying the start of injection in a Free Piston Engine (FPE) have been investigated, using the KIVA-3V CFD code. In order to simulate the FPE the code has been modified by replacing the conventional crank shaft controlled piston motion by a piston motion profile calculated using a MATLAB/SIMULINK model. In this model, the piston motion is controlled by Newton's second law and the combustion process is represented by a simplified model based on ignition delay integrals and Wiebe functions. The results were tuned using predictions from the SENKIN software which are based on the detailed chemical kinetics mechanism of a Diesel oil surrogate represented by a blend of the main aliphatic (70% n-heptane) and aromatic (30% toluene) components. In order to help analyze the emission formation resulting from the HCCI/PPCI combustion modes in the engine, a special approach based on the temperature-equivalence ratio maps has been developed.

This work presents a numerical method for predictions of HC oxidation in the cold turbulent wall jet emerging from the piston top land crevice in an S.I. engine, using a complex chemical reaction model. The method has been applied to an engine model geometry with the aim to predict the HC oxidation rate under engine - relevant conditions. According to the simulation a large amount of HC survives oxidation due to the long ignition delay of the wall jet emitted from the crevice. This ignition delay, in turn depends mainly on chemical composition and temperature of the gas mixture in the crevice and also on the temperature distribution in the cylinder boundary layer.

The free piston internal combustion engine used in conjunction with a linear alternator offers an interesting choice for use in hybrid vehicles. The linear motion of the pistons is directly converted to electricity by the alternator, and the result is a compact and efficient energy converter that has only one moving part. The movement of the pistons is not prescribed by a crank mechanism, but is the result of the equilibrium of forces acting on the pistons, and the engine will act like a mass-spring system. This feature is one of the most prominent advantages of the FPE (Free Piston Engine), as the lack of mechanical linkage gives means of varying the compression ratio in simple manners, without changing the hardware of the engine. By varying the compression ratio, it is also it possible to run on a multitude of different fuels and to use HCCI (Homogeneous Charge Compression Ignition) combustion.

This paper investigates how particulates number PN is influenced by fuel wall-film, liner wetting, and the mixing quality for different start of injection timings (SOI). Both experimental data with PN measurements, endoscope images from a high-speed camera from a single-cylinder engine, and CFD simulations were used for the analysis. Engine geometry was a spray-guided system with 300 bar fuel pressure and with single injections. Data was captured for 2000 rpm / 9 bar IMEPn. The results show that fuel film on the piston was only found to significantly increase PN for over-advanced SOI (in our engine geometry, earlier than -310 CAD). This results in luminescence from diffusion burn on the piston surface, which strongly contributes to PN. For an SOI timing of -310 CAD, fuel film on piston reaches a maximum of 3% of the injected fuel, vaporizes, and no remaining fuel film is found at the time of ignition. Approximately 0.5-1% of the fuel ends up on the liner.

A new engine design concept, characterized by a single cylinder-double piston and a cycloid crank rotor instead of the conventional crankshaft has been developed recently by Gul & Co Development AB, Sweden. The rotor (crank disc) is equipped with an oval groove in the shape of a sinusoidal cycloid according to the expression varies from 0 to 1. Inside the oval groove a ball rolls/slides in order to transfer force from the piston to the rotor. Such a rotor contains groove surfaces for the valve movement control as well. Each turn of the rotor corresponds to four strokes for both the pistons. Thus, a full 4-stroke engine cycle is developed for a single non-conventional crankshaft revolution. Having the extra freedom to select an optimal piston movement, the new design is believed to have the potential to provide low emissions, low noise levels and lower fuel consumption. Therefore, it has been subjected to an engine thermodynamics simulation, to provide an insight to engine performance.

Look ahead information can be used to improve the powertrain’s fuel consumption while efficiently controlling exhaust emissions. A passenger car propelled by a Euro 6d capable diesel engine is studied. In the conventional approach, the diesel powertrain subsystem control is rule based. It uses no information of future load requests but is operated with the objective of low engine out exhaust emission species until the Exhaust After-Treatment System (EATS) light off has occurred, even if fuel economy is compromised greatly. Upon EATS light off, the engine is operated more fuel efficiently since the EATS system is able to treat emissions effectively. This paper presents a supervisory control structure with the intended purpose to operate the complete powertrain using a minimum of fuel while improving the robustness of exhaust emissions.

Increasing the injection pressure in gasoline direct injection engines has a substantial potential to reduce emissions while maintaining a high efficiency in spark ignition engines. Present gasoline injectors are operating in the range of 20 MPa to 25 MPa. Now there is an interest in higher fuel injection pressures, for instance, around 40 MPa, 60 MPa and even higher pressures, because of its potential for further emission reduction and fuel efficiency improvements. In order to fully utilize the high-pressure fuel injection technology, a fundamental understanding of gasoline spray characteristics is vital to gain insight into spray behavior under such high injection pressures. The understanding achieved may also be beneficial to improve further model development and facilitate the integration of such advanced injection systems into future gasoline engines.

Gasoline direct injection (GDI) engines usually emit higher levels of particulates in warm-up conditions of a driving cycle. Thus, sources of soot formation in these conditions were investigated by measuring particulate numbers (PN) emitted from a single-cylinder GDI engine and their sizes. The combustion was also visualized using an endoscope connected to a high-speed camera. Engine coolant and oil temperatures were varied between 15 and 90oC to mimic warm-up conditions. In addition, effects of delaying the start of ignition (SOI) on the emissions in these conditions were examined. Coolant and oil temperatures were varied individually to identify which factor has most effect on PN emissions. While coolant temperature strongly influenced PN with cold oil, the oil temperature insignificantly affected PN at low coolant temperature. These findings indicate that PN emissions are heavily dependent on the engine block’s temperature, which is dominated by the coolant.

Piston temperature experiments were conducted in a single-cylinder heavy-duty Diesel research engine, based on the Volvo Powertrain D12C engine both by use of optical temperature sensitive phosphor and of thermocouples mounted on the piston surface. In the former case, a thin coating of a suitable thermographic phosphor was applied to the areas on the piston surface to be investigated. The optical measurements of piston temperatures made involved use of an optical window and of an endoscope. The possibility of using optical fibres into guide light in and out of the engine was also investigated. Results of the optical and of the thermocouple measurements were compared and were also related to more global data with the aim of exploring the use of thermographic phosphors for piston- temperature measurements in Diesel engines. Thermographic phosphors thermometry was found to represent an alternative to the thermocouple method since it easily can be applied to various piston geometries.