Search Results

Gasoline Homogeneous Charge Compression Ignition (HCCI) combustion has been studied widely in the past decade. However, in HCCI engines using negative valve overlap (NVO), there is still uncertainty as to whether the effect of pilot injection during NVO on the start of combustion is primarily due to heat release of the pilot fuel during NVO or whether it is due to pilot fuel reformation. This paper presents data taken on a 4-cylinder gasoline direct injection, spark ignition/HCCI engine with a dual cam system, capable of recompressing residual gas. Engine in-cylinder samples are extracted at various points during the engine cycle through a high-speed sampling system and directly analysed with a gas chromatograph and flame ionisation detector. Engine parameter sweeps are performed for different pilot injection timings and quantities at a medium load point.

A Stochastic Reactor Model (SRM) has been used to simulate the transition from Spark Ignition (SI) mode to Homogeneous Charge Compression Ignition (HCCI) mode in a four cylinder in-line four-stroke naturally aspirated direct injection SI engine with cam profile switching. The SRM is coupled with GT-Power, a one-dimensional engine simulation tool used for modelling engine breathing during the open valve portion of the engine cycle, enabling multi-cycle simulations. The model is initially calibrated in both modes using steady state data from SI and HCCI operation. The mode change is achieved by switching the cam profiles and phasing, resulting in a Negative Valve Overlap (NVO), opening the throttle, advancing the spark timing and reducing the fuel mass as well as utilising a pilot injection. Experimental data is presented along with the simulation results.

A previously developed Stochastic Reactor Model (SRM) is used to simulate combustion in a four cylinder in-line four-stroke naturally aspirated direct injection Spark Ignition (SI) engine modified to run in Homogeneous Charge Compression Ignition (HCCI) mode with a Negative Valve Overlap (NVO). A portion of the fuel is injected during NVO to increase the cylinder temperature and enable HCCI combustion at a compression ratio of 12:1. The model is coupled with GT-Power, a one-dimensional engine simulation tool used for the open valve portion of the engine cycle. The SRM is used to model in-cylinder mixing, heat transfer and chemistry during the NVO and main combustion. Direct injection is simulated during NVO in order to predict heat release and internal Exhaust Gas Recycle (EGR) composition and mass. The NOx emissions and simulated pressure profiles match experimental data well, including the cyclic fluctuations.

Recent studies in the USA have revealed that the catalysts (which are universally fitted to gasoline automobiles) are failing in service to an unacceptable extent. Although the reasons for the failures are not completely clear, it seems that misfiring, leading to highly exothermic reaction in the catalyst, may be responsible for the damage. Legislation is to be enacted later in this decade to address this problem by requiring on board diagnostic (OBD) systems which can measure misfire, as well as catalyst hydrocarbon (HC) conversion efficiency. Although some ideas have been suggested for the OBD requirements, no fully satisfactory sensor technology has yet appeared. This paper describes a novel hydrocarbon sensor based on a surface catalysis principle. The fundamental studies reported here have been made with the automobile application in mind. A catalytic chemi-ionisation model is proposed in order to enhance our understanding of this surface ionisation.

Common-rail fuel injection systems on modern light-duty diesel engines are effectively able to respond instantaneously to changes in the demanded injection quantity. In contrast, the air-system is subject to significantly slower dynamics, primarily due to filling/emptying effects in the manifolds and turbocharger inertia. The behavior of the air-path in a diesel engine is therefore the main limiting factor in terms of engine-out emissions during transient operation. This paper presents a simple mean-value model for the air-path during throttled operation, which is used to design a feed-forward controller that delivers very rapid changes in the in-cylinder charge properties. The feed-forward control action is validated using a state-of-the-art sampling system that allows true cycle-by-cycle measurement of the in-cylinder CO₂ concentration.

Partially premixed compression ignition (PPCI) engines operating with a low temperature highly homogeneous charge have been demonstrated previously using conventional diesel fuel. The short ignition delay of conventional diesel fuel requires high fuel injection pressures to achieve adequate premixing along with high levels of EGR (exhaust gas recirculation) to achieve low NOx emissions. Low load operating regions are typified by substantial emissions of CO and HC and there exists an upper operating load limitation due to very high rates of in-cylinder gas pressure rise. In this study mixtures of gasoline and diesel fuel were investigated using a multi-cylinder light duty diesel engine. It was found that an increased proportion of gasoline fuel reduced smoke emissions at higher operating loads through an increase in charge premixing resulting from an increase in ignition delay and higher fuel volatility.

Highly homogeneous compression ignition is difficult to achieve in a direct injection diesel engine. The difficulty of achieving adequate fuel vaporization and the problems of fuel spray wall impingement are the main factors. Limitation of the maximum operating load results from high rates of pressure rise that occur in this combustion regime. The levels of HC and CO emissions are raised substantially when compared with conventional combustion and remain a significant emission factor. In this study, two methods of achieving highly homogeneous combustion in a direct injection diesel engine were investigated, Nissan MK type and early injection. The effects of fuel injection pressure, injection timing, EGR level, EGR cooler efficiency and compression ratio were examined using a conventional 4 cylinder 2.0L common rail diesel engine with 18.4:1 and 14.4:1 compression ratios.

The gas velocity through an automotive catalyst has been determined by measuring the time of flight of a pulse of propane injected at the inlet plane of the catalyst. The arrival time at the exit plane was detected by a fast flame ionization detector. By synchronizing and delaying the injection of propane with respect to the engine crankshaft position, the fluctuations of the exhaust gas velocity during the engine cycle were investigated. A number of tests at different engine load and speed points were carried out. The results show a complex velocity/time characteristic, including flow reversals. The technique is shown to be a viable option for flow measurement in this harsh environment.

A novel Fast Response Chemiluminescence Detector and a Fast Flame Ionization detector have been used to examine the instantaneous NO and unburnt hydrocarbon concentration in the cylinder and exhaust port of a DI Diesel engine. The in-cylinder results indicate very high levels of NO in the premixed phase of combustion, followed by generally lower levels during the diffusion burning phase. Hydrocarbon signals also indicate significant detail. The in-cylinder uHC signal is consistent with the probe location being between two of the fuel sprays. Both in-cylinder and exhaust results indicate rather high cyclic variability in the NO levels at steady conditions. Variations in the timing and structure of the exhaust uHC signal during the valve open period with load may give insight into the fuel spray/air motion.

A novel mechanical method of achieving a rapid switch between stoichiometric and lean conditions for SI engines is explored. Two and three throttle configurations, a switch strategy which employs a standard intake manifold and an assembly of pipes and throttle(s), are investigated numerically by using a one-dimensional engine simulation program based on the method of characteristics. The results indicate that it is possible to achieve rapid AFR switch without a torque jump, i.e. unperceptible to the driver.

An established Stochastic Reactor Model (SRM) is used to simulate the transition from Spark Ignition (SI) to Homogeneous Charge Compression Ignition (HCCI) combustion mode in a four-cylinder in-line four-stroke naturally aspirated direct injection SI engine with cam profile switching. The SRM is coupled with GT-Power, a one-dimensional engine simulation tool used for modeling engine breathing during the open valve portion of the engine cycle, enabling multi-cycle simulations. The mode change is achieved by switching the cam profiles and phasing, resulting in a Negative Valve Overlap (NVO), opening the throttle, advancing the spark timing and reducing the fuel mass as well as using a pilot injection. A proven technique for tabulating the model is used to create look-up tables in both SI and HCCI modes. In HCCI mode several tables are required, including tables for the first NVO, transient valve timing NVO, transient valve timing HCCI and steady valve timing HCCI and NVO.

Models often use time rather than strokes (crank-angle) as the independent variable to describe engine dynamics despite the fact that the dynamics of an internal combustion engine are intrinsically linked to the combustion events. In this paper, two models are developed in parallel in which not only the independent variable is changed but the notion of mass flows as well: flows are in [g/s] for the time-based model and in [g/st] for the event-based model. Both models are of the same computational complexity and show the same accuracy in validation. The investigation of the model properties shows that variations in the flow-related parameters are reduced by a factor of two to five for the event-based model. However, those of the crankshaft dynamics are increased. It is concluded that the model should be chosen in context of the control system to be designed.

Experimental data was obtained from a Rover K4 optical access engine and analyzed with a combustion analysis package. Cyclic NO values were calculated by mass averaging the measurements obtained by a fast NO analyzer. While the mass averaged results were used as the basis of comparison for the model, results indicate that mass averaging a fast NO signal is not nearly as critical as mass averaging a fast FID signal. A computer simulation (ISIS - Integrated Spark Ignition engine Simulation) was used to model the NO formation on a cyclic basis by means of the extended Zeldovich equations. The model achieves its cyclic variability through the input of experimentally derived burn rates and a completeness of combustion parameter, which is based on the Rassweiler and Withrow method of calculating mass fraction burned and is derived from the pressure-crank angle record of the engine.

The benefits of deliberately modulating air-to-fuel ratio over a three-way catalyst are disputed. In this work, engine test cell experiments were carried out to assess the performance of a warmed-up Pd/Rh three-way catalyst. The objectives were threefold: first, to determine the best mode of operation; second, to determine if air-to-fuel ratio modulation enhances robustness to transient air-to-fuel ratio disturbances; third, to determine if the conversion efficiency can be manipulated by controlling the shape of the air-to-fuel ratio oscillation. It was observed that the highest conversion efficiency is obtained using a steady air-to-fuel ratio just rich of stoichiometric; however, this mode of operation lacks robustness with respect to transient disturbances and UEGO sensor errors. Robustness can be improved using an oscillating air-to-fuel ratio, but with a sacrifice in peak conversion efficiency.

Particulate emissions from IC engines associated with transient engine conditions are very important (similar to the legislated gaseous emissions). This is true both during real-world and test cycle driving. This paper describes an instrument for measuring the number of particles, and their spectral weighting, in the 5nm to 1000nm size range, with a time response of 200ms. This is achieved via an electrostatic classification technique, consisting of a diffusion charger followed by a multi-element, constant voltage, classifier. Conversion of the data to other metrics, such as mass, is also described. Results are presented from artificial test aerosols and from light and heavy duty diesel engines on standard test cycles.

The parameterization of variable geometry turbochargers for mean-value modeling is typically based on compressor and turbine flow and efficiency maps provided by the supplier. At low turbocharger speeds, and hence low airflows, the heat exchange via the turbocharger housing affects the temperature-based measurements of the efficiencies. Therefore, the low-speed operating regime of the turbocharger is excluded from the supplied maps and mean-value models mainly rely on extrapolation into this region, which is regularly met in emission drive cycles, and hence of significance. This paper presents experimental data from a 2.0-liter turbocharged common-rail diesel engine. While the flow maps extend from the high-speed region in a natural way, the efficiency maps are severely affected by the heat transfer effect. It is argued that this effect should be included in the mean-value model.

A technique is presented for measuring the exhaust gas recirculation (EGR) and residual gas fraction (RGF) using a fast UEGO-based O₂ measurement of the manifold or in-cylinder gases, and of the exhaust gases. The technique has some advantages over the more common CO₂-based method. In the case of an RGF measurement, fuel interference must be eliminated and special fuelling arrangements are required. It is shown how a UEGO-based measurement, though sensitive to reactive species in the exhaust (such as H₂), as a system reports EGR/RGF rates faithfully. Preliminary tests showed that EGR and RGF measurements using the O₂ approach agreed well with CO₂-based measurements.

Delivering acceptable low end torque and good transient response is a significant challenge for all turbocharged engines. As downsized gasoline engines and Diesel engines make up a larger and larger proportion of the light-duty engines entering the market, the issue takes on greater significance. Several schemes have been proposed to improve torque response in highly boosted engines, including the use of electrical assist turbochargers and compressed air assist. In this paper we examine these methods with respect to their effectiveness in improving transient response and their relative performance along with some of the practical considerations for real world application. Results shown in this paper are from 1-D simulations using the Ricardo WAVE software package.

Recent work has investigated the use of O₂ concentration in the intake manifold as a control variable for diesel engines. It has been recognized as a very good indicator of NOX emissions especially during transient operation, however, much of the work is concentrated on estimating the O₂ concentration as opposed to measuring it. This work investigates Universal Exhaust Gas Oxygen (UEGO) sensors and their potential to be used for such measurements. In previous work it was shown that these sensors can be operated in a controlled pressure environment such that their response time is of the order 10 ms. In this paper, it is shown how the key causes of variation (and therefore potential sources of error) in sensor output, namely, pressure and temperature are largely mitigated by operating the sensors in such an environment. Experiments were undertaken on a representative light-duty diesel engine using modified UEGO sensors in the intake and exhaust system.

A key challenge in achieving good transient performance of highly boosted engines is the difficulty of accelerating the turbocharger from low air flow conditions (“turbo lag”). Multi-stage turbocharging, electric turbocharger assistance, electric compressors and hybrid powertrains are helpful in the mitigation of this deficit, but these technologies add significant cost and integration effort. Air-assist systems have the potential to be more cost-effective. Injecting compressed air into the intake manifold has received considerable attention, but the performance improvement offered by this concept is severely constrained by the compressor surge limit. The literature describes many schemes for generating the compressed gas, often involving significant mechanical complexity and/or cost. In this paper we demonstrate a novel exhaust assist system in which a reservoir is charged during braking.