Search Results

NVH quality is one of the most important criteria by which people judge the design of a vehicle. The Powertrain Mounting System (PMS), which can reduce the vibration from engine to vehicle cab as well as the inside noise, has attained significant attention. Much research has been done on the isolation method for three- and four-point mounting. But the six-point mounting system, which is usually equipped in commercial vehicle, is seldom studied and should be paid more attention. In this paper, the support rod installed on the upside of the transmission case is considered as a flexible body. Thus a rigid-flexible coupling model of PMS is established and the necessity of the established model is analyzed by comparing the simulation results of the new model and those of the conventional model.

The suspension system of a heavy truck's driver seat plays an important role to reduce the vibrations transmitted to the seat occupant from the cab floor. Air-spring is widely used in the seat suspension system, for the reason that its spring rate is variable and it can make the seat suspension system keep constant ‘tuned’ frequency compared to the conventional coil spring. In this paper, vibration differential equation of air-spring system with auxiliary volume is derived, according to the theory of thermodynamic, hydrodynamics. The deformation-load static characteristic curves of air-spring is obtained, by using a numerical solution method. Then, the ADAMS model of the heavy truck's driver seat suspension system is built up, based on the structure of the seat and parameters of the air-spring and the shock-absorber. At last, the model is validated by comparing the simulation results and the test results, considering the seat acceleration PSD and RMS value.

Nowadays, studying the human body response in a seated position has attracted a lot of attention as environmental vibrations are transferred to the human body through floor and seat. This research has constructed a multi-body biodynamic human model with 17 degrees of freedom (DOF), including the backrest support and the interaction between feet and ground. Three types of human biodynamic models are taken into consideration: the first model doesn't include the interaction between the feet and floor, the second considers the feet and floor interaction by using a high stiffness spring, the third one includes the interaction by using a soft spring. Based on the whole vehicle model, the excitation to human body through feet and back can be obtained by ride simulation. The simulation results indicate that the interaction between feet and ground exerts non-negligible effect upon the performance of the whole body vibration by comparing the three cases.

The dual clutch transmission is one of the possible choices for electric vehicle drivelines. The basic principle and control mode of shifting of wet dual clutch transmission are introduced, and the dynamic process of shifting of wet double clutch transmission is studied. Combined with the dynamic model of the wet clutch engagement process, the difference between the dynamic characteristics of the dual clutch transmission modeling using the Coulomb friction model and the dual-clutch transmission model using the average flow model and the micro-convex contact theory is analyzed. The shift control strategy of the dual clutch transmission proposes a correction method to improve the shifting smoothness. Studies have shown that the torque response of the wet clutch has significant hysteresis, and the improved control algorithm can significantly improve the shifting smoothness of the wet dual clutch transmission.

In this paper, a multi-mode active seat suspension with a single actuator is proposed and built. A one-DOF seat suspension system is modelled based on a quarter car model of commercial vehicle with an actuator which is comprised of a DC motor and a gear reducer. Aiming at improving ride comfort and reducing energy consumption, a multi-mode controller is established. According to the seat vertical acceleration and suspension dynamic travel signals, control strategies switch between three modes: active drive mode, energy harvesting mode and plug breaking mode.

To design and optimize the vehicle driveline is necessary to decrease the fuel consumption and improve dynamic performance. This paper describes a methodology to optimize the driveline design including the axle ratio, transmission shift points and transmission shift ratios considering uncertainty. A new and flexible tool for modeling multi-domain systems, Modelica, is used to carry out the modeling and analysis of a vehicle, and the multi-domain model is developed to determine the optimum design in terms of fuel economy, with determinability. Secondly, a robust optimization is carried out to find the optimum design considering uncertainty. The results indicate that the fuel economy and dynamic performance are improved greatly.

The automatic mechanical transmission (AMT) was designed by automobile manufacturers to provide a better driving experience, especially in cities where congestion frequently causes stop-and-go traffic patterns. It uses electronic sensors, processors, hydraulic or pneumatic actuators execute clutch actuation and gear shifts on the command of the driver. Such systems coupled with various physical domains have great influence on the dynamic behavior of the vehicle, such as shift quality, driveability, acceleration, etc. This paper presents a detailed AMT model composed of various components from multi-domains like mechanical systems (clutch, gear pair, synchronizer, etc.), pneumatic actuator systems (clutch actuation system, gear select actuation system, gear shift actuation system, etc.). Various components and subsystem models, such as the vehicle, engine, AMT, wheels, etc., are integrated into an overall vehicle system model according to the transmission power flow and control logic.

Electric vehicles driven by in-wheel-motor have the advantages of compact structure and high transmission efficiency, which is one of the most ideal energy-saving, environmentally friendly, and safe driving forms in the future. However, the addition of the in-wheel-motor significantly increases the unsprung mass of the vehicle, resulting in a decrease in the mass ratio of the vehicle body to the wheel, which will deteriorate the ride comfort and safety of the vehicle. To improve the vibration performance of in-wheel-motor driven vehicles, a semi-active inerter-spring-damper (ISD) suspension with in-wheel-motor (IWM) dynamic vibration absorber (DVA) of the electric wheel is proposed in this paper. Firstly, a structure of in-wheel-motor DVA is proposed, which converts the motor into a dynamic vibration absorber of the wheel to suppress the vibration of the unsprung mass.

For vehicles equipped with dry dual clutch transmission, due to the diversity of starting conditions, it is a nontrivial task for control strategy to meet the requirements of all kinds of complex starting conditions, which is easy to cause large starting shock and serious clutch wear. Therefore, it is proposed in this paper an adaptive control strategy for complex starting conditions by adjusting two clutches to participate in the starting process at the same time. On the basis of establishing the transmission system model and clutch model, the starting conditions are identified in terms of starting speed, road adhesion and driver's intention, in which the driver's intention is identified by fuzzy reasoning model. Based on the identification of starting conditions and considering the safety principle, it is selected the appropriate starting gear and clutch combination mode, and adjusted the combination speed of the two clutches to carry out an adaptive control strategy.

Increased focus on vehicle comfort and ride has led the automotive industry to look into low vibration, noise and hardness alternative designs for powertrain system components. In this paper, the vibration theory and dynamic vibration absorber (DVA) theory is presented. The modal analysis of propeller shaft assembly has been accomplished. Based on dynamic vibration absorber principle, performance parameters of dynamic vibration absorber are matched and structure is also designed. LMS equipment is applied to verify the natural frequency of absorber samples. The matching of stiffness and damping of DVA is presented. The dynamic response of drive shaft system based on the mass ratio of DVA is researched in this paper. Results from simulations and tests indicates that the amplitude of propeller shaft resonance can be effectively reduced by attaching a DVA to the long propeller shaft.

The imbalance of propeller shaft is an excitation to the vehicle structure and causes noise and vibration. This paper presents an experimental study of effects of propeller shaft imbalance on vehicle vibration characteristics. A two-piece propeller shaft with unbalance is used in real vehicle test. The vehicle vibration is characterized by accelerations of the cabin floor and of the bearing which supports the propeller shaft. Through the experiment, some interesting phenomena are observed.

Vehicle Thermal Management System (VTMS) is a crosscutting technology affecting the fuel consumption, engine performance and emissions. With the new approved fuel economy targets and the enhanced vehicle performance requirements, the ability to predict the impact on the fuel consumption of different VTMS modifications is becoming an important issue in the pre-prototype phase of vehicle development. This paper presents a methodology using different simulation tools to model the entire VTMS in order to understand and quantify its behavior. The detailed model contains: engine cooling system, lubrication system, powertrain system, HVAC system and intake and exhaust system. A detail model of the power absorbed by the accessory components operating in VTMS such as pumps and condenser is presented. The power of the accessory components is not constant but changing with respect to engine operation. This absorbed power is taken into account within the power produced by the engine shaft.

A simulation model of the single cone synchronizer is presented using the dynamic implicit algorithm with commercial Finite Element Analysis (FEA) software Abaqus. The meshing components include sleeve gear, blocking ring and clutch gear, which are all considered as deformation body. The processes mainly contain the contact between sleeve teeth and blocking teeth, meshing period and the impact of sleeve teeth and clutch gear teeth, and these nonlinear contact steps are realized with Abaqus. In addition, a shift force derives from experiment is applied to the sleeve ring, and a moment is added to the clutch gear to realize the relative rotational speed. Based on the FEA model, the effect of the varied frictional coefficients between the cone surfaces of blocking ring and clutch gear on the synchronizer time and contact stress is discussed. Variation of stresses and contact force with respect to time are evaluated from this analysis.

In order to reasonably match the variable stiffness and location of the Powertrain Mounting System (PMS) and optimize the ride comfort of commercial vehicle, a thirteen degrees of freedom (DOF) model of a commercial vehicle was established in Adams/view. Specially, the support rod installed on the upside of the transmission case was modeled as a flexible body. The vibration isolation provided by the PMS was evaluated in three aspects: the energy decoupling of the powertrain, the response force of the mount and the displacement of the powertrain. The energy decoupling ratio, the force RMS of the mount when force excitation was applied on the powertrain and the displacement of the powertrain Center of Gravity (C.G) when displacement excitation was applied on the vehicle chassis were selected as the optimal target. Adams and MATLAB were integrated into the optimization software iSIGHT to optimize the PMS. NSGA-II is used to obtain some Pareto-optimal solutions of PMS.

This paper presents the dynamic and analysis models of a typical synchronizer, which are mainly used to analyze the sensitivity of parameters of synchronizer on the gear shift performance. Because there are so many parameters namely coefficient of friction, cone angle, mean radius, blocker angle, etc, affected the synchronizer performance, which the times of experience will increase in a geometrical ratio if tested them one by one, it is almost impossible to evaluate all parameters by experience alone. Due to virtual prototype technology, the synchronizer parameterized virtual models can be built for the synchronizer studies. The parameterized virtual models of the typical synchronizers are developed with ADAMS. Then the gear shift process is simulated and analyzed for the given input parameters respectively. The models also predict the shift time and the peak of the shift force, and the model is validated by the good correlation between simulation results and test data.

The powertrain mounting system (PMS) plays an important role in improving the NVH (Noise, Vibration, Harshness) quality of the vehicle. In all running conditions of a vehicle, the displacements of the powertrain C.G. should be controlled in a prescribed range to avoid interference with other components in the vehicle. The conventional model of PMS is based on vibration theory, considering the rotation angles are small, ignoring the sequence of the rotations. However, the motion of PMS is in 3D space with 3 translational degrees of freedom and 3 rotational degrees of freedom, when the rotation angles are not small, the conventional model of PMS will cause errors. The errors are likely to make powertrain interfering with other components. This paper proposes a rigid body mechanics model of the powertrain mounting system. When the powertrain undergoes a large rotational motion, the rigid body mechanics model can provide more accurate calculation results.

Vehicle Thermal Management System (VTMS) is a cross-cutting technology that directly or indirectly affects engine performance, fuel economy, safety and reliability, driver/passenger comfort, emissions. This paper presents a novel methodology to investigate VTMS based on Modelica language. A detailed VTMS platform including engine cooling system, lubrication system, powertrain system, intake and exhaust system, HVAC system is built, which can predict the steady and transient operating conditions. Comparisons made between the measured and calculated results show good correlation and approve the forecast capability for VTMS. Through the platform a sensitivity analysis is presented for basic design variables and provides the foundation for the design and matching of VTMS. Modelica simulation language, which can be efficiently used to investigate multi-domain problems, was used to model and simulate VTMS.

Clutch actuation systems are complex systems where hydraulic, pneumatic, mechanical and electrical components are coupled. This paper presents a detailed clutch actuation model composed of components from multi-domains like mechanical and pneumatic actuation system, hydraulic boosting system, etc. Various components and subsystem models, such as the driver, engine, gear pairs, clutches, etc., are integrated into an overall vehicle system model according to the transmission power flow and control logic. The model is implemented using the Modelica programming language. The simulation of the clutch actuation system was carried out for the analysis of drivability, shift quality and vehicle overall performance.

Unsuitable shift control strategies may increase the vehicle jerk and clutch wear. In order to improve the shift quality of electric vehicles (EVs) equipped with dual clutch transmission, this paper proposes an optimal shift control strategy based on linear quadratic regulator, in which weighting matrices are selected by using genetic algorithm (GA). The dynamics of the shift process of the dual clutch transmission is analyzed to establish the dynamic model of the driving system. In addition to the vehicle jerk, the friction work of clutch is also considered as one of the performance criteria and a new linear quadratic objective function is formulated. The optimal weighting matrices for obtaining a globally optimal solution are selected benefit from the global search capacity of genetic algorithm. The optimal target trajectories of the torque of the two clutches and motor are obtained by simulating the linear quadratic regulator (LQR).

The automatic transmission of a specialized vehicle encountered challenges in achieving stable oil filling time due to the considerable variability of related parameters and the non-linear trends in the variation of individual product parameters over time. To investigate the underlying causes of this phenomenon and enhance the oil filling efficiency, a detailed model of the clutch oil filling process during gear shifting was established in this paper, which included dynamic models of the key components such as the hydraulic system, clutch, proportional valve, and oil passages. Physical experiments were performed on the test bench to compare with the simulation results. The results showed that the correlation between the simulation model and the test bench was well, which verified the effectiveness of the simulation model.