Search Results

This paper describes the investigation into the contact pressure and incidental deformation on the contact surface of the piston skirt which comes in contact with the cylinder bore in operation. Focused on the single piston static tests in the first place, relationship between the contact pressure on said skirt and the strains developed inside the skirt, and the relationship between the deformation of skirt face and the strains inside the skirt were studied. Then, the dynamic contact pressure onto the skirt in operation and the amount of deformation were calculated based on the relationships mentioned above using the factor of dynamic strains measured on an engine in operation. The deformation of skirt calculated using said dynamic strains was verified by the direct measurement of the skirt deformation. It was demonstrated that the thrust side of a piston skirt was largely deformed due to enlarged contact pressure caused by the piston slap subsequent to firing top dead center.

This paper reports the results of a study into a preview control that uses the displacement of the road surface in front of the vehicle to improve for front and rear actuator responsiveness delays, as well as delays due to calculation, communication, and the like. This study also examined the effect of a preview control using the eActive3 electric active suspension system, which is capable of controlling the roll, pitch, and warp modes of vehicle motion.

In this paper, we discuss vehicle directional stability and introduce advanced stability control (ASTC) to stabilize the vehicle during severe cornering. Vehicle behavior in a transient steering condition during severe cornering was analyzed by computer simulation. It was found that applying an external yaw moment makes the vehicle more stable. The effect of controlling the brake force response is also evaluated by simulation to determine the brake actuator response criteria. The actual vehicle test was performed with a pylon slalom using a hydraulic brake actuator. It is verified that the ASTC stabilizes the vehicle for transient steering maneuvers.

It is well known that the self-aligning torque decreases before lateral force is saturated. Focusing on this self-aligning torque change, an estimation method has been developed to detect the friction condition between steered wheels and road surface before the lateral force reaches the friction limit. The lateral grip margin (LGM) is defined based on the self-aligning torque change, which is obtained using the EPS torque and motor current information. The LGM is theoretically analyzed based on the tire model and experimentally verified through the full-scale vehicle test. Moreover, the estimated LGM is applied for the chassis control systems to improve the vehicle dynamics performance.

Drive train components (transmission, differential gears, etc.) can be made smaller and lighter if the excessive torque exerted on them can be reduced during the quick start of a vehicle. An orifice put in the hydraulic clutch piping path is an effective method. However, increased oil viscosity at low temperatures (0°C or below) makes the “pedal feel” worse. In order to increase the orifice diameter for better “pedal feel”, a shape memory alloy spring, for operation at low temperatures, was developed by adding cobalt to the nickel-titanium alloy. Consequently, a Variable-Orifice valve, using the shape memory alloy spring, is practical.

As a process that enables the high-speed and continuous forming of lengthy materials with a constant cross-sectional configuration, roll forming offers much higher productivity than the stamping process. However, in case a change must be made to the shape of the cross section, the material must normally be stamped or joined with a part containing a separate shape. This affects productivity, increases the number of pieces, and degrades the material's appearance. This report describes the roll-forming technology that we developed, in which the cross section of the material can be changed gradually. This method adopts a system which uses a movable and rotatable roll-stand that enables high-speed, continuous roll-forming processes.

Electrification of the powertrain to improve vehicle fuel economy is a key technology to achieve strict fuel economy legislation. However, only limited numbers of small class vehicles such as a B segment adopt electric powertrain. This is presumed that cost effectiveness for fuel economy is small and mounting space for additional powertrain is limited. In this paper, the optimum solution of a strong hybrid system suitable for the small vehicles was studied. First, from the viewpoint of maximization of energy efficiency, we compared contributions of engine efficiency and transmission efficiency during mode cycle driving and selected automated manual transmission as a suitable transmission for small vehicles. In comparing the hybrid system function, we determined a motor generator connecting shaft and a necessary motor generator output power for attaining both fuel economy and drivability.

Active-TRAC (A-TRAC) is the system for off-road 4WD vehicles. This system consists of independent four wheel brake control system and engine torque control system. This system applies the brake to any spinning wheel, and sends torque to the other wheels with grip. Therefore, the vehicle gets strong LSD(Limited Slip Differential) effect, and it has the same traction performance as a center and rear differential locked vehicle. Because the vehicle with A-TRAC does not have a differential locking mechanism, it no longer has the phenomenon of tight corner braking, and it frees a driver from operating the differential locking system. Therefore anyone can easily enjoy off-road driving with A-TRAC.