Search Results

Vehicle handling is an important attribute that is directly related to vehicle safety. The rapid development of road infrastructure has resulted in a greater focus on safety and stability. Commercial vehicle stability and safety assumes higher significance because of high center of gravity (CG) and heavier loads. A gamut of parameters influence vehicle handling directly and indirectly. However, it is quite difficult to gauge through physical testing, the extent of each parameter's influence on handling. Therefore, this paper examines vehicle handling by way of a sensitivity analysis through numerical simulation. A prototype vehicle is also instrumented and tested to confirm trends and validate the results of the simulation. An Intermediate Commercial Vehicle (ICV) with Gross Vehicle Weight (GVW) of around 13 tonnes is modeled and parameters like wheelbase and tyre stiffness are altered and the effect of these changes on handling parameters (yaw rate, lateral acceleration) is observed.

In today competitive world, gaining customer delight is the most vital part of an automotive business. Customers’ expectations are high which need to be satisfied limitless, to stay in the business. The major expectation of a commercial vehicle customer is a vehicle without failures which involves lower spares cost and downtime. The significance of a suspension system in the new age automobiles is getting advanced. There have been many improvements in the suspension system especially in leaf springs to provide a better ride comfort, and one such modern era implementation is the Parabolic Spring which comprises of fewer leaves with varying thickness from the center to the ends without inter-leaf friction. Study reveals that parabolic spring exhibits better ride comfort, but less life compared to a conventional leaf spring which leads to the increase in downtime of the vehicle.

In the emerging commercial vehicle sector, it is very essential to give a product to customer, which is very reliable and less prone to the failures to make the product successful in the market. In order to make it possible, the product is to be validated to replicate the exact field conditions, where it is going to be operated. Lab testing plays a vital role in reproducing the field conditions in order to reduce the lead time in overall product life cycle development process. This paper deals with the design and fabrication of the steering column slip endurance test rig. This rig is capable of generating wear on the steering column splines coating which predominantly leads to failure of steering column. The data acquired from Proving Ground (PG) was analyzed and block cycles were generated with help of data analyzing tools.

Steering gear box function is one of the important requirements in heavy vehicles in order to reduce driver fatigue. Improper functioning of steering gear box not only increases the driver fatigue, also concerns the safety of the vehicle. In this present investigation, the engine oil mixing up with steering oil has been identified and steering gear box failure has been observed in the customer vehicle. The root cause of failure has been analyzed. Based on the investigations, in particular design of steering pump has been failed at customer end. The same design of steering pump were segregated and analyzed. Initial pressure mapping study has been conducted. The pressure mapping results revealed that the cavity pressure obstructs the flow of suction pressure. It indicates that obstacle at suction port due to the existence of internal leakage that causes back pressure in the internal cavity of steering pump which sucks engine oil.

New legislation’s, competition from global players and change in customer perception related to comfort parameters are key factors demanding manufactures to design and manufacture vehicles with very low saloon noise levels. The main causes for higher noise levels at passenger saloon compartment can be attributed to source noises (Powertrain, Driveline, Intake and Exhaust etc.), acoustic isolation and structural sensitivity of the body. Out of all above parameters, powertrain noise and acoustic isolation are two critical parameters effecting interior noise performance. This paper is an attempt to explain acoustic source contribution analysis through transfer function measurement in a passenger vehicle. Acoustic transfer function between engine bay and passenger ear level was measured using reciprocity technique (reciprocal method) with reference source placed at various locations inside the vehicle.

A major activity of any new vehicle development program, is to meet legal requirements of local markets. Pass by noise (PBN) test is one of the standardized tests and is used to certify new vehicles/variants for their Noise emissions. Certification for noise emissions of commercial vehicles is achieved by measuring external sound levels according to procedures defined by standards such as IS: 3028 for Indian market. Before a physical proto-vehicle is assembled, various systems and subsystems are readily made available by suppliers off the shelf. During final design validation of the vehicle by mule-vehicle testing, PBN target compliance need be assured for all these systems in order to meet overall PBN target. The PBN on an Intermediate commercial vehicle (ICV) migrated to the latest Exhaust emission standard, was the subject of this study. This vehicle emitted PBN greater than accepted threshold.

In today’s competitive world to stay in the commercial vehicle business, technological advancement is vital. Understanding the various operation modes of a vehicle considering the vibration becomes essential for developing a vehicle free from failures. ODS analysis is a method which is used to visualise the vibration pattern of a vehicle when influenced by known external operating forces. ODS provide very useful information for understanding and evaluating the behavior of the vehicle. This paper discusses about the experiments carried out in vehicle. It details the process of data collection at varying frequency input, understanding the modes at various frequencies, identifying the resonant frequency of various components, understanding the comparison between road inputs and resonance frequencies and the transfer of vibration (Transmissibility) from one component to another.

Powertrain is the major source of noise and vibration in commercial vehicles and has significant contribution on both interior and exterior noise levels. It is vital to reduce the radiated noise from powertrain to meet customer expectations of vehicle comfort and to abide by the legislative noise requirements. Sound intensity mapping technique can identify the critical components of noise radiation from the powertrain. Sound intensity mapping has revealed that oil sump as one of the major contributors for radiated noise from powertrain. Accounting the effect of dynamic coupling of oil on the sump is crucial in predicting its noise radiation performance. Through numerical methods, some amount of work done in predicting the dynamic characteristics of structures filled with fluid. This paper discusses on the capability of numerical approach in predicting the oil sump modal characteristics with fluid-structure interaction and consequent verification with experimental modal test results.

Exterior noise reduction of a vehicle has become important nowadays in order to meet the stringent pass by noise regulations. First step in this process is the identification of dominant noise sources. There are several noise sources which can contribute to the pass by noise like gearbox, turbocharger, oil sump, exhaust muffler, air intake etc. The dominant noise sources can be identified with the near field noise, component vibration measurements combined with experimental modal analysis. This paper discusses about the noise source identification and exterior noise reduction of a shortest wheel base intermediate commercial vehicle, which is having a 4-cylinder inline diesel engine.

The present work focusses on the Noise &Vibration refinement carried out on a Heavy commercial vehicle (HCV). In a heavy commercial 4×4 vehicle the existence of an auxiliary gearbox (AGB) is primarily for switching between the multiple drive options. The AGB can become an additional source of noise from the drive train. In this particular vehicle the overall noise from the vehicle has particularly been dominated by the noise from the AGB in specific drive options and conditions as experienced during the subjective assessment of the vehicle initially. First assessment was made by modifying the gear tooth geometry and then the gears were changed from spur to helical as a part of the AGB refinement process. The results of both these assessments were compared. A considerable improvement in the AGB noise was thereby achieved.

In the automotive industry several attributes needs to be considered for the development of a new vehicle which are important for the customer, such as vehicle dynamics, driveability, fuel consumption, emissions, durability and NVH among many others. Sometimes these characteristics are conflicting and often need is to create a robust trade-off where the design space is sufficient to fit all of them in a vehicle that rhymes with the brand image and is appealing to the intended customer. Automobile manufacturers try to meet the requirements with respect to quality and comfort and often, emotional, aspects supercede the previous objective, pragmatic demands. The satisfaction of the demands by the customers concerning comfort, driving pleasure, design appears dominant and functionality criteria sometimes takes a back seat. NVH is considered to be one of the key buy in factor among the above mentioned attributes.

Design decisions based on the virtual simulations leads to reduced number of prototype testing. Demonstrated correlation between the computer simulations and experimental test results is vital for designers to confidently take simulation driven design decisions. For the virtual design evaluation of durability, ride, handling and NVH performance, demonstration of correlation of structural dynamic characteristics is critical. Modal correlation between CAE and physical testing validates the stiffness and mass distribution used in the FE model by correlating mode shape and mode frequency in the desired frequency range. The objective of this study is to arrive at a method for establishing modal correlation between CAE and experimental test for a bare frame and thereby enabling evaluation of design iterations in virtual environment to achieve modal targets.

The demand for comfort level in commercial vehicles is steadily increasing. Hence, fine-tuned performance parameters and attributes are required to fulfill the expectations from these vehicles. Refinement of noise and vibration without affecting performances of sub-systems and components has become extremely challenging with increasing customer requirements. This paper presents an approach to identify and reduce the high level whistling noise that was perceived in the passenger compartment while the vehicle was accelerated above 50 kmph. Interior noise measurements in static engine run-up condition reveal that the whistling noise is of specific order. Since, whistling noise is related to aerodynamic response of components, engine cooling fan, turbo charger, alternators and compressors were suspected. Using order tracking and near field measurements, HVAC alternator was confirmed as the main cause for whistling noise.

The suspension system in a vehicle isolates the frame and body from road shocks and vibrations which would otherwise be transferred to the passengers and goods. Heavier goods vehicles use tandem axles at the rear for load carrying. Both the axles should be inter-connected to eliminate overloading of any one axle when this goes over a bump or a ditch. One of the inter-connecting mechanism used is leaf spring with tie rod, bell crank & linkages, when the first rear axle moves over a bump, the linkages equalize the loading on the second rear axle. This paper details about the failure analysis methodology to simulate the tie rod field failure using a six poster road simulator and to identify the root cause of the failure and further corrective actions.

Driveline (DL) is one of the major sources of noise and vibration which excites the vehicle structures across a wide band of frequencies in commercial vehicles (CV). Current work focuses on the driveline noise source identification and its reduction in a heavy commercial vehicle. An abnormal noise is perceived in a CV in high gears at high speeds. This annoying DL noise is subjectively perceived in geared and neutral coast down conditions. Objective NVH assessment including near source noise and vibration of the driveline components was performed to quantify the noise. Initial test results revealed that the DL excitations are aggravated in auxiliary gear box as broadband rattle noise. The design configuration of the DL components and related subsystems such as propeller shafts and gearbox etc. was studied to the find root cause of the excitations. The driveline configuration including the auxiliary gearbox tooth geometry is also scrutinized and modified.

Development of split Catalytic Converter (Cat-Con)-Muffler system was done to be used in front engine low floor (FELF) Bus from perspective of cost saving, modularity and reduction in complexity. This system is developed as an alternate to an existing solution of integrated Cat-Con and muffler. The paper describes the development of a split Cat-Con and muffler exhaust system for a FELF Bus, so as to meet cost and time considerations. The development also had to achieve a feasible solution, which could be installed within the packaging volume of the existing configuration of FELF while meeting the regulatory requirements [1] for Pass by noise (PBN), and at the same time conforming to backpressure limits set for optimum engine performance. Multiple design - prototypes - test iterations were carried out to meet the PBN and back pressure target for FELF Bus. The final solution was developed which achieved both the requirements within the specified space constraints.

Tippers used for transporting blue metal, construction and mining material is designed with different types of load body to suit the material being carried, capacity and its application. These load bodies are constructed with high strength material to withstand forces under various operating conditions. Structural strength verification of load body using FEM is conducted, by modelling forces due to payload as a pressure function on the panels of the load body. The spatial variation of pressure is typically assumed. In discrete element method (DEM) granular payload material such as gravel, wet or dry sand, coal etc., can be modelled by accounting its flow and interaction with structure of load body for prediction of force/pressure distribution. In this paper, coupled FE-DEM is used for determining pressure distribution on loading surfaces of a tipper body structure of a heavy commercial vehicle during loading, unloading and transportation.

The cost incurred to make design modifications to solve NVH problems increases with maturity of design in the development process. Hence NVH issues should be addressed in the initial phase to avoid any significant changes in structure and subsequent changes in overall performance of the vehicle. Hybrid methodology with application of advanced testing and Computer Aided Engineering (CAE) tools to achieve full vehicle NVH attribute targets is nowadays a must for this reason. This paper represents a case study on low frequency NVH performance evaluation and refinement for heavy commercial vehicle truck using Hybrid Test-CAE methodology. To achieve better NVH performance, it is important to set competitive overall vehicle level NVH targets and cascade it down to system and sub-system targets. Test-CAE correlation has been carried out to validate Finite element (FE) modeling procedure and methodology.

Steering wheel being the most used tactile point in a vehicle, its feel and response is an important factor based on which the vehicle quality is judged. Engineering the right feel and response into the system requires knowledge of the objective parameters that relate to the driver perception. Extensive correlation work has been done in the past pertaining to passenger cars, but the driver requirements for commercial vehicles vary significantly. Often it becomes difficult to match the right parameters to the steering feel experienced by the drivers, since most of the standard ISO weave test units used to describe them are of zero or first order parameters. Analyzing the second order parameters gave a better method to reason driver related feel. Also, each subjective attribute was fragmented into sub-attributes to identify the reason for such a rating resulting in the identification of the major subjective parameters affecting driver ratings.

The Bogie suspensions ensure better stability at higher loads and also give the utmost reliability under extreme climatic conditions with minimum maintenance. Many vehicle manufactures have adopted for the bogie suspension at rear based on its advantages. The noises generated from the vehicle in the field includes engine noises and flow noises and hence it is very difficult to clearly discern the noise generated from suspension system of the vehicle [1]. Most suspension system noises do not come from a single part but they are caused by the coupling action between related parts, making it difficult to clearly identify the exact cases. This paper details the overall approach to identify the bogie suspension noise on a commercial vehicle and countermeasures to reduce the same.