Search Results

Disc brakes operate with very close proximity of the brake pads and the brake rotor, with as little as a tenth of a millimeter of movement of the pads required to bring them into full contact with the rotor to generate braking torque. It is usual for a disc brake to operate with some amount of residual drag in the fully released state, signifying constant contact between the pads and the rotor. With this contact, every miniscule movement of the rotor pushes against the brake pads and changes the forces between them. Sustained loads on the brake corner, and maneuvers such as cornering, can both produce rotor movement relative to the caliper, which can push it steadily against one or both of the brake pads. This can greatly increase the residual force in the caliper, and increase drag. This dependence of drag behavior on the movement of the brake rotor creates some vehicle-dependent behavior.

A student team from Brigham Young University (BYU) set a new record for the world's fastest electric drag racecar. The team modified a production EV1 donated to the university by the General Motors Corporation and installed a bank of 160 UltraCapacitors rated at 2700 farads each. This paper describes the design of the capacitor pack, the car's drive train, the charging method and other modifications of the vehicle. Here we also discuss performance and race data from an official quarter-mile drag race sanctioned by the National Electric Drag Racing Association. A simulation model for vehicle performance was also developed and is presented here.

In the context of vehicle electrification, improving vehicle aerodynamics is not only critical for efficiency and range, but also for driving experience. In order to balance the necessary trade-offs between drag and downforce without significant impact on the vehicle styling, we see an increasing amount of active aerodynamic solutions on high-end passenger vehicles. Active rear spoilers are one of the most common active aerodynamic features. They deploy at high vehicle speed when additional downforce is required [1, 2]. For a vehicle with an active rear spoiler, the aerodynamic performance is typically predicted through simulations or physical testing at different static spoiler positions. These positions range from fully stowed to fully deployed. However, this approach does not provide any information regarding the transient effects during the deployment of the rear spoiler, which can be critical to understanding key performance aspects of the system.

NASA's plans to implement the Vision for Space Exploration include extensive human-robot cooperation across an enterprise spanning multiple missions, systems, and decades. To make this practical, strong enterprise-level interface standards (data, power, communication, interaction, autonomy, and physical) will be required early in the systems and technology development cycle. Such standards should affect both the engineer and operator roles that humans adopt in their interactions with robots. For the engineer role, standards will result in reduced development lead-times, lower cost, and greater efficiency in deploying such systems. For the operator role, standards will result in common autonomy and interaction modes that reduce operator training, minimize workload, and apply to many different robotic platforms. Reduced quantities of spare hardware could also be a benefit of standardization.

The importance of achieving good (low) assembled lateral runout of the brake disc is well recognized in the industry - it is a critical feature for avoiding issues such as wear-induced disc thickness variation and vibration/shudder during braking. Significant efforts and expense has been invested by the industry into reducing disc brake lateral runout. However, wheel assemblies also have some inherent runout, which in turn cause cyclical forces to act on the brake corner during vehicle movement. Despite the stiffness of the wheel bearing (which aligns the brake disc with the caliper and knuckle), these “tire non-uniformity” forces can be sufficient to promote deflection of the assembly that is appreciable compared to typical disc lateral runout tolerances. This paper covers measurements of this phenomenon on three different vehicles (compact, mid-size, and large cars), under a variety of operating conditions such as speed, wheel assembly runout, and wheel assembly balance.

This study evaluates utilizing an accelerated test method that correlates customer interaction with a vehicle seat where bagginess and wrinkling is produced. The evaluation includes correlation from warranty returns as well as test vehicle results for test verification. Consumer metrics will be discussed within this paper with respect to potential application of this test method, including but not limited to JD Power ratings. The intent of the test method is to aid in establishing appropriate design parameters of the seat trim covers and to incorporate appropriate design measures such as tie downs and lamination. This test procedure was utilized in a Design for Six Sigma (DFSS) project as an aid in optimizing seat parameters influencing trim cover performance using a Design of Experiment approach. Presenter Lisa Fallon, General Motors LLC

The design optimization of thin-walled tubular structures is of relevance in the automotive industry due to their low cost, ease of manufacturing and installation, and high-energy absorption efficiency. This study presents a methodology to design thin-walled tubular structures for crashworthiness applications. During an impact, thin-walled tubular structures may exhibit progressive collapse/buckling, global collapse/buckling, or mixed collapse/buckling. From a crashworthiness standpoint, the most desirable collapse mode is progressive collapse due to its high-energy absorption efficiency, stable deformation, and low peak crush force (PCF). In the automotive industry, thin-walled components have complex structural geometries. These complexities and the several loading conditions present in a crash reduce the possibility of progressive collapse. The Hybrid Cellular Automata (HCA) method has shown to be an efficient continuum-based approach in crashworthiness design.

Third generation advanced high strength steels (AHSS) that rely on the transformation of austenite to martensite have gained growing interest for implementation into vehicle architectures. Previous studies have identified a dependency of the rate of austenite decomposition on the amount of strain and the associated strain path imposed on the sheet. The rate and amount of austenite transformation can impact the work hardening behavior and tensile properties. However, a deeper understanding of the impact on toughness, and thus crash performance, is not fully developed. In this study, the strain path and strain amounts were systematically controlled to understand the associated correlation to impact toughness in the end application condition (strained and baked). Impact toughness was evaluated using an instrumented Charpy machine with a single sheet v-notch sample configuration.

The high performance brake systems of today are usually in a delicate balance - walking the fine line between being overpowered by some of the most potent powertrains, some of the grippiest tires, and some of the most demanding race tracks that the automotive world has ever seen - and saddling the vehicle with excess kilograms of unsprung mass with oversized brakes, forcing significant compromises in drivability with oversized tires and wheels. Brake system design for high performance vehicles has often relied on a very deep understanding of friction material performance (friction, wear, and compressibility) in race track conditions, with sufficient knowledge to enable this razor’s edge design.

Robust engineering is an integral part of the quality initiative, Design For Six Sigma (DFSS), in most companies to enable good designs and products for reliability and durability. Taguchi’s signal-to-noise ratio has been considered as a good performance index for robustness for many years. An alternate approach that is direct and simple for measuring robustness is proposed. In this approach, robustness is measured in terms of an augmented output response and it is a composite index of variation and efficiency of a system. This formulation represents an engineering design intent of a product in a statistical sense, so engineers can understand, communicate, and resonate at ease. Robust formulations are illustrated and discussed with case studies for smaller-the-better, nominal-the-best, and dynamic responses. Confirmation runs of optimization show good agreement of the augmented response with the additive predictive models.

This report describes the aircraft designed and built by the Brigham Young University Idaho (BYU-Idaho) Aero Design Team. The aircraft was built for the SAE Aero East Competition 2017 hosted in Lakeland, Florida. The objective is to design an all-electric aircraft optimized to carry as much weight as possible, while also minimizing the empty weight of the aircraft capable of successfully completing a flight circuit. A flight circuit is defined as flying completely around two safety cones for a total distance of about 726ft. The challenge has provided the team with the opportunity to improve design and manufacturing skills, while also gaining experience in real life engineering challenges. As a result, the team greatly increased their knowledge of aeronautical design and manufacturing. BYU-Idaho has developed a balsa/plywood carbon fiber reinforced fixed wing aircraft weighing approximately .7lbs, capable of carrying more than 4lbs.

The validation of brake discs has remained, to this day, heavily reliant on “Thermal Abuse” or “Thermal Cracking” type testing, with many procedures so dated that most engineers active in the industry today cannot even recall the origin of the test. These procedures - of which there are many variants - all share the trait of greatly accelerating durability testing by performing repeated high power (high speed and high deceleration) brake applies to drive huge temperature gradients and internal stress, and often allowing the disc to get very hot, to where the strength of the material from which the disc is constructed is significantly degraded. There is little debate about whether these procedures work; by and large disc durability issues in the field are extremely rare.

This report presents the results of a CFD study to develop a bodywork package to improve the aerodynamic performance of the Brigham Young University (BYU) Electric Streamliner. A comparison of the pressure distribution and the flow around the baseline and final ‘recommended’ configuration is also presented. The effect of the CFD developed body geometry to the vehicle has been to increase downforce by almost 300lbf when it is at 200mph, while reducing drag by 8.5lbf. The final lift to drag ratio is -1.56 as compared to the .67 baseline.

Exterior component integration presents competing performance challenges for balanced exterior styling, safety, ‘structural feel’ [1] and durability. Industry standard practices utilize noise and vibration mode maps and source-path-receiver [2] considerations for component mode frequency placement. This modal frequency placement has an influence on ‘structural feel’ and durability performance. Challenges have increased with additional styling content, geometric overhang from attachment points, component size and mass, and sensor modules. Base excitation at component attachment interfaces are increase due to relative positioning of the suspension and propulsion vehicle source inputs. These components might include headlamps, side mirrors, end gates, bumpers and fascia assemblies. Here, we establish basic expectations for the behavior of these systems, and ultimately consolidate existing rationales that are applied to these systems.

Fretting is an important phenomenon that happens in many mechanical parts. It is the main reason in deadly failures in automobiles, airliners, and turbine engines. The damage is noticed between two surfaces clamped together by bolts or rivets that are nominally at rest, but have a small amplitude oscillation because of vibration or local cyclic loading. Fretting damage can be divided into two types. The first type is the fretting fatigue damage where a crack would initiate and propagate at specific location at the interface of the mating surfaces. Cracks usually initiate in the material with lower strength because of the local cyclic loading conditions which eventually lead to full failure. The second type is the fretting wear damage because of external vibration. Researchers have investigated this phenomenon by theoretical modeling and experimental approaches. Although a lot of research has been done on fretting damage, some of the parameters have not been well studied.

Styrene-Butadiene Rubber (SBR), a copolymer of butadiene and styrene, is widely used in the automotive industry due to its high durability and resistance to abrasion, oils and oxidation. Some of the common applications include tires, vibration isolators, and gaskets, among others. This paper characterizes the dynamic behavior of SBR and discusses the suitability of a visco-elastic model of elastomers, known as the Kelvin model, from a mathematical and physical point of view. An optimization algorithm is used to estimate the parameters of the Kelvin model. The resulting model was shown to produce reasonable approximations of measured dynamic stiffness. The model was also used to calculate the self heating of the elastomer due to energy dissipation by the viscous damping components in the model. Developing such a predictive capability is essential in understanding the dynamic behavior of elastomers considering that their dynamic stiffness can in general depend on temperature.

Very few activities the brake engineer engages in can induce as much vexation as trying to find a satisfying routing for the flexible brake components such as hoses, wheel speed sensors, and electric parking brake cables. Ever increasing wheel end content, ever decreasing space, more complex suspensions, and bulkier (but lighter weight) suspension components provide quite the morass through which the components must be routed through. When routing is finalized - and free of any major issues - there frequently remains some combinations of articulation position and component tolerances that allow a light “friendly” touch between components (such as a sensor wire and a surface of a bracket or strut tube), or near misses where clearance exists but raises “what if” questions around what would happen if the tolerances would stack up slightly differently on another vehicle.

The Lockheed Martin Low-Speed Wind Tunnel (LSWT) is a closed-return wind tunnel with two solid-wall test sections. This facility originally entered into service in 1967 for aerodynamic research of aircraft in low-speed and vertical/short take-off and landing (V/STOL) flight. Since this time, the client base has evolved to include a significant level of automotive aerodynamic testing, and the needs of the automotive clientele have progressed to include acoustic testing capability. The LSWT was therefore acoustically upgraded in 2016 to reduce background noise levels and to minimize acoustic reflections within the low-speed test section (LSTS). The acoustic upgrade involved detailed analysis, design, specification, and installation of acoustically treated wall surfaces and turning vanes in the circuit as well as low self-noise acoustic wall and ceiling treatment in the solid-wall LSTS.

Accurate measurements of brake friction materials are critical to understanding brake behaviors during testing. Current methods typically utilize a hand gauge (or a machine, in some cases) to sample various discrete points on the brake lining. This approach limits measurements to planar wear characteristics, taper and thickness, and excludes more complex measurements such as cupping. The limited number of points means that a single errant point measurement or the choice of point locations can have a large impact on the reported wear measurement. This paper will describe a method for utilizing a Coordinate Measurement Machine (CMM) fitted with a laser line scanning tool to generate a point cloud of data that can then be compared to an earlier measurement of the same piece or to a math model. This method produces thousands of data points which allows for more accurate volumetric wear calculations and color maps of the entire friction face.

Market demands for increased fuel economy and reduced emissions are placing higher aerodynamic and thermal analysis demands on vehicle designers and engineers. These analyses are usually carried out by different engineering groups in different parts of the design cycle. Design changes required to improve vehicle aerodynamics often come at the price of part thermal performance and vice versa. These design changes are frequently a fix for performance issues at a single performance point such as peak power, peak torque, or highway cruise. In this paper, the motivation for a holistic approach in the form of multi-disciplinary optimization (MDO) early in the design process is presented. Using a Response-surface Informed Transient Thermal Model (RITThM) a vehicle's thermal performance through a drive cycle is predicted and correlated to physical testing for validation.