Search Results

Stringent automotive legislation is driving requirements for increasingly complex battery pack solutions. The key challenges for battery pack development drive cost and performance optimisation, growth in architecture solutions, monitoring and safety through lifetime, and faster-to-market expectations. The battery Virtual Product Development (VPD) toolchain addresses these challenges and provides a solution to reduce the battery pack development time, cost and risk. The battery VPD toolchain is built upon scalable, validated sub-models of the battery pack that capture the interactions between the various domains; mechanical, electrical, thermal and hydraulic. The model fidelity can be selected at each stage of the design process allowing the right amount of detail, and available data, to be incorporated. The toolchain is coupled with vehicle simulation tools to rapidly assess performance of the complete electrified powertrain.

A Range-Extended Electric Vehicle (REEV) usually has an auxiliary power source that can provide additional range when the main Rechargeable Energy Storage System (RESS) runs out. The range extender can be a fuel cell, a gas turbine, or an Internal Combustion Engine (ICE) bolted to a generator. Sizing the powertrain for a REEV is primarily to investigate the relationship between the capacity of the main RESS and the power rating of the range extender. Worldwide harmonized Light vehicles Test Procedures (WLTP) introduced a Utility Factor (UF) which is a curve used to calculate the weighted test results for the Off-Vehicle Charging-Hybrid Electric Vehicle (OVC-HEV) from the measured Charge Depleting (CD) mode range result, and the Charge Sustaining (CS) mode Fuel Consumption (FC). Therefore, the RESS capacity, the range extender power rating, the control strategy, and the UF are the key factors affecting the weighted FC of a REEV on the test cycle.

It has been recognized that density, viscosity, surface tension, and volatility of liquid fuel are of great importance on the atomization and vaporization characteristics of biodiesel spray. This paper presents a comprehensive physical property prediction of biodiesel fuel for spray modeling with most recently developed property prediction models. The temperature-dependent properties of a soy methyl ester (SME) biodiesel were well predicted by the updated prediction methods. Then, the physical properties of the SME biodiesel were added into the KIVA-3V fuel library. By using the well predicted fuel properties, the spray behaviors of SME were successfully simulated by the KIVA-3V code under late-cycle post-injection, conventional diesel injection, and early-injection engine-relevant conditions. The simulation results agree reasonably well with the available experimental liquid penetrations under conditions of various ambient densities and temperatures.

Most major regional automotive markets have stringent legislative targets for vehicle greenhouse gas emissions or fuel economy enforced by fiscal penalties. Large improvements in vehicle efficiency on mandated test cycles have already taken place in some markets through the widespread adoption of technologies such as downsizing or dieselization. There is now increased focus on approaches which give smaller but significant incremental efficiency benefits such as reducing parasitic losses due to engine friction. Fuel economy improvements which achieve this through the development of advanced engine lubricants are very attractive to vehicle manufacturers due to their favorable cost-benefit ratio. For an engine with components which operate predominantly in the hydrodynamic lubrication regime, the most significant lubricant parameter which can be changed to improve the tribological performance of the system is the lubricant viscosity.

The flow performance of intake port significantly affects engine output power, fuel economy, and exhaust emissions in gasoline engines. Thus, optimal intake port geometry is desired in gasoline engines. To optimize the flow performance of intake port, a new optimization method combining genetic algorithm (GA) and artificial neural network (ANN) was proposed. First, an automatic system for generating the geometry of the tangential intake port was constructed to create various port geometries through inputting the 18 pre-defined structural parameters. Then, the effects of four critical structural parameters were investigated through numerical simulation. On the basis of the computational results, an ANN was used to model the flow performance of the intake port, and a genetic algorithm was simultaneously employed to optimize the flow performance by optimizing the four important structural parameters. Finally, the optimization results were verified through numerical simulation.

Fuel consumption, and the physical behaviours behind it, have never been of greater interest to the automotive engineering community. The enormous design, development and infrastructure investment involved with a new engine family which will be in production for many years demands significant review of the base engine fundamental architecture. Future CO2 challenges are pushing car manufacturers to consider alternative engine configurations. As a result, a wide range of diesel engine architectures are available in production, particularly in the 1.4 to 1.6 L passenger car market, including variations in cylinder size, number of valves per cylinder, and bore:stroke (B/S) ratio. In addition, the 3 cylinder engine has entered the market in growing numbers, despite its historic NVH concerns. Ricardo has performed a generic architecture study for a midsize displacement engine in order to assess the pros and cons of each engine configuration.

Controlled Auto-Ignition (CAI) combustion, also known as Homogeneous Charge Compression Ignition (HCCI), has the potential to simultaneously reduce the fuel consumption and nitrogen oxides emissions of gasoline engines. However, narrow operating region in loads and speeds is one of the challenges for the commercial application of CAI combustion to gasoline engines. Therefore, the extension of loads and speeds is an important prerequisite for the commercial application of CAI combustion. The effect of intake charge boosting, charge stratification and spark-assisted ignition on the operating range in CAI mode was reviewed. Stratified flame ignited (SFI) hybrid combustion is one form to achieve CAI combustion under the conditions of highly diluted mixture caused by the flame in the stratified mixture with the help of spark plug.

In-cylinder flow characteristics in a four-stroke diesel engine were studied experimentally by instantaneous measurements of swirl and squish flow velocity distribution with particle image velocimetry (PIV). The triple-exposed PIV films were interrogated on a self-made system to get the velocity distribution. The measured velocities were analyzed by spatially high-pass and low-pass filtering techniques. Vorticity distributions were also calculated using the measured data. As results, vortex structure of the flow field was clearly visualized. Spatially averaged in-cylinder flow energy was found decaying at high rate but the less-scaled flow components at much lower rate. Clearly visualized squish and reverse squish movements around the top dead center (TDC) during the compression stroke were found strongly affecting the swirl flow field. making the in-bowl flow energy increased.

In this paper, an experimental study was performed to investigate characteristics of flame propagation and knocking combustion of hydrous (10% water content) and anhydrous ethanol at different air/fuel ratios in comparison to RON95 gasoline. Experiments were conducted in a full bore overhead optical access single cylinder port-fuel injection spark-ignition engine. High speed images of total chemiluminescence and OH* emission was recorded together with the in-cylinder pressure, from which the heat release data were derived. The results show that under the stoichiometric condition anhydrous ethanol and wet ethanol with 10% water (E90W10) generated higher IMEP with at an ignition timing slightly retarded from MBT than the gasoline fuel for a fixed throttle position. Under rich and stoichiometric conditions, the knock limited spark timing occurred at 35 CA BTDC whereas both ethanol and E90W10 were free from knocking combustion at the same operating condition.

Biodiesel is a widely used biofuel in diesel engines, which is of particular interest as a renewable fuel because it possesses the similar properties as the diesel fuel. The pure soybean biodiesel was tested in an optical constant volume combustion chamber using natural flame luminosity and forward illumination light extinction (FILE) methods to explore the combustion process and soot distribution at various ambient temperatures (800 K and 1000 K) and oxygen concentrations (21%, 16%, 10.5%). Results indicated that, with a lower ambient temperature, the autoignition delay became longer for all three oxygen concentrations and more ambient air was entrained by spray jet and more fuel was burnt by premixed combustion. With less ambient oxygen concentration, the heat release rate showed not only a longer ignition delay but also longer combustion duration.

A very competitive alcohol for use in diesel engines is butanol. Butanol is of particular interest as a renewable bio-fuel, as it is less hydrophilic and it possesses higher heating value, higher cetane number, lower vapor pressure, and higher miscibility than ethanol or methanol. These properties make butanol preferable to ethanol or methanol for blending with conventional diesel or gasoline fuel. In this paper, the spray and combustion characteristics of pure n-butanol fuel was experimentally investigated in a constant volume combustion chamber. The ambient temperatures were set to 1000 K, and three different oxygen concentrations were set to 21%, 16%, and 10.5%. The results indicate that the penetration length reduces with the increase of ambient oxygen concentration. The combustion pressure and heat release rate demonstrate the auto-ignition delay becomes longer with decreasing of oxygen concentrations.

Poppet-valve two-stroke gasoline engines can increase the specific power of their four-stroke counterparts with the same displacement and hence decrease fuel consumption. However, knock may occur at high loads. Therefore, the combustion with stratified lean mixture was proposed to decrease knock tendency and improve combustion stability in a poppet-valve two-stroke direct injection gasoline engine. The effect of intake pressure and split injection on fuel distribution, combustion and knock intensity in lean mixture conditions at high loads was simulated with a three-dimensional computational fluid dynamic software. Simulation results show that with the increase of intake pressure, the average fuel-air equivalent ratio in the cylinder decreases when the second injection ratio was fixed at 70% at a given amount of fuel in a cycle.

The aim of this study is to evaluate the Fuel Economy (FE) over the driving cycle for a 48 Volt P2 technology vehicle with different component ratings (battery and electric machine) in the hybrid powertrain, using simulation and Design of Experiments (DoE) tools. The P2 architecture was selected for this study based on an initial assessment of a wide number of possibilities, using the Ricardo “Architecture Independent Modelling (AIM)” toolset. This allows rapid evaluation of different powertrain options independently of a defined hybrid control strategy. For the vehicle with P2 architecture, a DoE test matrix of battery capacity and electric machine power rating was created. The test matrix was then imported into the simulation environment to perform the driving cycle FE simulations. Then, a 48 V P2 Hybrid Electric Vehicle (HEV) FE emulator model was created and interrogated using model visualisation and optimisation methods.

Rolling element bearings are known to give reduced friction losses when compared to the hydrodynamic bearings typically used to support the crankshaft in multi-cylinder engines. This paper describes the design, manufacturing and testing of a modified 4 cylinder light duty Diesel production engine with rolling element bearings applied at the crankshaft main bearings in view of CO2 emission reduction. Selection of the most suitable type of roller bearings for this specific application was made. Technology development through multi-body dynamic simulation and component testing was done to assess the effect on rolling elements performance due to the key challenges inherent to such bearing solution: high instantaneous combustion load, lubrication with low viscosity and contaminated oil, and the cracking process to split the bearing outer raceway.

A great deal of effort has been directed towards Gasoline HCCI engines, which have the potential of providing better fuel economy and emission characteristics than conventional SI engines. For stable HCCI engine operation, cycle-by-cycle based closed-loop control is needed. Such a control scheme requires an accurate and reliable sensor to monitor the combustion and provide a feedback signal. At present, the general method used to measure the combustion parameters is to monitor in-cylinder pressure with a cylinder pressure sensor. However, using in-cylinder pressure transducers is not feasible for use in mass production of HCCI engines. A good substitute to get information about combustion is the knock sensor, which is already equipped on engines on a large scale. In this paper, the knock signal from an HCCI engine equipped with 4VVAS is analyzed in detail to find the relationship between the combustion parameters and the knock sensor signal.

An experimental study has been carried out with the end goal of minimizing engine-out methane emissions with Premixed Micro Pilot Combustion (PMPC) in a natural gas-diesel Dual-Fuel™ engine. The test engine used is a heavy-duty single cylinder engine with high pressure common rail diesel injection as well as port fuel injection of natural gas. Multiple variables were examined, including injection timings, exhaust gas recirculation (EGR) percentages, and rail pressure for diesel, conventional Dual-Fuel, and PMPC Dual-Fuel combustion modes. The responses investigated were pressure rise rate, engine-out emissions, heat release and indicated specific fuel consumption. PMPC reduces methane slip when compared to conventional Dual-Fuel and improves emissions and fuel efficiency at the expense of higher cylinder pressure.

Future demands for very low emissions from diesel engines, without compromising fuel economy or driveability, require Engine Management Systems (EMS) capable of compensating for emissions dispersion caused by production tolerances and component ageing. The Advanced Diesel Engine Control (ADEC) Project, a collaboration between Ricardo and General Motors, is aimed at reducing engine-out emissions dispersion and enabling alternative combustion modes, such as Highly Premixed Cool Combustion (HPCC), in real-world scenarios. This is being achieved by high-level co-ordination of fuel, air and EGR in order to meet the conflicting performance requirements of current and future diesel engines. A sensor feasibility study was undertaken which included a number of new sensing technologies appropriate for future mass production. Two sensor types, namely cylinder pressure and accelerometer sensors, were then selected to demonstrate varying degrees of benefits versus sensor technology cost.

The Lambert-Beer's coefficient K was measured in a wide range of temperatures (400-1200K) and pressures (2-8.2 MPa) in this paper. Based on the measured MAP of K and principle of energy conservation in the sprays mass and transfer, a quantitative presentation of equivalence ratio and temperature in vapor phase sprays at diesel engine like conditions was put forward. The experimental range of temperatures was 800-1100K and 20-100 kg/m₃ for density. It was found that the maximum equivalence ratio of vapor phase spray remained fairly constant at about 3.0 and the maximum equivalence ratio appearance earlier as the ambient density increased, while the ambient temperature in the constant volume vessel was set at 800K. The maximum equivalence ratio of vapor phase spray increased from about 3.0 to about 3.7 as ambient temperature increased from 800 to 1100K.

The purpose of the European « SPACE LIGHT » (Whole SPACE combustion for LIGHT duty diesel vehicles) 3-year project launched in 2001 is to research and develop an innovative Homogeneous internal mixture Charged Compression Ignition (HCCI) for passenger cars diesel engine where the combustion process can take place simultaneously in the whole SPACE of the combustion chamber while providing almost no NOx and particulates emissions. This paper presents the whole project with the main R&D tasks necessary to comply with the industrial and technical objectives of the project. The research approach adopted is briefly described. It is then followed by a detailed description of the most recent progress achieved during the tasks recently undertaken. The methodology adopted starts from the research study of the in-cylinder combustion specifications necessary to achieve HCCI combustion from experimental single cylinder engines testing in premixed charged conditions.

Engine downsizing is one of the most effective means to improve the fuel economy of spark ignition (SI) gasoline engines because of lower pumping and friction losses. However, the occurrence of knocking combustion or even low-speed pre-ignition at high loads is a severe problem. One solution to significantly increase the upper load range of a 4-stroke gasoline engine is to use 2-stroke cycle due to the double firing frequency at the same engine speed. It was found that a 0.7 L two-cylinder 2-stroke poppet valve gasoline engine equipped with a two-stage serial boosting system, comprising a supercharger and a downstream turbocharger, could replace a 1.6 L naturally aspirated 4-stroke gasoline engine in our previous research, but its fuel economy was close to that of the 4-stroke engine at upper loads due to knocking combustion.