Search Results

The aerospace industry is noticing significant shift towards More Electric Aircraft (MEA). The advancement of electrical technology the systems are being transformed towards electric compared to the conventional pneumatic or hydraulic systems. This has led to an increased demand in electrical power from 150 Kilo Watts in the conventional airplane to 1 Mega Watts in More Electric Aircraft. More electric systems, call for increased electrical wiring harness to connect various systems in the aircraft. These harnesses consist of power and data cables. Wireless communication technology is being matured for data communication, leading to reduction of wire harness for data. As of now, the length of wires in large commercial aircraft is over 100miles and it may not be surprising if the electrification of aircraft drive this too much longer.

The growth in global economies has led to a world that has become much more mobile in the last few decades. The number of enplanements has increased and is expected to continue to do so at an annual average rate of 1.8% through 2039 [1]. Prior to the COVID-19 pandemic, the number of aircraft in service was expected to increase annually to meet the travel demand. Next-generation, more-complex aircraft were scheduled to replace the older aircraft at a pace that still allowed sufficient capacity to meet the increasing demand. The events of 2020 have driven the industry to accelerate retirement of older aircraft while deferring the introduction of new aircraft. While the length of the industry recovery period cannot be predicted, most analysts believe that demand for travel will return once a vaccine is widely available.

The aircraft jet engine is one of the most complex multivariable systems with multiple inputs and multiple outputs. To attempt to optimize control functions or to address diagnostic problems, a detailed knowledge of all jet engine design parameters and performances is required. Although jet engines have been around for almost a century, there are only a few companies in the world presently designing and manufacturing them; as such these companies possess detailed knowledge of all relevant design characteristics and performance parameters. In the event where jet engine technical details are unknown, or only a few of them are known from manufacturer’s catalogues, the challenge becomes how to calculate and extrapolate critical performance parameters based on only fuel flow, jet exhaust temperature and total thrust.

Since the beginning of aviation, aircraft designers, researchers, and pilots have monitored the skies looking for clouds to determine when and where to fly as well as when to deice aircraft surfaces. Seeing a cloud has generally consisted of looking for a white / grey puffy orb floating in the sky, indicating the presence of moisture. A simple monitoring of a temperature gauge or dew point sensor was used to help determine if precipitation was likely or accumulation of ice / snow on the airframe could occur. Various instruments have been introduced over the years to identify the presence of clouds and characterize them for the purposes of air traffic control weather awareness, icing flight test measurements, and production aircraft ice detection. These instruments have included oil slides, illuminated rods, vibrating probes, hot wires, LIDAR, RADAR, and several other measurement techniques.

Aircraft Manufacturing procedures are very critical which always require skillful engineers who must adhere to various process and procedure during daily work. The challenge is not only to identify right tools and manuals but also to keep track of operator usage data and behavior. With Augmented reality (AR), intelligent tools and analytics, we can provide a new lease of life to first-line assembly engineers. The objective is how AR can help us to reduce rework or scrap with the concept of Industry 4.0 [1] were integrating with cutting edge technologies like machine learning and the internet of things (IoT) to meet the fundamental requirements during manufacturing. Smart Manufacturing consists of four major components Cyber-physical systems, IoT, cloud computing and cognitive computing.

In response to new safety regulations regarding aircraft icing, Collins Aerospace has developed and tested an Optical Ice Detector (OID) capable of discriminating among icing conditions appropriate to Appendix C and Appendix O of 14 CFR Part 25 and Appendix D of Part 33. The OID is a short-range, polarimetric lidar that samples the airstream up to ten meters beyond the skin of the aircraft. The intensity and extinction of the backscatter light correlate with bulk properties of the cloud, such as water content and phase. Backscatter scintillation (combined with the outside air temperature from another probe) signals the presence of supercooled large droplets (SLD) within the cloud-a capability incorporated into the OID to meet the requirements of Appendix O. Recent laboratory and flight tests of the Optical Ice Detector have confirmed the efficacy of the OID to discriminate among the various icing conditions.

A GE Aviation Systems report documents that the National Oceanic and Atmospheric Administration (NOAA) provided weather forecast data has a bias of 15 knots and a standard deviation of 13.3 knots for the 40 flights considered for the research. It also had a 0.47 bias in the temperature with a standard deviation of 0.27. The temperature errors are not as significant as the wind. There is a potential opportunity to reduce the operational cost by improving the weather forecast. The flight management system (FMS) currently uses the weather forecast, available before takeoff, to identify an optimized flight path with minimum operational costs depending on the selected speed mode. Such a flight plan could be optimum for a shorter flight because these flight path planning algorithms are very less susceptible to the accuracy of the weather forecast.

Evolving of aircraft design towards further electrification requires safe and fault-free operation of all the components. More electric aircraft are increasingly utilizing electro-mechanical actuators (EMA). EMAs are prone to jamming and subsequent failure due to large forces on the shaft. Large forces are generated due to the high reflected inertia of the electric machine rotor. To limit the force acting on the shaft, a torque limiting device is connected to the power train which can separate the rotating mass of the electric machine from the power train. In this paper, a concept of integration of torque limiter and the electric machine rotor is presented to reduce overall volume and mass. It is connected closely with the rotor, within the motor envelope. A commercially available torque limiter and an electric machine designed for actuator application are used to demonstrate the concept. While essential for safety, the torque limiter adds to the mass and size of the overall EMA.

Since the early days of aviation, when an AC-type generator became a primary source of electrical power for all aircraft systems, the demand for electrical power has steadily grown. Following rapid technology and scientific advancements in the aerospace industry, the complexity and criticality of all aircraft systems have increased to the point where multiple independent and isolated electrical power sources are required. In such an environment, with two or more variable-frequency AC-type generators that can be simultaneously activated to provide electrical power to the aircraft power distribution system, a safe power transfer process becomes a major priority. This means that any two independent aircraft AC power sources with different frequencies or phase angles cannot be connected simultaneously to a common power bus.

Pitot probes and Total Air Temperature (TAT) probes are critical to aircraft performance. They are also susceptible to becoming overwhelmed and produce erroneous outputs when flying in icing conditions, especially in high altitude ice crystal situations. When the probes are overwhelmed with ice crystals, it can have significant impacts to aircraft operations. Through design and process iterations, Collins Aerospace (also known as Rosemount Aerospace™), has developed new Appendix D compliant pitot and TAT probes that are much more capable in high ice crystal content icing environments which greatly reduce the adverse risks to the aircraft and engine systems that depend on these probes.

The Collins Aerospace Optical Ice Detector is a short-range polarimetric cloud lidar designed to detect and discriminate among all types of icing conditions with the use of a single sensor. Recent flight tests of the Optical Ice Detector (OID) aboard a fully instrumented atmospheric research aircraft have allowed comparisons of measurements made by the OID with those of standard cloud research probes. The tests included some icing conditions appropriate to the most recent updates to the icing regulations. Cloud detection, discrimination of mixed phase, and quantification of cloud liquid water content for a cloud within the realm of Appendix C were all demonstrated. The duration of the tests (eight hours total) has allowed the compilation of data from the OID and cloud probes for a more comprehensive comparison. The OID measurements and those of the research probes agree favorably given the uncertainties inherent in these instruments.

In response to safety regulations regarding aircraft icing, Collins Aerospace has developed and tested a new generation of optical ice detectors (OID Lite) intended to discriminate among icing conditions described by Appendix C and Appendix O of 14 CFR Part 25 and Appendix D of Part 33. The OID Lite is a flush-mounted, short-range, polarimetric optical sensor that samples the airstream up to two meters beyond the skin of the aircraft. The intensity and polarization of the backscatter light correlate with bulk properties of the cloud, such as cloud density and phase. Drizzle-sized droplets, mixed within a small droplet cloud, appear as scintillation spikes in the lidar signal when it is processed pulse-by-pulse. Scintillation in the backscatter (in combination with the outside air temperature monitored by another probe) signals the presence of supercooled large droplets (SLD) within the cloud—a capability incorporated into the OID Lite to meet the requirements of Appendix O.

The number of Unmanned Aircraft Systems (UAS) has been growing over the past few years and will continue to grow at a faster pace in the near future. UAS faces many challenges in certification, airspace management, operations, supply chain, and maintenance. Blockchain, defined as a distributed ledger technology for the enterprise that features immutability, traceability, automation, data privacy, and security, can help address some of these challenges. However, blockchain also has certain drawbacks and, additionally, it is still not fully mature. Hence it is essential to study how blockchain can help UAS. This Aerospace Information Report (AIR) presents the current opportunities, challenges of UAS operating at or below 400 ft Above Ground Level (AGL) altitude for commercial use and how blockchain can help meet these challenges. It also provides requirements for developing a blockchain solution for UAS along with the need for the standardization of blockchain enabled processes.

Unmanned Aircraft Systems (UAS) have been growing over the past few years and will continue to grow at a faster pace in future. UAS faces many challenges in certification, airspace management, operations, supply chain, and maintenance. Blockchain, defined as a distributed ledger technology for the enterprise that features immutability, traceability, automation, data privacy, and security, can help address some of these challenges. However, blockchain also has certain challenges and is still evolving. Hence it is essential to study on how blockchain can help UAS. G-31 technical committee of SAE International responsible for electronic transactions for aerospace has published AIR 7356 [1] entitled Opportunities, Challenges and Requirements for use of Blockchain in Unmanned Aircraft Systems Operating below 400ft above ground level for Commercial Use. This paper is a teaser for AIR 7356 [1] document.

The main aim of operating the navigation database server from ground station (Web/cloud) is to operate a single navigation database server across all aircrafts and navigation database updates can be performed at one place. which will be effective and quick, thus no need to update the navigation database in each flight for every 28 days. UAM refers to a safe and efficient air transportation system that uses transformative new airborne technology, manned and unmanned, to move people and goods in a metropolitan area, operating the navigation data base server from ground station might be the first step towards including the FMS system in urban air mobility (UAM). the proposed system can run as standalone application and provides serveries to all aircrafts from single resource; thus, the system will provide services with low cost.

This work presents the anti-icing simulation results from a pressure sensing probe. This study used various turbulence models to understand their influence in surface temperature prediction. A fully turbulence model and a transition turbulence model are considered in this work. Both dry air and icing conditions are considered for this study. The results show that at low Angle of Attack (AOA) both turbulence model results compared well and at higher AOA the results deviated. Overall, as AOA increases, the k-ꞷ SST model predicted the surface temperature colder than the Transition SST model result.

For nearly a century, ice build-up on aircraft surfaces has presented a safety concern for the aviation industry. Pilot observations of visible moisture and temperature has been used a primary means to detect conditions conducive to ice accretion on aircraft critical surfaces. To help relieve flight crew workload and improve aircraft safety, various ice detection systems have been developed. Some ice detection systems have been successfully certified as the primary means of detecting ice, negating the need for the flight crew to actively monitor for icing conditions. To achieve certification as a Primary ice detection system requires detailed substantiation of ice detector performance over the full range of icing conditions and aircraft flight conditions. Some notable events in the aviation industry have highlighted certain areas of the icing envelope that require special attention.

This paper provides an overview of the state-of-art multiscale “Icing Simulation Framework” capability developed at Raytheon Technologies Research Center. Specifically, the application of this framework to simulate droplet runback and runback icing will be presented. In summary, this high-fidelity framework tracks the physical mechanisms associated with droplet dynamics, ice nucleation, growth and interaction with the environment (e.g. adhesion, crystal growth, evaporation, sublimation, etc.) across all relevant scales (including nucleation at <10-7m to ~10-6m of coating/environment interaction to 10-2m of the component) which allows a rigorous investigation of how different environmental (e.g. LWC, MVD, pressure, velocity and temperature) and substrate (e.g. coating molecular and macroscopic specifications) characteristics affect the icing behavior.

With the publication of SAE AS5562 in 2015, icing wind tunnel test facilities have upgraded their operating environments and instrumentation to meet the client demand to test to this new standard. Nearing four years of testing and development to this standard, numerous questions and challenges have arisen that industry has addressed on an individual basis but not in a common format for all. This paper addresses some of the known challenges in an effort to apply AS5562 consistently across industry and provide clarity to all users.

Avionics systems are currently undergoing a transition from single core processor architectures to multi-core processor architectures. This transition enables significant advantages in reduction in size, weight, power (SWaP) and cost. However, avionics hardware and software certification policies and guidance are evolving as research and experience is gained with multi-core processor architectures. The unique challenges of using multi-core processors in certified avionics will be discussed. The requirements for a virtualization platform supporting multiple real-time operating system (RTOS) partitions on a multi-core processor used in safety-critical avionics systems are defined, including the ability to support multiple design assurance levels (DAL) on multiple cores, fault isolation and containment, static configuration as per ARINC 653, role-based development as per DO-297, and robust partitioning to reduce cost of incremental certification.